I Built a Robot That Can Make me Rich
Ғылым және технология
Ever since I built my flattening jig and upgraded it with the gear rack, I knew that, eventually, I would automate it. The concept for that is also pretty simple. However, the execution provided a good amount of challenges. And that's what this video is about.
Support me here: www.patreon.com/mariushornber...
or support me through my Amazon wishlist: amzn.to/2QoQbhw
Follow me on Instagram: / marius.hornberger
Use the exclusive code "YTB930". Buy FlexiSpot E7 now for the best price!
You will get $30 off of an $500 order.
US: bit.ly/3tHS6Ti
CA: bit.ly/3rIASVC
Check out these videos:
Original Flattening Jig: • My Version of a Router...
Dining Table Build: • Dining Tabletop with C...
• Dining Table Base with...
Upgrading the Jig & Bed Build: • Homemade 10,000€ Bed |...
Shop Computer Arm: • Homemade PC Arm with S...
Enjoy the video!
I Built a Robot That Can Make me Rich: • I Built a Robot That C...
Пікірлер: 1 400
I had the idea for this jig and video for over a year. Glad I could finally get it done. Use the exclusive code "YTB930". Buy FlexiSpot E7 now for the best price! US: bit.ly/3tHS6Ti CA: bit.ly/3rIASVC
@daniellapain1576
7 ай бұрын
New to the channel, liked and subscribed. I love this idea the overall size almost matches industrial planer sizes and it wouldn't be too difficult to change it to do that. My real suggestion for your machine would be to build legs on it and build a sheet steel hopper underneath that leads to a garbage can. If you need it to push the shavings into the garbage can install a rumble motor on the hopper that activates when the router hits certain points of the process. Then you end up with pure clean large shavings useful for mulch or smoker.
@sweetlord5099
7 ай бұрын
Eventually you will run out of ways to do it wrong...
@jakWiize
7 ай бұрын
My dude, use a hair dryer on a label for 10-30 seconds and they'll come right off super clean.
@vs6703
7 ай бұрын
Danger button
@garnetsteen
7 ай бұрын
And now, an automated sanding machine!
OMG love the encoder ring with the limit switch! ... and "eventually though, you run out of ways to do it wrong"
I think this is one of my favorite videos you've ever done. It's got it all; woodworking, electronics, engineering, etc.
@Haderate
7 ай бұрын
The pneumatic tool changer was also pretty awesome.
@alextrezvy6889
2 ай бұрын
@@Haderatethanx for mention. Didn't know about it.
it would be cool to control he sweep speed based on how much current the router is using
@chrisis9030
7 ай бұрын
I think I was thinking the same thing, but in different words🤔
@T0tenkampf
7 ай бұрын
of course this isn't complicated enough for Matthias lol, that would be useful though.
@ppdan
7 ай бұрын
Not sure if it would work with this setup since the router slide would probably just start lifting instead of showing big power variations. Maybe measuring the vibrations on slide using a piezo sensor?
@chrisis9030
7 ай бұрын
@@T0tenkampf Well, I was wondering how Marius accounted for the wood hardness and Matthias translated the same thought into nerd language.
@King_Flippy_Nips
7 ай бұрын
Why not use a temperature sensor, the harder the material being cut the more friction so therefore more heat.
It´s just jaw dropping how much allround skill you have with designing, engeneering and programming... and filming. And editing! Such a cool video. Must have been a ton of work. Thanks for sharing!
@MariusHornberger
7 ай бұрын
4 long weeks of hard work
@OttoDidactic
6 ай бұрын
@MariusHornberger I'm hoping you will make jigs to swap to a mounted belt sander and random orbital sander in a future video
@NOMAD-qp3dd
6 ай бұрын
@@MariusHornbergervery entertaining! Well done on everything, the machine is awesome, the tables look beautiful, and the video was a fun watch! Sub'd! 👏👏👏
First time I’ve seen somebody talk through the lathe operations with callouts to the mechanical drawing- what a wonderful value-add to those unfamiliar with the process (like myself)!
