3G TACOMA DIY : Installing an ARB Air Compressor : Under the Hood
I installed a bracket and on-board ARB Air Compressor under the hood of my 3G Toyota Tacoma! See how I did it all by myself...including the wiring...and IT WORKS!
I purchased the single ARB Compressor which was all I felt was needed for my needs.
I chose to purchase the GTFO Expedition - ARB Twin or Single Compressor Bracket for 2016 + Toyota Tacoma from ROGUE Off-Road ($120)
www.rogue-offroad.com/product...
I figured out the hard way to install the compressor onto the bracket BEFORE installing it at the location I chose. It will be very difficult to bolt on the compressor when the bracket is in place.
The wires were fairly easy once laid out.
Originally I was going to put the switch next to the compressor but because I needed to connect the fuse box under the dash, I felt it was better to put the switch in the dash.
I pushed the switch wires thru the firewall. If you go along side the rubber at this point, made sure you use something to protect the wires. The edge of the hole will eventually damage the wires.
Where I installed the switch, there is a need to use a Dremel to trim the inner part of the dash. If you look inside the hole, you will see the edge I am talking about. It is a simple task.
The fuse box is easy to access under the dash. You will need to make sure you have the mini adapters to make a single circuit into a double. Don't forget you will also need a second 5amp and 10amp mini fuse to make it work.
the 5amp is for the switch light. This light is a little bright for me and I am considering disconnecting this wire from the fuse box. I don't really need the light.
Hopefully, this video is helpful if you are considering this install. It took me a while but it was not hard if you take your time.
Now to clean up the wires.
Thank You for watching!
#natureszoom #dyi #aircompressors
Пікірлер: 64
Simplest and best ARB wiring explanation on KZread for those not running air lockers. Thanks!
I got the dual arb compressor and a 1 gallon air tank and the bracket I got holds both the tank and the compressor for the same passenger side location
Always cool to see what others are doing
@DigginSoCalOutdoorAdventures
11 ай бұрын
Thanks. This is one add on that has saved me along with a tire plug.
@AntonioClaudioMichael
11 ай бұрын
@@DigginSoCalOutdoorAdventures tire plugs always come in handy
I normally don’t comment on install videos but this one was short and to the point. I will be using as a reference when my arb arrives. Thanks
@DigginSoCalOutdoorAdventures
4 жыл бұрын
Thanks. It has worked out great for me. I am glad it will be helpful.
One of the more helpful install videos ive watched. Interested in seeing how you managed the wires aling firewall and up to battery. Planning on doing this install in the next week or so! Solid video!
@DigginSoCalOutdoorAdventures
3 жыл бұрын
Thanks....It has worked perfect and I am very satisfied with the results.
Thanks. Great video
@DigginSoCal
Жыл бұрын
You are welcome. It has worked out well
Thank you for your video, very helpful 👍
Great install
@DigginSoCalOutdoorAdventures
4 жыл бұрын
Thanks
appreciate the video, I know its been awhile, but in case you havent found solution for interior fuse box cover, Meso Custom sells one just for that scenario, probably have to set a notification for inventory, but its perfect
@DigginSoCalOutdoorAdventures
11 ай бұрын
Awesome. Thanks for the info. I will check it out
Great Idea! All you need now is a frother for your Latte's :)
@DigginSoCalOutdoorAdventures
4 жыл бұрын
If I could....I would have a coffee dispenser in the dash!
Thank you for going into detail on the wiring- it really saved my install. Seems like all the other folks doing install videos have s-pod units and they don't explain what each wire does.
@DigginSoCalOutdoorAdventures
4 жыл бұрын
Sweet. I am glad I could help. Initially, the fuse wires were a challenge. But, figured it out! Thank you very much for the comment.
@edgardorodriguez1314
3 жыл бұрын
@@DigginSoCalOutdoorAdventures I got an issue myself. I see you put two fuses onto the adapter... my compressor isn’t turning on. Could it be that I need both fuses per adapter?
@DigginSoCalOutdoorAdventures
3 жыл бұрын
@@edgardorodriguez1314 You do need two 10 amp mini fuses in the ignition fuse location where you connect the red/yellow wire or it will not turn on. The 5 amp is only for the switch light.
@edgardorodriguez1314
3 жыл бұрын
@@DigginSoCalOutdoorAdventures I got it to work!!!!
@DigginSoCalOutdoorAdventures
3 жыл бұрын
@@edgardorodriguez1314 Sweet. good
Awesome! Now... what are you going to put on the other half of that mount!?
Nice install
@DigginSoCalOutdoorAdventures
4 жыл бұрын
Thanks....learning a lot since I got this truck
@DigginSoCal
4 жыл бұрын
@@DigginSoCalOutdoorAdventures So what is next for your truck?
