I have a hyundai h1, it can't start after changing the cylinder head gasket，I refer to this video, the problem is finally solved, thank you

Thanks for this info. My Captiva has this exact problem and two different motor mechanics have not been able to figure out a solution.

Thank you, your video help me to solve my problem, hyundai grand starex now back on the road.

Awesome been Trying to get my Holden Captiva going after checking the timing chain

thanks to you, your video help me start my car after put on new injectors, specially step 10 works very well. once again thank you very much

@gettingitdone1

2 жыл бұрын

Glad we could help. 😊

@malfamilys9122

2 жыл бұрын

@@gettingitdone1 plasure to you repaly, i need help , i have a i20 1.1crdi 2013 car has a Engine oil increase and increase and blue smoke on the hill. please give a idea tips .thanks

@gettingitdone1

2 жыл бұрын

@@malfamilys9122 so first question os does it have a DPF? The increasing oil level is usually caused by over fueling. Often that is caused by the vehicle being unable to regen the DPF. It keeps trying, which results in excessive amounts of fuel entering the cylinders and making its way into the sump. If it continues it could cause serious engine damage. I would advise taking it to a good mechanic or diesel specialist to have the DPF checked. If it doesn't have a DPF it could be a fault with the injectors themselves.

Awesome video. But I did try this a couple of times and could not get any fuel mist from the glow plug ports, so I ended up sending the injectors away to get primed so hopefully I can get it running

@gettingitdone1

Жыл бұрын

Oh that unfortunate it didn't work for you, they can be a real issue once they're locked up. Just make sure you follow the procedure when you put them back in. Otherwise they could lock up again.

Hi, I have follow all the steps it's a 4cylinder car with Delphi injectors, fuel pump has 2 couplers/electric connection s. I don't know which one should be disconnected but I tried with one one solenoid, then both together off. But car doesn't start. I suspect injectors locked but when I use scan tool and do activation test injectors activate and then if I crank car starts for 1 second. What could be wrong? Intially I had tried bleeding with injectors connected. But then I follow the procedure shown in the video but no success. Scan tool can test the injectors and apparently they are working

I have a no starter VW Crafter 2.0 tdi and unplugging the valve from HPFP don't seems to raise the pressure for some reason. I suspect that there might be some other system that limits the pressure too...

@gettingitdone1

Ай бұрын

Ok another trick we have used on some vehicles, it's not ideal sometimes a last resort (I take no responsibility for any damage 😆). Is to use some engine start (ether) spray, to get it to fire, that's sometimes enough to get them going, it will diesel knock while trying to run on ether, then clear when the diesel comes through.

If you try to start you cat with the injections plugged in will this damage them

If you got these injectors you can open the pipes.. start .. wait for diesel .. stop cranking ant the tightening everything op and pull the rail pressure sensor. It opens up the full pressure of 600 bar leave the car running for 30 second put it out putt everything back .. should be good .. did it this weekend and get the tip from Hyundai technician them shelves

@gettingitdone1

Жыл бұрын

You've just left a comment basically explaining what's shown in the video 😆.

It’s with my Toyota Matrix 2003 if I drive in the feeeway it never turns off and goes fast no problems but when I go in stop and go traffic the oil light comes on and car turns off what do you think it is ?

@gettingitdone1

3 жыл бұрын

Could be lots of things, does it just stall, like it won’t idle or idles too low?

I get Hyundai h1 2008 injectors didn't get power .same one can help me

Thank you for your video iv done all like you said engine just turns over still no start can you please help

@firatramadan6543

7 ай бұрын

Sorry my car is a 2012 Hyundai i800

@gettingitdone1

7 ай бұрын

What was the cause of your problem? Was something done with the fuel system?

If you have tried to start your car with your injector plugged it will this damage them

@gettingitdone1

2 жыл бұрын

Most of the team they will just get jammed up. Following this procedure should allow you to free them up again.

Hey mate I just changed my copper washers on my iload injectors due to them leaking! I have put it all back together and now won’t start it cranks and gets close to starting when I put the peddle down but won’t start

@gettingitdone1

Жыл бұрын

Follow the steps in the video to bleed the system properly. Theses injectors are a real problem to bleed but by following these steps you should get there.

@bextabeats3368

Жыл бұрын

@@gettingitdone1 where is that solenoid we need to unplug I couldn’t see it clearly in the video. Thanks for the reply

@gettingitdone1

Жыл бұрын

So at 3:05 in the video looking down the back of the high pressure fuel pump. That steel cap that kind of looks like the end of a wiper motor, will have a plug going into it. That's the one to disconnect.

@bextabeats3368

Жыл бұрын

@@gettingitdone1 hey mate I can’t find that motor mine is like a flat circle pump

@gettingitdone1

Жыл бұрын

@@bextabeats3368 do your injectors look the same as the ones shown in the video?

I have ah problem

I ha e a problem