@MariusHornberger
7 ай бұрын
Thanks. I think I should do that more often
@KeithOlson
7 ай бұрын
@@MariusHornberger Here's a software upgrade you can try: 1. For each run, have the router ping-pong back and forth a few times--while the main motor is off--so the Arduino knows how long it takes for the router to travel to the end stop and back. 2. Based on the width of the milling head and the calculated time, the speed of the main motor can be set so that it continuously moves the carriage along such that each time the router hits the home end stop, it has advanced (almost) the width of the milling head for the initial passes and (almost) 1/2 the width for the final ones. This slanting path will not only result in smoother movement of the carriage, but, for the last passes, each part of the board will be passed over twice, at two different angles, which should make for an even smoother surface. Does that sound reasonable?
@MegaDada1995
7 ай бұрын
@@KeithOlson Regarding the slant: The Fusion 360 "Pocket" tool path can do this already which doesn't really result in a smoother surface, however, depending on the material, it may help hide tool marks better.
@KeithOlson
7 ай бұрын
@@MegaDada1995 "... it may help hide tool marks better." That's what I was mainly thinking. (...and a drum-sander head to get everything shiny-smooth would also be pretty cool.)
@SetKat-Alex
7 ай бұрын
@@KeithOlson eh, I don't really know if it's worth the software complexity tbh
That's quite an inspiring quote: "Eventually you run out of ways of doing it wrong" :-)
“Eventually you run out of ways to do it wrong” I am going to use this line daily. Great build!
@tusharjamwal
3 ай бұрын
Sometimes it's because one of the ways proved fatal. Don't let that happen to you sir! xD I wish you success!
@omega_one1318
26 күн бұрын
It's a great line! If I remember correctly, Stuffmadehere said this line in one of his videos, so I'm guessing Marius is quoting him.
@stevenharder308
Күн бұрын
That line made me laugh out loud.
You are a true polymath...I am not sure if people can grasp the amount of knowledge you have, the ability to combine them in just a single project, and last but not least the amount of time invested to acquire it at such a young age. Your parents must be really proud.
@Arterexius
3 ай бұрын
There's not really anything such as a false polymath. A polymath is simply defined as a person who has mastered more than one field of work. What you may be referring to, are multipotentialites, who are also the only people who have any chance at ever becoming polymaths, since one must first develop multiple potentials before being able to master multiple fields.
I am astonished at how comprehensive this work is - right up to testing the air quality with reverse sticky tape. This is next level "thinking outside of the box" stuff. Speed of editing/presentation means there's nothing boring, and the humour is spot-on too. Honestly one of my favourite channels.
@elliespohr
7 ай бұрын
Sticky tape isn't going to show you the most harmful micro particulates that are actually the most dangerous for your lungs and nasal passages. He should purchase an actual air quality testing meter.
Blow hot air on the label before you try to lift it. A hair dryer or similar will work. It softens the label adhesive and the label comes off cleanly!
@AlainPilon
7 ай бұрын
If this works, you deserve a Nobel prize!
@michaelmaloney2803
7 ай бұрын
Genius.
@concolo
7 ай бұрын
Also oil helps with a lot of stickers. It still creates a little mess but it feels so much better than that hydrocarbon based stuff
@tarheels100
7 ай бұрын
@@concoloI know what you're saying, but FYI oil is a hydrocarbon too.
@pflegefachkraft7595
7 ай бұрын
Ikea labels on their “wood“ panels will disintegrate before the labels go. My solution is to add paint over whole surfaces
Sticker removal: Acetone works much better than paint thinner, but a heat gun, cricket lighter, or blowtorch will quickly soften the glue on any sticker. Hallo Marius wunderbär!
Beautifully crafted. It's so perfect for making desk tops with!
Marius, regarding the Arduino falsely registering electrical noise as button presses I suspect that either you didn't add a pull-down or pull-up resistor, or the values were too small. Try a 1K ohm resistor for this purpose, it should greatly remove any noise that you might encounter in your projects.
