Thank you so much for taking the time to make all these videos, learning alot from you! There really isn't any other channel with this amount of detail and production. Keep up the amazing work!

@GarageNoise

7 сағат бұрын

Appreciate the support! It's not easy ,without the support of people like you I may have stopped a while ago.

Tri coat whites are the most forgiving. Iv ran the pearl coat edge to edge many times on the newer Hyundais and always get a dead solid match. Good video man 🎉

@GarageNoise

8 күн бұрын

Thanks brother! Yeah, never had much trouble with pearl white as long as the base is right.

Great tutorial! Learning how to spot paint at home with a small compressor and LVLP paint gun is super handy. We sent you an email, take a look.

Tulsa that's awesome. I was just over there yesterday. Delivered in Cleveland, Sand Hill, & Glenpool. Then I picked up in Jenks before heading off to Indianola MS I pull out of Henryetta and Muskogee from time to time to.

@GarageNoise

10 күн бұрын

👍

Thanks again Chris . I've been doing paint work for 30 years. Never miss one of Your videos. 😁

@GarageNoise

13 күн бұрын

That's awesome! Thank you , appreciate the support

Thank you for explaining the attention to detail.!! 🔥💯👏👏👏👏👏

@GarageNoise

10 күн бұрын

No problem!! Thanks for the comment and support!

I have been following you for a while and have bought pretty much all the equipment that you suggested and it helped a lot. My question is for FC710 & FC720 dieback. The paint lays down like glass but couple of hours later the gloss is not there anymore.

@GarageNoise

11 күн бұрын

Die back is typically from waiting too long in-between coats of clear. It's funny I got some today because it's so hot 99° the first coat of clear cures so quickly. In hot temps you may only need to wait a minute before you apply the second coat.

@acesnyc

8 күн бұрын

I will try that and update usually I am waiting minimum 10 minutes before the 2nd coat.

Great job. I agree this is a great setup for diyer. I bought one of these guns to just try. I I have Iwata 400 for main gun but this is a good gun for the price. Great video🙂

Am I understanding that you sanded the original clear coat over the top through the A-pillar? I made so many mistakes on my old RAV4 that I might just be able to fix ‘em after watching this video. Thanks, Chris!

@GarageNoise

13 күн бұрын

Yes with 600, appreciate the support!

Maaco have this man train your technicians …TRAINING SEMINAR

@GarageNoise

16 күн бұрын

👍

Nice job looking good 👍

@GarageNoise

10 күн бұрын

Thanks 👍

I never understood spot panel clearcoats, i cleared a whole jeep with that same product... thats what SW gave me back then about 4 yrs ago and i based it with their dimensions, sprayed with hvlp and a 6 gal pancake compressor... the color sanding the orange peel was brutal

@GarageNoise

16 күн бұрын

It just dries a bit quicker. This buff a bit better when your on a deadline the fc720 overall clear flows a bit better, it just takes more time to gas out before it's ready to buff.

@bassdaze

16 күн бұрын

@GarageNoise thx for the reply and clearing that up🤣... think im gonna get that upol clear also, i have my sons truck and mine that needs rockers so gonna paint them complete... been watching your channel keep up the good work, most informative content out there imo

Hey Chris, another great teaching video from you. I was wondering if you have a filtration system or exhaust system in your shop since I notice you paint in the open. I’m a new painter and Im contemplating it for my shop

Hi Chris can you please advise me on inferred heater ?

@GarageNoise

8 күн бұрын

This is the one I picked up. It made by Vevor I have some of their other tools and they seem pretty good. I can't speak of its durability I pick it up last fall, but it's reasonable priced. Hope this helps appreciate the support! amzn.to/4bmklr0

I was thinking about getting that compressor but they also sell one that's smaller with the same 4.5 SCFM on it. It's only 10 gallons. I would assume that would also work with the LVLP sprayer without fluctuations as well then right?

Hi Chris, That looks awesome! One can see the pearl in certain lighting. One note. The link to the 3m face mask does not work.

How do you like this clear over the Upol?

Chris do you have a video using this gun with silver or gold metallic? thanks much, Phillip Hall

@GarageNoise

13 күн бұрын

Haven't sprayed silver with it yet, but I'm sure I will.

@PhillipHall01

13 күн бұрын

@@GarageNoise Thanks!

Hi Chris, a superb finish from what is a budget gun which is as you say a good gun and compressor for the home user. I think all these guns that are coming out lately that spray fairly well are all based on the R500 setup which is not a bad thing🙏👍John UK

Tank’s teacher Chris

@GarageNoise

13 күн бұрын

👍

Hey Chris; Quick question : Do you use a flex agent in your paint/clear when painting a bumper pad, or do folks just not do that any more ? BTW, I'm knee deep in restoring my old (one owner, bought it new) 1989 Olds Toronado. It's completely stripped back to metal, and waiting for low humidity day to shoot epoxy primer on it. All the plastic parrts will be prepped and painted afterwards.

how do fix a run like that? let it dry and sand it and start over? or.. do you have a better solution to it?

@GarageNoise

13 күн бұрын

I sanded it out and It was perfect but that doesn't always happen . Next time I'll make a video on how to fix it. I do have some on the channel.

@dsimms6

13 күн бұрын

@@GarageNoise oh you do? cool, I'll look for them. This is a great channel.

I hate it when everything is going good until the end. lol Good job. Looks like you have plenty paint left from the pint. What do you do with all the extra paint?

Hey Chris…first off love your videos, so helpful. I have a question though. When you spray I know you try to maintain a factory orange peel. How do you remove dirt nibs without that spot looking like you sanded and buffed it? Can you maybe add this to one of you videos?

@GarageNoise

16 күн бұрын

Yes I can, if your peel is minimal you can do it fairly easy. If you have excessive peel the you need to color sand and buff the panel. I can do a demo tho

@socalstangman4655

15 күн бұрын

@@GarageNoise that would be awesome. Thank you

Hey Chris the shirts you sent me. My mailbox got broken into they stole my mail. And the shirts out of the parcel locker. Was looking forward to trying on the shirts. I'll try to buy two more nexted month. Hopefully by then my mailbox will be repaired.

@GarageNoise

10 күн бұрын

What's your name?

@shugg0517

9 күн бұрын

Tony Mcfarlan