Installing an ARB Dual Air Compressor and Switch-Pro System - 2020 Toyota 4Runner | Part 2
Автокөліктер мен көлік құралдары
PART 2 of 2
Hey everyone! I was back home for the winter and used the downtime to install the ARB Dual Air Compressor and Switch-Pro panel. Here is the video!
Shoutout to @georgiusadventure for helping me out with the wiring!
ARB Dual Air Compressor & Switch Pro Chart:
www.wheresfrancis.com/downloads
Password: youtube
Parts
----
SDOffRoadMT Mount Tray - @sdoffroadmt
SafetyHub 150 (Included with Mount Tray)
Terminal Block (Included with Mount Tray)
Circuit Breaker (Included with Mount Tray)
ARB Dual Air Compressor
ARB Pump Kit
ARB Manifold Kit
Switch-Pro SP-9100 System
SDHQ Switch Pro Panel Mount - bit.ly/3tfWR2Q
Tools
---
Klein Tools Wire Stripper - amzn.to/3IuLqKP
Klein Tools Crimper - amzn.to/3IuLqKP
Heat Shrink Wire Connectors - amzn.to/3t7989G
WETOLS Rivet Nut Tool - amzn.to/3BXHxM1
Heat Shrink Tubing Wrap - amzn.to/3pnjzou
Battery Cable Ring Terminals - amzn.to/3thqMaD
22 Gauge Wire Kit - amzn.to/3IsaGRX
Add-A-Fuse Adapters - amzn.to/3sqDHb7
Battery Cable Cutter and Wire Crimpers - amzn.to/3pnjO2S
Пікірлер: 30
New to the 5th gen and bought a ton of parts off the guy as well, including all of these. Exactly the video I needed after 4 days of searching. Will contact SD Off-road in the am to make it happen. Thanks so much for your time and effort!
Clean install and super informative video! Thanks for going in-depth on the add-a-fuse section as well for a newer 4runner.
Just wanted to say, Thank you for this video. By far the best instructions to follow with a setup like this. Legitimately have the same exact setup. Worked like a charm!
@francisngo
Жыл бұрын
Glad you found the video helpful!
Thanks Brotha!! Good music BTW.
Good install video
Super helpful!!!
This was soooo helpful Francis! Do you still have the wiring diagram you linked in your website before it went offline?
Quick sand wrapping came out awesome! Super interested to know about your vinyl wrapping experience? What product and how much did you use? How many hours did it take to wrap it around? Any comments or separate video is much appreciated!
Thanks, Francis... Super helpful... QQ: When mounting the support bracket to the fender, did you use both screws? There's a piece blocking the second screw hole coming from the small fuse box holder.
Really appreciate the guide you made! One issue I’m having is fitting the manifold in place, did you have to remove that clip holding whatever bundle of wire/tubing is tucked into the corner? Thanks!
Really appreciate the tutorial! I noticed you didnt use the rivet nut portion (the hole to the right of the switch pro) have you noticed any issues with the tray without it? Also, IDK about your install, but to fit the manifold in I had to remove the black clip holding that bundle of wire off in the corner of the engine bay.
Appreicate you putting such a high quality vid out there. Totally love it! I plan to put this install in soon. I noticed you mentioned something about taking the mount tray off so you could put the manifold on. Just want to clarify, did you mean you needed to take the mount tray off the engine mounts, or did you mean you needed to pull things (like the safety hub, etc) entirely off the mount tray to get the manifold on? I wouldn't think you'd need to take all those things off, but whey you said it took you a few hours I was thinking maybe I didn't understand. Please share your thoughts. Thank you!
@francisngo
Жыл бұрын
Thanks! Glad you found this video helpful. I know I was looking for a video like this out there but it didn't exist so I made one to help others. Yes to clarify, I meant taking the whole tray off the engine/wheel wells (keeping the shelf mounts installed on the vehicle) in order to install the manifold towards the back of the engine bay. It would be very difficult to screw the safety hub and switch pro if the mount tray is still on the shelf mount. I believe it's also mentioned in the installation guide from SDoffroadMT. Please share your feedback and message me a photo on IG once you're done! :D
Good video! Best instructions I've seen for the SD Mount Tray. What was the point of T-splicing the purple wire on the ARB Compressor? Thanks!
@francisngo
Жыл бұрын
Thanks! I am glad you found it useful! I t-spliced the purple wire in order to extend the trigger wire to reach to the switch panel.
Is there a link for the air truck shown at 4:51?
Hey man how long did the whole project take you?
@francisngo
2 жыл бұрын
Without the research and diagram, the installation project took about 2-3 days. With research and diagram, about a week's worth of work.
Can you attached a link to the tray that you used. I’m looking up SD Off Road and I’m turning up with nothing.
@francisngo
Жыл бұрын
Contact Derek on his Instagram - instagram.com/sdoffroadmt
what's the manifold for? and do you need that?
@francisngo
10 ай бұрын
It's purpose is for install Air Lockers solenoids to the compressor. However, how it's being used here is as an extension and easier way to attach the air hose in the 4Runner engines bay.
Looks like a lot of work to remove the tray of you need to access the vehicles fuse pannel
@francisngo
Жыл бұрын
Yes it would but fortunately, I don't have to access the fuse panel often.
@AntonioClaudioMichael
Жыл бұрын
@@francisngo going to suck when a short to ground keeps blowing a fuse
You didn't show us that it works and if it has plenty of air pressure it's part of the video on KZread??
@francisngo
Жыл бұрын
Sorry I missed that part for the video but can say it works with plenty of air pressure. Have had it for over a year now with no issues.
@2006evolutionmr
5 ай бұрын
Thanks for the video, got everything you got as well. Only issue is when testing the Air Compressor before installing it , both air compressors isn’t working I here a clicking noise though, but if I unplug both compressors the fan does turn on. I thought I have a lemon ARB but I asked a shop and they told me I can’t run the Compressor to the switch pros that I have to run it to the battery. I’m not sure if I did something wrong.
New to the 5th gen and bought a ton of parts off the guy as well, including all of these. Exactly the video I needed after 4 days of searching. Will contact SD Off-road in the am to make it happen. Thanks so much for your time and effort!