@PapaLurts
7 ай бұрын
arduinos are super sensitive so you absolutely need a pullup or pulldown resistor. I usually use 10k but I agree that with that much possible interference 1k might work better
@DRSDavidSoft
7 ай бұрын
@@aaakkk112 Yeah, but to my knowledge they only have an internal pull up. I suspect that Marius wired the limit switches between VCC and the input pin, in which case a pull down resistor is needed. Also, as @PapaLurts put it, the lower values work better for noisy environments like this case, the internal values are close to 20kΩ and 50kΩ ohms which is a bit high for this case. Note: Personally I use external pull up resistors even when I enable the internal ones, does anyone agree with this? Because using external ones you can adjust the value to your specific need.
@DRSDavidSoft
7 ай бұрын
@@aaakkk112 Exactly, also reminds me of when I started using Arduinos and microcontrollers in general. I exclusively tie the push buttons to GND now, but when I started tinkering with them, I used both positive and ground signals for this. I suspect that if Marius also used GND signal, there wouldn't be a noticeable interference. Additionally, there might be a issue with bouncing but I also suspect that he might use `delay()` to deal with that.
@louisfkoorts5590
7 ай бұрын
Wow, fun for the fans. 👍🏻
@dack42
7 ай бұрын
@@aaakkk112 Internal pull-ups are generally much weaker. For the ATMEGA 328P (Arduino Uno), it's around 34k. An external pull-up with a value of a few k ohms would greatly reduce the noise.
I really love this channel. Its the perfect balance of building stuff, engineering problems, electronics and scientific breakdowns. Great video, I honestly look forward to the next video.
This is a really wonderful mix of many different areas of work - machining, 3d printing, woodworking, and use of a microcontroller. Thank you for putting it up, it's inspiring.
As a fellow joiner/carpenter, it is an absolute joy watching your videos. From the woodworking and engineering all the way to the troubleshooting and reverse engineering perspectives! Great editing and humour. Keep up the brilliant work!
Suggestion for a new feature: Add a toggle button to switch between X-axis and Y-axis mode. Might be a little more efficient on long boards since it doesn't have to move X every few centimeter :D
@satibel
7 ай бұрын
Tbh with good encoders and probably more reduction on the y axis, x-y is also probably doable (i.e. move the y axis during the cut in a Z pattern, but the bottleneck is probably still mostly the speed at which you can cut with a gantry that's held together by gravity and hopes and dreams.
@larrybud
7 ай бұрын
I'm betting the quality of cut would be better too.
Your channel is the only one where I wouldn't even know where to start if I wanted to replicate your work. It is intimidating. You must have studied a lot of engineering. Incredible work, I love your videos.
@xl000
7 ай бұрын
This is DIY with expensive stuff bought with KZread money. I don't see any engineering here. Arduino is hobbyist electronics.
@randogame4438
7 ай бұрын
@@xl000 That's a pretty lame comment. He thought up and designed 3D parts to achieve various function, went through the complete troubleshooting and design failure analysis and made corrections. Where are your videos doing ANY of this?
@randogame4438
7 ай бұрын
It appears @x1000 deleted his comment. Good.
@crashkg
7 ай бұрын
There are trolls everywhere. They are just jealous of other people's successful projects. I just ignore them.@@randogame4438
@John.Flower.Productions
7 ай бұрын
@@randogame4438 @xl000 did not delete his comment. You or one of your fellow fragile snowflakes probably reported it because it hurt his/her/they/them's precious feelings. _For the record:_ @xl000's comment was a fairly accurate analysis of this video. That was quite a bit of _engineering_ and/or _incredible work_ to produce a plywood gear, mated to a windshield wiper motor. That said, he did put his logo on it; which everyone knows is the most important feature of any _robot._
I love how you talk through your thought process, process in action, troubleshooting, and various other crucial elements that many other creators gloss over, or don't even bother mentioning. Really loving your content. Keep it up!!
I've been watching you for years, I'm so happy for your ongoing success. You are a very inspirational speaker and exceptionally clever in your designs.
It's not often you see a sponsor spot that blends in cohesively with the actual content but this video is definitely one of those. 👍
That was a joy to watch Marius. Of course you get to keep the printer files for future spare part manufacture. Well done.