@DigginSoCalOutdoorAdventures
4 жыл бұрын
@@DigginSoCal Considering a lift/shock upgrade? but I just ordered a Safe Jack and need to complete camping gear first.
Great video and install. I have the same kit and used your video to guide me. Thanks for your work!
@DigginSoCalOutdoorAdventures
4 жыл бұрын
I am pleased I was able to help. I am going camping at the end of the month and will probably post a video of it being used along with a few other things. Cheers
I really appreciate your post. I will be installing a duel arb and the one thing I was worried about was the wiring process. If I Dont have a dremel tool can I hand sand the panel to fit the switch? Or sand the switch to fit the panel?
@DigginSoCalOutdoorAdventures
3 жыл бұрын
That is cool. I don't see why not...Just take your time so you don't remove too much.
Great video! Where did you get the fuse adapters? Do you have the link from where you got them? Thx.
@DigginSoCalOutdoorAdventures
3 жыл бұрын
Thank you very much...Here is a link to what I bought... www.amazon.com/gp/product/B07QMSGX8N/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1
Do you have to run those wires to the fuse panel under the dash? Or do you only do it if you want illumination on the switch?
@DigginSoCalOutdoorAdventures
3 жыл бұрын
One wire is for the switch light and the other is for the compressor to know your ignition is on. I could not get it to work without the one wire going to the ignition fuse under the dash. I am not sure if there is a way to bypass that and wire it into the main fuse box under the hood.
love the video, but where did you end up putting the relay at?
@DigginSoCalOutdoorAdventures
10 ай бұрын
Thank you... I zip tied it to the wire harness directly behind it and it has been good to go.
Hey man im having trouble installing the bracket arm, can you show that part or give some info of where exactly it goes
@DigginSoCalOutdoorAdventures
2 жыл бұрын
I had a really hard time too... it is the most difficult part of the install... I can try and take some photos of it if you want to send me an email....you can reach me at bill@digginsocal.com
viar makes a compressor that mounts on the vehicle.
@DigginSoCalOutdoorAdventures
4 жыл бұрын
I saw that. I should have been more specific. I was originally going to purchase the VIAIR 400P. In all fairness, I think either product mounted would be a good choice.
🌮
Did the fuse extenders come with the kit?
@DigginSoCalOutdoorAdventures
4 жыл бұрын
Fuse adapters do not come with the kit. I first went to an auto parts store and bought some only to find out the fuses I grew up with were to big. The ones for the tacoma are small and I bought them on Amazon.
@OVRCRWLR
4 жыл бұрын
@@DigginSoCalOutdoorAdventures link please? I'm about to do this same install and electronics are my weakness. I guess they don't supply them w the compressor because every truck fuse box is different???
@DigginSoCalOutdoorAdventures
4 жыл бұрын
@@OVRCRWLR Here is the kit I bought on Amazon...www.amazon.com/dp/B07QMSGX8N?psc=1&ref=ppx_pop_dt_b_product_details Just read details and make sure you need it. As long as you find mini adapters and one 5 & 10 amp fuses your GTG
@OVRCRWLR
4 жыл бұрын
@@DigginSoCalOutdoorAdventures i have a 2020 Tacoma so it should be the same as yours. Thank you for this video too. Many of the others don't show the wiring bit.
@DigginSoCalOutdoorAdventures
4 жыл бұрын
@@OVRCRWLR Yeah you should be fine. As long as they are mini adapters. I bought the regular ones at the auto store before I really looked. Thanks I appreciate the feedback.
thank you bruce lee
@DigginSoCalOutdoorAdventures
4 жыл бұрын
lol
Why doesn't anybody install it under the bed of the truck? Is that possible?
@DigginSoCalOutdoorAdventures
4 жыл бұрын
I did a lot of research and Saw many locations people have installed a compressor. I went under the hood for a couple reasons. I felt it was the best place when considering the wiring and it was a good location that I could easily reach. Other locations for me were up by the radiator or in the bed in the cut out compartment. I chose not to put it in the bed due to difficulty accessing it when the bed was packed up. I saw a truck with it under the bed and it was covered in dirt/mud. Also, his was more difficult to reach. In conclusion...it could technically be installed anywhere.
What's the year your tacoma
@DigginSoCalOutdoorAdventures
4 жыл бұрын
2019 TRD 4X4
How much should the t-connector be tightened? 🤔I don’t want to over tighten it.
@DigginSoCalOutdoorAdventures
Жыл бұрын
Actually this was my first and only time I have ever done this so I just went by feel. I don't have any specs on how much torque to use. sorry
You should get a spod or something be a lot cleaner
You need more Starbucks