Thanks. My washer is getting repaired and this was what they put was wrong with it. I wanted to see what it was and how it was done... This was alot of work. Great video.

Thank you! I, a 42 year old women, was able to replace this myself!

@appliancepartspros

2 ай бұрын

You're welcome!

Thanks for this. I have a Maytag that the bearings are howling when it goes into spin. Washer is just under 5 years old. My old Kenmore lasted 30 years. All new appliances are disposable garbage now.

@patriciamariemitchel

8 ай бұрын

I would say, stick with Whirlpool if they hadn't bought out Maytag. I saw a new One n Done at Lowe's yesterday for 2600 dollars. It eats its own exhaust. 👀 That's going to be a nightmare on many levels. 👀☺️

@richardthompson6366

7 ай бұрын

Kenmore had the best stuff, my Kenmore washer and dryer are around 20 yrs old and have only had minor issues.

@JohanSalvattore

7 ай бұрын

Maytag is usually decent, mine is about 10 years old and the teeth on the gear case are stripped

I've had all the things you mention go bad with my Whirlpool washer in 7 years.

One the most important part of how use car jack to get to inner tub off isn't shown. I used a simple spin car jack , with a strap hold down on another block of wood, a screw driver to spin the jack. The other piece of wood needs to be on the gear case drive shaft so the jack pushes the tub off.

Perfect video. Thank you!

@appliancepartspros

8 ай бұрын

You are welcome!

I Love this video shows how to replace dang near everything on the machine. Have you got a video on replacing the controls and lid switch along with diagnostics? Thanks -pawpaw

Thanks for diy appreciate

Good work!

Mine is just the shaft is damaged but so far it looks like I have to change this whole gearcase. I have a Whirlpool WTW5000DW2

@appliancepartspros

11 ай бұрын

Unfortunately, Whirlpool doesn't sell the shaft as a standalone part. It is part of the gearcase assembly.

@spareamintz8708

11 ай бұрын

@@appliancepartspros I figured so 😔

I am installing the same washer gear case and i will like to know if you have to grease the tub seal or its already with grease. the washer gear case had the tub seal already installed so i have to grease it or not. tk

Brasil SP, ..... técnico particular

Bravo 👏🏻

How did you keep the tub still while you were putting the gear case in?

How much space should be between the gear case and the basket after tightening the bolts?

Fuck...I'm just gonna take monday off for this lol

Thank you!

@appliancepartspros

7 ай бұрын

You are welcome!

Good video ,i love it,very educative,keep posting

@appliancepartspros

10 ай бұрын

You are very welcome!

Can these gear cases be rebuilt? IE: just replace bearings?

My four bolt 🔩 holes on the gear tranny don't sit flush with the plastic washer tub holes. The back ones are farther away. Is this normal?

just can't get the top off on whirlpool no hinge screws on the back and putty knife under front don't work.

hey! any reason for the inner tub to rub against the outer tub?

@ogrish76

Жыл бұрын

Impossible.

@chrisdominguez3780

Жыл бұрын

Warped basket

@richardthompson6366

7 ай бұрын

Could be worn guides for the tub maybe?

I dropped a screw down the washer and had to take out the inner basket. using the piece of wood helped but my God did it suck lol

Also the ring is bigger than the hole in the tub ...

Is it necessary to remove the basket in order to do the repair? I’m trying to figure a legitimate reason why but it seems like it’s not necessary when I watched the entire video.

@appliancepartspros

8 ай бұрын

Our videos are to give you a general idea on how to do the repair. If you are able to remove the gear case without having to remove the basket that is good. If you want to provide your model number we can look into this for you.

@KINGRG1

8 ай бұрын

@@appliancepartsprossure thank you. Model # MVWX655DW1

@JohanSalvattore

7 ай бұрын

I was wondering the same thing.

@JohanSalvattore

7 ай бұрын

⁠@@appliancepartsprosif you can help, that would be awesome, this is my model MVWX655DW1 (maytag)

If the basket is thumping, is it ever the case that the screw on the agitator is loose?

@appliancepartspros

3 ай бұрын

When is it making the thumping noise? What is the model number of your washer? Have you seen any error codes?

@davidbrandel4128

3 ай бұрын

@@appliancepartspros I replaced the stabilizer rods and it still shakes a little during spin cycles but doesn’t walk across the floor.

Why tf are steel shaft splines worn flush against a plastic/fiber drive hub?! Transmission Part is $160 + new drive hub $25 + ~$20 shipping = A $205 repair New washer is $514. This failed on my machine in 3 years. Expectation is another 3 years to repeat failure. A disposable washer. Annual cost = $171/yr to own this product ($14.50/month). Not a terrible cost, but factor in your time & labor too! Don't expect "10 years" Lol.

😊 k ,ap😊

One of the worst designed washers in history. Transmission is not service-able. transmission doesn't last. washer has bad lid lock system that's also not service-able. Control board on these washers fail consistently (used cheap capacitors) and also not service-able. washer was meant to buy and throw away. NOT ACCEPTABLE - never buy whirlpool again.

@RG-gt8fs

Жыл бұрын

They are all disposable garbage now with plastic parts and nothing serviceable.