This video helped me find a problem with my charging wire and saved me hundreds of dollars. Thanks!!

Can we give this man a Nobel prize please! 🎉🎉🎉

Seriously, thank you! Found the little plug was melted under the mower. On tip, get some test cables with crocodile clips, can then hook up mower to charging station and have it upside down to poke multimeter into various plugs! Thanks again!

Thank you for the videos. You just save me so much time, energy and money.

@RoboticMowerServices

Жыл бұрын

Awesome to hear! Thanks for commenting

Thank you very much. Very informative. I managed to fix my charger and the automower is charging now. Appreciate your help.

@RoboticMowerServices

2 ай бұрын

Awesome! Glad we could help

I found the video very helpful thanks. I hadn’t switched on the power switch on the automower itself

@RoboticMowerServices

Жыл бұрын

You're definitely not the first person to miss that

Hey buddy, thanks so much for the video. It's very helpful. I'm dealing with an issue that says my charging station is blocked. It's actually finding the station just fine. It's hitting the charging contacts properly. I think I'm going to find that there is a problem with the charging contact plug that you showed around 11:49.

I ordered both the harness and charging plates. When I first accessed the harness, it had a small bubble and wouldn't come apart. So I figured that was it. However, when I changed the charging plates, I also found that one of those connections had corroded to failure and was no longer connected. Needless to say, it was good to address it all. Everything is charging now and appears normal.

@RoboticMowerServices

9 ай бұрын

That is the best way to do it. Replace both parts at the same time

Thanks a lot, than was very usefull! Red cable was cut at the connector attachment Batterry is fullt empty, hope it can recover from that state.

How many amps should it be charging at? Mine charges at about 1.7 a for about twenty minutes and then it begins to drop gradually to zero and it doesn't charge after and doesn't leave the charger.

Hi there my info is saying 20v Charg lvl -1 Charg 6ma Temp. 9,6 Capacity 2600mah Has been charging 2days now with nothing happening. Is my battery dead or? Have checked the overheating cabel thing. And cleand charging ports

Very helpful thanks. My robomower though is running out of charge before returning to the charge station, it doesn’t seem to know when it’s battery is run down.

@RoboticMowerServices

Жыл бұрын

Have you tried adjusting your "Find Charging Station" settings? Here is a video explaining these settings. kzread.info/dash/bejne/aX2mza2Rnc-peLg.html

@astronomicaltalk5708

Жыл бұрын

@@RoboticMowerServices Thanks for the tip. After watching your video I was able to check the charge (0 key), I then noticed that the Robot had gone to ‘manual’ so just mowed until it ran out of charge. I’ve put it back to Auto and it now runs properly.

@RoboticMowerServices

Жыл бұрын

Glad you got it figured out. We've seen a lot of people over the years have that issue because they mistake the secondary area setting for the second zone that hey set up in the mowing area

Hey buddy I've a power that go 21.6 V as output but in my charging plate for my automower 305 I see 21.2 V. Automower is saying that is charging but in real it's not. Is the Voltage correct? What could I check? I've changed my battery 1 year ago and till now was working perfectly

thanks good video

@RoboticMowerServices

Жыл бұрын

You're welcome

Thank you for a great video. In the last couple of days I had a problem with charging my 315x. It happened two times that the mower returned to the base but after couple of minutes returned a little bit back and stopped in front of the base with "charging system problem" error. At first I thought that power adapter is gone, but after watching your video I checked all the steps and find out that voltage at the base is correct (28V) but when I manually plug in the mower the voltage on the base pins is still 28V (and not 18V as you explained in the video). In the menu is visible that mower is not charging since is shows Current -143mA. After that I switched the mower off and then back on (as the app suggested) and it started charging with Current ~1100mA. I suppose that the wiring is fine and that the problem could be the battery since it has 6530 charging cycles. What are your thoughts on this? Thank you very much for your help.

@baltazar888

Ай бұрын

I got this error again the same day I wrote this comment. After that I checked again everything and noticed that the cable which goes inside the mower is bend by 90°just after the connector. I straightened it by hand and put it back inside and for now is working couple of days without any problem. Maybe there was just a minor connection problem with that cable.

Hi. Great video. I've got the problem of The mower entering, then making a tone and then 2 seconds later making the disconnected tone shown a 7:20. The led goes off for a minute. I opened up the charging station took out the board and cleaned it. Everything else looks OK. But the same problem is happening. What else could it be? Is it definitely in the station or could it. somethibg inside the mower? The voltage on the connector s is correct. Thanks.

@owenbrady1771

Жыл бұрын

Just to follow up... I eventually tracked down the solution to this problem. It was the cable between the transformer and the charging station. I'm not sure what was wrong with it but when I switched in a new cable everything was back to normal. So the error of the green light turning off to no light as shown at 7:20 Can also actually be the power cable for any others that are looking for solutions.

Hi. Great video. I just noticed that when I put my 310 in the charger for this season it says charging, but when I locked at in in the app it shows that it actually drains. It went down from 13% to 12% to 11%. Then I jerked it out. Now after looking at this I measured things and found out that the harness shows 6,5 volts. Took it apart and measured 27,5 volt at the black and red on the cable at 5:08 minutes in this video. Looking at the harness and cables i could find no fault so I decided to try and measure at the connector at the top off the circuitboard that connects to the cable and I got 6,5 volts there. Faulty board on the charging station?

@RoboticMowerServices

2 ай бұрын

It could be a number of different things causing the issue. But the only way to narrow it down is by doing some resistance testing.

@JahaJaho

2 ай бұрын

@@RoboticMowerServices I did your testing and found out that it was 27.5 volt at the end of the cable going into the board and then 6,5v of the connector on the board goin out from the board which is the only step that was not in your video. That makes it logical to assume the circuitboard. Looking at the board it looks clean and all, but I guss it could still be broken...

@RoboticMowerServices

2 ай бұрын

@@JahaJaho Here's another video with info that will help narrow down the issue. kzread.info/dash/bejne/p3iYt9CLj9Wvcag.html

@JahaJaho

2 ай бұрын

@@RoboticMowerServices I managed to borrow power transformer from another Husqvarna user in the neighbourhood and with that transformer it worked. So now I know what the problem was.

Hi guys.. Just found your youtube channel, and i was trying to figure out what is wrong with my mower. I have a Husqvarne 315, and over the winter my battery has gone empty, when i came to the charging station it was blinking green, and when i put in the mower, the power button on the mower started blinking green, but it's not charging, have you guys seen that fault before???

Hi great video. I have a negative current on my charge, what could be cause of that

@gunterotte

3 ай бұрын

Hi, have the same problem. Negative current while it is supposed to be charging, but it's not. Did you find the cause? Thanks!

you're the best! thank you.

My chargin station shows 27.5V. Is that ok?

I had a software and hardware update done to mine last year around this time. Ever since I got it back it hasn't been the same. What it does now is goes out to mow, returns to charge, back out to mow, but then at the end of that charge cycle I get an error message on the app saying "charging system problem". Has anyone else experienced this?

@RoboticMowerServices

Жыл бұрын

Check out this video: kzread.info/dash/bejne/h6yT3NZtiJSpdrg.html BUT now instead of replacing the main board like mentioned in this video, get the software updated to the newest version which will solve this issue if everything else is functioning properly.

@Texastomfoolery

Жыл бұрын

@@RoboticMowerServices thank you. Husqvarna did send me all the new harnesses and charge plate assembly which did not help the problem. I will take it in to the dealer again for the latest update as I said before ever since I had the last update it's never been the same.

I have info current -12 mA what Can Bé thé Reson