Very nice explanation 👍😇

I set this card up with three external stepper drivers for my homemade 3 axis CNC machine. I'm using open builds control to test everything and it seems to be all working correctly. I'm wondering if I need to supply the board with 5 volts if it's not connected to USB? Or does it get all of its power from the 12-volt connector?

thanks

Can we add relay for automatic spindle switch?

can this board use for 10 watt optical power for laser diode? thanks

I can use this board with the draw cnc ?

how do you set a zero point to start from

I am having a problem like once I connect my msk laser tool for wifi and after that If I disconnect the power then my board is not connecting again I'll have to connect the board and reconnect for software while plugging so there is any to skip this ?

@douglaslim992

6 ай бұрын

Maybe you can try to reflash the firmware back to 2.10 or 2.08 as shown in the video

Можно ли подключить к этой плате старый offline contriller с кнопками?

please can you tell me about the wiring of the nema17 with mks dlc 32v2.1. I am facing issue with the running of the motors with the board.

@sashgorev

25 күн бұрын

Do you put driver boards on main board? They are sale separately in some offers.If yes check is they right connected to the main board. If yes you need data sheet for Nema motors to see what pin for what is. Good luck 🤞

What is "S" axis? I noticed mine jumped to 50 today. Weird.

Can you share the stl file for the case?

Why doesn't the mobile app have z-axis?

But here there are two "Y's" and not XYZA . How do I solve on the software? Thank you very much.

@Basement_CNC

2 ай бұрын

you cant, its a hardware limitation, since it only has 3 driver ports, and the 2y outputs are both connected to the same driver, so gantry squaring wont work either

would this work for the 2D Pen Plotter with all the same feature or is it just for laser engravers

@sashgorev

25 күн бұрын

Think yes if you're machine work with G-code commands.

if wifi setting installed are can still use in Lightburn?

@sashgorev

25 күн бұрын

Yes,go to Lightburn in settings and re-add laser again with wi-fi connection.

I am having an issue using this board. During the milling, the Z axis is going down. Do you know what happening?

@Basement_CNC

3 ай бұрын

it is probably the forces of the endmill pulling down on the z axis, and the stepper isnt strong enough to hold it in place. mayby try a straight flute or downcut endmill, the dont produce that much force pulling down

@DearChina1

Ай бұрын

Change Your stepper motor ,I got the same issues last month

@flopesff

Ай бұрын

@@DearChina1 The issue was solved? Did you use some special stepper motor?

@DearChina1

Ай бұрын

⁠@@flopesffno just replace with the same,yes isssues was solved

How are you buying it in India?! Or is there any Indian supplier?

does lightburn work with this??

@jwrtiger

6 ай бұрын

The TwoTrees Laser I have uses the same board less the display board. I have no problem using the latest version of LightBurn.

Hi sir can you please give case stl files. Dlc32 board case.

Does it support Lightburn?

@jwrtiger

6 ай бұрын

The TwoTrees Laser I have uses the same board less the display board. I have no problem using the latest version of LightBurn.

If possible to use for CNC router

@JuiceWrId_999

6 ай бұрын

Yes

@JuiceWrId_999

6 ай бұрын

It’s labeled as a cnc laser machine you just connenet a spindal to the port that says spindal

my dlc32 v2.1 board does not auto connect to wifi

@JuiceWrId_999

6 ай бұрын

L

@JuiceWrId_999

6 ай бұрын

Mine does😂😂

@douglaslim992

6 ай бұрын

Which version of firmware you installed, the latest 2.30 was disable that Wifi autoconnect feature temporarily, to fix some bugs…if you want it back, best to flash the older version, 2.10 or 2.08

Where to bay this full kit in chip price😊

@jwrtiger

6 ай бұрын

Aliexpress, usa, Both the control board and the display board for less than $20.00 USD.

@silverify

2 ай бұрын

​@@jwrtigerboth for 19, cant find that.. You mean together about 40 $?

thank you for sharing, can you share the file for the case

You realise there is almost NO support for this board and the last firmware update was a year ago?

@silverify

2 ай бұрын

Which board do you suggest to buy?

@andrikurniawan531

Ай бұрын

up

How may i contact u

I can use this board and program it with the arduino environment?

@SuperbTech

10 ай бұрын

you dont need to program it, it has built in firmware. you can directly use it using GRBL controller

@douglaslim992

6 ай бұрын

Basically it is in Arduino environment , with a integrated cnc shield.