Did not know about you before. Just stumbled over this today. I am flashed away with everything. Such a detailed documentary on such a complex process. I think my beginners brain could only catch 15 % of all, but what it caught is burnt in. Thank you for showing this amazing project and journey
Hi Marius, I just have to write to tell you how fascinated I am in your ingenuity. The problems you solve, seemingly on the fly?, is just so impressive. You might investigate using optics for your encoders but wholly cow is this just an awesome video mixing wood working, robotics, electronics & automation in a project that solves real problem. I honestly believe if you ever started your own tool (or whatever) company, you'd be a force to be reckon with. Your name & videos, for me, are associated with extreme high quality & engineering. Prost von einem Bewunderer in den USA.
Very cool project, you outdid yourself once again!
As a mechanical engineer myself, I have amazing admiration for your design (and fabrication) skills! I've been watching you from the beginning and love your work. Thanks for sharing with us!
Love your camera work, especially around 27:00 where you are ripping and showing how the wood reacts to the release of internal tension. Just a great video. Thank you.
It's really cool to see the progression from a simple jig to a more complex automated tool. There is even a clear upgrade path to a full CNC router. Have you considered building a separate sled to automate the sanding part? Or would that not work? Great video as always!
Dude, you gone long way. From "the child with a saw" to one of best DIY channels on KZread! Awesome! And - can't wait collaboration with Blacktail Studio :D
Ever since I discovered your channel, I've been catching up on all your previous videos and looking forward to your next. There are two words that, for me, define your work, inspiring and intimidating. Your ability to go from idea to design to creating with an occasional bit of correcting is truly a work of art Plus your patience and calm in the face of obstacles is nothing short of amazing. Which brings me to the second word, intimidating. You make it seem so easy as you go through the processes that many times I ask myself, could I do likewise and sadly I must answer no. While I can make small simple things, your ability is almost out of this world though your humour at the oops moments does bring it back to earth. Thank you for continuing to share.
“Eventually you run out of ways to do it wrong” could be a maker’s motto.
Your best video yet. I love how you show problems and how you overcome them. And you hot glue tip to restrain resin pours - so simple but it will save me a lot of mucking about with origami folded masking tape!
@daveweber1331
7 ай бұрын
Yeah! I caught that one too - ingenious - to the point of annoyance!
I really appreciate your design and build process and how clearly you communicate it. It makes for very informative but still interesting videos. Thanks for all the work you put in and for sharing it. It’s very much appreciated.
The flatting rig is awesome, but also, you go above and beyond. The dust collection was also amazing. The well thought out controls are great too. e.g. limiting range of motion, manual control etc. very well thought out.
Love the machine and the slick and professional editing. The tables look fabulous.
Great video! Maybe a future upgrade could be attaching motors to the leveling feet as well and using wires that complete a circuit when they touch to automatically level the piece and make it parallel
@jml_53
7 ай бұрын
Nice idea, but I think using the crossed wires would be unreliable. It's just use a leveling sensor for that.
Unglaublich stark, Marius! Du vereinst wirklich viele Fähigkeiten in einem Projekt! Will nicht wissen, was du mit einer größeren Werkstatt zaubern würdest, aber ich bin mir sicher, dass wir das auch noch sehen werden! LG aus Hessen
@user-jg5ww4ez2d
4 ай бұрын
Scroll Grad durch die Kommentare um zu schauen, ob es noch jemanden aufregt dass die Schutzfolie auf dem kleinen Display noch drauf war😅 Hab die Ganze Zeit drauf gewartet dass er die abmacht
This is unbelievable! Thanks for this awesome video, I had a grin on my face many times watching! I really appreciate all the effort that goes into these videos and Im really happy you stay true to your style!
That was a captivating video. You're quite the talent and I liked how you included the parts where things didn't go as planned. A+
I would have probably added some rail or stop block even from the top side of the router to prevents it from lifting. Im afraid that if you set up incorrectly the feeds its gonna jump out on you. There is nothing preventing to lift the router jig. Also the result height might be uneven because of that.
