Thank you, i’ll be trying this on my new headers tomorrow!

i just finished putting mine on, my forearms are dead but it was worth it

مشكورين اخوانا الاجانب

Thank you for sharing this 🙏🏼

I used high temp silicone at the tip of the end of the wrap to keep it from becoming undone.

@Ski.the.slayer

Жыл бұрын

How has it held up with the silicone. Did it give it a clean look?

@gonzalezeduardo28

Жыл бұрын

@@Ski.the.slayer the silicone became crispy, but the weave has not come undone.

always start from the bottom going up. that way the seam is beneath to the next seam going up. that keeps the water out.

For clarity purposes you should of said sewn edge exposed. That way regaurdless of direction or facing it would be clear what to do

All I can say is I wish I used gloves

@salomonkarr7917

2 жыл бұрын

😂

@vitkubal273

10 ай бұрын

😂😂😂

@jamesflores1146

4 ай бұрын

Savage 😂🤣😂

can such wrap reduce resonate?

why you need sawn edge to the collector?

Use barium coat wrap.

Well, turns out I did my one pipe completely wrong, looks like I'll be redoing it tomorrow and hopefully it goes a lot better. I started at the flange and not the collector, not sure what side of the wrap is where, didnt fold it over at all before my start, I pulled the entire roll through every time so I didnt measure it out, I'm pretty sure I overlapped way too much and needless to say, I'm gonna probably need more ties

is this doable when the manifold is mounted? my studs are very rusted and dont really want to undo it

@DriveTuneMedia

3 жыл бұрын

Depends on the header, probably doable, if you're patient....

Why has no one mentioned the smoking? Is that normal? Also can you use this in place of a heat shield?

@DriveTuneMedia

2 жыл бұрын

They smoke for the first few heat cycles. Yeah, I think you can use them instead of a heat shield.

is that made of painted/tinted fiberglass +

@DriveTuneMedia

3 жыл бұрын

crushed lava rock is the main material.

How much ft do I need for those headers ?? Is 100ft enough ??

@DriveTuneMedia

3 жыл бұрын

Here is a calculator for exhaust wrap www.designengineering.com/calculator/

silly question: What would be the weight gain for such a wrap?

@DriveTuneMedia

3 жыл бұрын

Minimal. DEI "Titanium" is very light. Exact numbers I don't have but it's lighter than normal fiberglass wraps.

@HondaAccordPerformance

2 жыл бұрын

@@DriveTuneMedia I’m worried that I might damage my headers I used a lot of overlap like 1” because I used the 2 inch wrap on mine I might of over did it. Should I remove the headers and rewrap them?

I have a cover on my manifold. How should I remove it?

@skyty0

3 жыл бұрын

A little late, but... Assuming that you have a stock header, that is a heatshield. It does the same thing as a wrap. Do not remove it lol

@thatoneintrovert9618

3 жыл бұрын

@@skyty0 I'm assuming the entire manifold is plastic. I have a 2012 Fiesta so I don't know if the intake manifold is completely plastic or it's a heat shield like you said.

This should keep the heat down in the engine bay?

@kino266

2 жыл бұрын

It will help, but if your engine is overheating on normal riding and normal weather, there are problems that wont be solved with exhaust wrap. It could help a bit when you have hot weather and are driving in traffic all the time

So you don’t need to wet it first?

@DriveTuneMedia

6 ай бұрын

Genuine DEI Titanium is very flexible without water.

Can u wrap headers that are heat coated

@pg24mvp74

4 жыл бұрын

If they’re ceramic coated I wouldn’t bother wrapping again

@Motleymick

3 жыл бұрын

@@pg24mvp74 But why not? Wrapped headers looks so cool. And it's cheap to do.

@azegulstarrider9675

3 жыл бұрын

You can. Some people do.

I watched hoping to see how to start the wrap. Both times you neglected to finish showing the beginning

@TonyTheTruckGuy

24 күн бұрын

Are you blind? 1:10…

What was the screwdriver for?

@CamboSlice-

2 күн бұрын

great question.

Those metal ties dont stay tight at all....they're worthless

@Boofedit

4 жыл бұрын

TheShangralaaaa17 after 12 drives or so the heat should’ve solidified the wrap into place anyway?

I learn one thing wrapping my headers WEAR GLOVES .

@polasnoob

3 жыл бұрын

i just get itchy right now 💁🤦 i feel regret

@slicktop2jz855

3 жыл бұрын

Exactly! My hands are a mess.

@polasnoob

3 жыл бұрын

@@slicktop2jz855 😭😭😭✋ at first i thought it just like a normal cloth

@andyroo3022

Жыл бұрын

Ha, I had a practice run of one of my Beetle J pipes last night. Until I read this I was wondering last night why my hands were itchy. I thought that only happened with fibreglass.

will the wrap lead to rusting of pipe?

@DriveTuneMedia

8 жыл бұрын

Hi., If its mild steel, yes. Stainless does not rust. Should not be used on Titianium exhausts because they tend to have very thin walls.

@nyinfamous2k2

7 жыл бұрын

how about if the pipes are painted with high temp paint first before wrapping them? would that cause or help any rusting issues? thanks

@firgaso

6 жыл бұрын

StreetandCircuit o

@hyp3MC

5 жыл бұрын

nyinfamous2k2 I’m curious in this as well.

@ReaDKingS

5 жыл бұрын

Yes, because it retains water and the dirt and grime from the road. Look at the pipe he is wrapping. Ir was wrapped at least once before... looks like the wrap stained the exhaust... you should change the wraps every 6 months or so.

where is the titanium? is that basalt?

@DriveTuneMedia

5 жыл бұрын

Hi Jose. Yes its Basalt. Titanium is the name of the product, does not refer to the materials

@Motleymick

3 жыл бұрын

@@DriveTuneMedia That's Confusing. I bet they did that as a marketing trick.

@CamboSlice-

2 күн бұрын

@@Motleymick yeah total bs why would you call it titanium in the first 10 seconds of the video and say that it doesnt need wetted down like fiberglass wraps, because "this wrap is titanium" lmao

Why wrap up to the head when you can wrap down to the tip and ti will look cleaner 🤦🏿🤦🏿🤦🏿🤦🏿🤦🏿

And now...simply wait 6 months and replace entire exhaust side of the engine!

@MaRkiLLeR666

4 жыл бұрын

Why?

@Boofedit

4 жыл бұрын

MaRkiLLeR666 in my experience, heat insulating wraps do more damage than good in the long run if you live in high humidity areas, cause early rusting and corrosion, weakens the metal. I get it though, hotter gas flows better, less heat dispersion in the engine bay, seems ideal but for most geographic locations in the Southern Hemisphere it’s more than un ideal, hope that clears up my reply :)

@vally6853

3 жыл бұрын

themusicmastera380 gotta spray the wrap with silicone to deter water

@bulbazoth6473

10 ай бұрын

titanium doesnt rust@@Boofedit

@Boofedit

10 ай бұрын

does corrode though! @@bulbazoth6473

And now you can proudly watch as your headers are trashed by heat and accelerated rust.

@deathtoliberals7843

4 жыл бұрын

Headers are cheap,compared to damage headers do. We couldn’t keep a starter from burning up,with heat wrap. Headers just get too hot ,under a hood.

@DL101ca

3 жыл бұрын

@@deathtoliberals7843 don't wrap the headers, insulate the starter.

@michaelsnyder5773

3 жыл бұрын

Just get better headers that can take it like stainless and use high temp header primer 3 years on beating on it and still whole.