Great build, great video. Thanks for not making a 1473 part videoseries out if it.
I did a similar resin pour for a knot recently, and that hot glue trick would have been so handy. Tape on the other side held fine, but it leaked out a lot on the top side.
It is so beautiful to see projects coming together like this. Your machine will probably make you a lot of money if you keep on making nice tables and it will give you more time to do whatever you want.
Brilliant - great content, great voice over and editing, and just absolutely fantastic how you have combined so many fields to get there.
Really a joy to watch. And wonderful results! Congratulations.
This is incredible. Kudos on the design, kudos on the craftsmanship, kudos on the engineering.
I always appreciate your engineering excellence in these projects. Because you and Matthias use your engineering skills towards different ends, for the most part, both channels are very interesting to watch without being repetitive. Both desktops are beautiful. I would definitely go for the walnut myself. I really like the added features of the desk system you chose, especially the cable management tray. I have an Uplift brand adjustable desk, and it did not come with cable management. I actually mounted a length of 2" split loom under the back edge of the desk for cable management. With the split loom, it is easy to add new cables, or remove cables for maintenance.
Awesome video! I really enjoy how you are able to design exactly to the requirement and save time/effort/money in doing so. The rough resolution encoder and simple limit switch direction change are things I never would have thought of. You should look into Precision Matthews benchtop mills, they're fairly affordable/compact and would serve you well to perform the operations your drill press/lathe can't handle.
Man this was awesome to watch! Love the automation with the wood working. The promotion is well done as well, it didn't feel boring.
Incredible amount of thought put into this REALLY COOL build
Very clever, great build. Inspirational.
fantastic work! Looks great! I could have used that when i made a workbench this past spring.
Alter Schwede, Marius - du bist noch so jung und hast schon soviel auf dem Kasten, meinen allergrößten Respekt. Ich denke mal da wird wohl auch mind. ein Maschinenbau Studium im Skill-Tree sein. Dank so pfiffigen jungen Leuten wie dir glaube ich, dass die Jugend noch nicht ganz verloren ist. Klasse 👏
You are a genius, your projects are always outstanding, the beauty in your work is that you also show your mistakes which indicates your constant improvements. Well done it’s a pleasure to watch your videos. I am very impressed, please continue.
Did some mechatronics with my workbench at home. Aluminium and wood is a good combo for strength & weight - for threads Aluminium rivets pressed into wood worked well. Nice project & informative presentation. Cheers.
Great video. You got an instant subscribe from me with it. I love your explanations and pace. You covered a long build without feeling like you were skipping steps or taking three days on a mini-series. If only I could build this that fast. 😀 I can see that I've got a lot of your videos to catch up on.
I love the problem solving in this project. Mixing wooden, metal, and 3d printed parts in the best way is not easy. Good job.
Really great video. I have an engineering background as well but then to see you use these skills like this is refreshing.
Great project. I'm a furniture/cabinet maker with a side interest in engineering. I often have ideas or concepts but struggle with the design stage. I would love to know a little more about your approach here. Keep up the amazing work, it is a great source of inspiration
Those tables look awesome! I love your automated flattening sled man. Brilliant 👏
Awesome design, I really like the quick disconnect for the router sled, very innovative.
This was a great video. Your knowledge of electronics really helped you build a quality machine. Thank you so much for posting this video
amazingly informative and interesting!! this makes one want to get into all of automation things from learning how to setup your equipment from bare bones even more interesting that CAD has sooooooooooooo many applications! i do not regret starting to learn CAD modeling on my own at all Good stuff Mathias!!
I enjoyed how I started to get "WOW, he did this!" from the first minutes and just felt a numb face by the end of the video because all you improvements did not want to stop.
Really cool project! Lots of work, but the end result is great. Thanks for the video! 👍
Such awesome dedication to quality design and performance!
Wow!!! This not only works, but looks so good! Those gears are fly!
Sir, you are a superb engineer. The effort you put into your projects along with your video work is world class. You have a very bright future ahead of you. Well done my friend.
Great project!! Thank you for sharing!
Nice build! I especially like the magnetic quick-change fastener. Well done.
Great job Marius! Love all the additional explanations.
This is unbelievably cool. Using a limit switch as an encoder is a brilliant idea. And unshielded wire seens to always be the root of the problem
Yes that! I hate label glue, It's even worse reusing some kinds of glass drink bottles. Perrier bottle labels fall off completely in water. Colorless bottles with clear colorless labels means you need a solvent.
Here is a tip for removing sticky paper labels. Use coking oil to saturate the label, then dish soap to dissolve the oil. The glue in the label will stick on the oil and the oil will be removed by the dish soap. Works like a charm, every time.
Marius - this is great - and I've been thinking about doing a CNC like this - open sourced and rack and pinion type - so that it is infinitely customizable and expandable - great work!!!!
Congratulations! Your perseverance has really paid off. Great job 👏
I love the precision and attention to detail that this guy has - so good!
Amazing amount of work for an amazing result. Your production quality also gets better all the time. Well done!
Stronger pullpup and some capacitors will help with EMI noise even without using shielded cables. Can be solved in software too by just measuring couple times and rejecting false pulses or giving some time-window when signal has to be active. Of course nothing wrong with using proper shielded cables. Makes it more industrial. Would be also nice to use mats unded the board too, add some rollers and springs so it forms some kind of conveyor belt and stays attached all the time. Gives you chip-protection for both sides. Great project anyways!
beautiful work, love your precise, elegant approach to design, subbed for more
Brilliant design and video Thanks for the quality content and inspiration!
This is literally, the highest quality youtube video I have ever seen. It earns a sub like and comment for that reason alone. Nevermind the fact that it is such a cool machine you built. Well done sir, well done. I wrote this comment at around 18 minutes into the video. Im editing this now that I have watched all of it. I enjoyed the last part as much as the first. crazy good.
@16:45 "Eventually though, you run out of ways to do it wrong" Should be the first page of every engineering text book. Back in the old days, we (well.....I ) used to go dumpster diving looking for the printout with the same class number. To see how someone solved a particular routine. LOL. This was such an outstanding video. And at the very end... the "goes to a.....friend" makes me think you have someone special (maybe?) If so, she's a lucky girl.
Marius, legendäres Video! Ich muss echt sagen, du bringst mich immer wieder zum Staunen! Du bist definitiv ein Vorbild für mich.
Love your work, Sir. Please keep up the great projects and videos.
Impressive work! Love your presentation too.
Großartig, ich hab zwar nix mit holzwerken zu tun aber deine videos sind immer eine freude zu schauen und entspannen auch, von der Großartigen ingenieursleistung ganz zu schweigen, mach weiter so👍😁
Outstanding project.... I learned lots of things watching this!
If you put a second rail along the bottom, you could attatch a blinds roller that when unrolled covers the entire base of the sled. Have the roller end fed through a door brush seal and branch off some of your vacuum system to have a port near the brush. Hook up another moter to the blind roller, and now you can roll up the base through the brush which pushes all the chips towards the new vacuum port. Self cleaning base!
I swear man, your ingenuity never ceases to amaze me. This is freakin awesome!
Amazing design and workmanship, great video
Great job on the slab flattening machine, and I really like the FlexiSpot standing desk system. I'm going to add the E7 Pro into a replacement desk for the corporate office.
Really impressive, build, engineering, sound, video editing, artisan ship - you name it.
Top tip from Crimson Guitars. If you sand it while the oil is still wet, it will form a sort of sludge that acts like a grain filler for an ultra smooth finish.
For a first Arduino project that is advanced. Mechatronics, precision movements, electrical noise cancellation, manual mode input system, audio feedback and step down voltage conversion. Great job.
@MariusHornberger
7 ай бұрын
Well, technically I made an LED blink first ;)
I love to follow along and se how competent this young gentleman becomes over time. when i started to follow Marius he was just a kid :)
I need to build a project very similar to this. Thank you for the efforts.
Totally agree about the sticky labels. Great video.
Excellent engineering and design!