Thanks again for a great video Kirk. It helped me a lot today when I replaced my grips on my 2002 K1200rs.

Just bought them. Thanks for the tip. I have a 2002 1150r and my grips are totally melted. The grips in Canada are 175 dollars each. I bought 2 pairs . They feel great. Thanks again.

I needed this, excellent explanation! Thank you, sir!

I've been looking for some good rubber grips for my 04 R1150rt...then this video appeared. Just bought two pairs, thank you for the link!

@paidoluca

3 жыл бұрын

Same here. I wonder about the best way to cut the rubber to install the bar weight either.

@mikek1187

3 жыл бұрын

@@paidoluca I'm going to measure my bar with calipers, then make the appropriate cut there. Of course, I'm going to leave a little excess so the rubber can "squish" into place. I'd rather have a bit too much than not enough rubber.

Thanks for another great do-it-yourself video! I will try the WD-40 next time I change grips. I usually just use a hand sanitizer for grip install & also works well.

great video! helped me doing it on my K1200GT 2006 and saving couple of 100EURs!!! THANKS A LOT!!!

Great Video, wonderful and it really helps us manage our bikes. Thanks.

Love your videos!

Good DIY videothat helped me a lot, thanks 👍

thanks for your video ! i will try again ~

I installed Grip Puppies the year after I bought my 07. They are getting a little ratty, but I expect the OEM grips underneath to be like new. Probably will just get another set of Puppies if I keep the bike too many more years as the extra diameter helps me with comfort. The mai downside is some loss of grip heater effectiveness. Always a trade-off…

Generally I use compressed air to install grips with no lube or glue.

@gotahaveaGSD

Ай бұрын

I was worried about using air pressure to put them on because of the heated grips with wires.

awesome thank you

SUPER. AWESOME. REALY. TNKS.BLESSED BE. SIR

You can also use Brakecleaner as lubricate.

Would you happen to know if the tubular grip section of cast handlebars for Oilheads (like my R850R or an R1100RT) are the same size as these?

Great video. I replaced my grips on my R1150R and I can’t seem to tighten the throttle cap appropriately without the throttle sticking. What did I do wrong?

No end caps? My RT has these end caps or maybe they are call sliders. (I don’t know what they are called for sure). Didn’t see that (my bike) style on the link. Guess I’ll keep looking! Thanks Kirk for the tip! I was wondering how I was going to change them out.

@kirksmotorrad

3 жыл бұрын

They make open end grips as well

MUITO AGRADECIDO POR SUAS INFORMAÇÕES ! EXCELENTE E COMPETENTE PROFISSIONAL !!! POSSUO UMA K LT 1200 ANO 2006 COM 81.000 KMS. ROBERTO DO RIO DE JANEIRO, BRASIL. ( EXPEDIÇIONES DE MOTOS POR LATINO AMÉRICA )

Thanks, just got a 2006 k1200lt, and the grips are original, they are kind of gummy feeling, time for replacement

@kirksmotorrad

11 ай бұрын

Be very careful removing them. They are not the same as the early models and can be easily damaged.

Didn’t see this coming. Just picked up this 2002 LT, throttle is way different then in your video and what was on my ‘02 RT. Is this an OEM replacement?

@kevinmckenna5389

2 жыл бұрын

Is it not possible to add pictures? Well no Kapton tape on heated grip. Wire is in the grove of a plastic piece

Kirk any recommendations for grips on k1200rs with a throttlemeister bar ends. Thanks

@kirksmotorrad

3 жыл бұрын

They make open end grips as well

Isopropyl Alcohol works well. Id be concerned about the WD40 doing the same to the heated element wrap.

HI Great video, I have a 2010 K1300gt, will these or others work for it?

@kirksmotorrad

Жыл бұрын

I dont know... I doubt it

@carstennn1300

Жыл бұрын

@@kirksmotorrad Why you doubt it, Kirk ? I have a k1200GT, and i'll go throuh the same process ;-)(

Is there a quick fix if the gas-throttle doesn't want to snap back when you release it?

@oscartew4225

3 жыл бұрын

I have an 2004 RT with 121,000 miles. I noticed this last year that the throttle got very stiff. Almost dangerously so. It was in cold weather and I had the heated grip switch on. These are the original grips and have begun to split. I am guessing that the heated element has somehow buggered up the contact surface between the heater and the surface underneath. So unless I can fix the prob, I will not use the heated grips anymore. And may pull the fuse for it if it doesn't affect anything else.

Hi Do you interested in continue our sponsorship? We got more stuff looking for sponsoring this time!

Will that grip work on a 2007 K1200LT?

@kirksmotorrad

3 жыл бұрын

yes. Just get two sets

Ok. I tried this exactly as outlined. The old grips were virtually vulcanized to the bike. The heating element got broken. It is about the thickness of a thread. What is my way out of this?

For clarification; why should I buy two sets of grips?

@kirksmotorrad

Жыл бұрын

They are two different sizes in the package and you need the larger size

@dayneeastman1316

Жыл бұрын

@illinoisBMWriders I see, thanks for this tutorial it has been very helpful

Don't do it this way! Remove the whole switch gear unit first, 4 x 10torx screws, and 1 or 2 screws hold the grip onto the bar. unplug the electrical adaptors, and the grip assembly will separate. It will be easy easier to remove the old grip by cutting the ends carefully, and the centre section is not glued. Use a hot air gun to warm the grip up and it'll go straight on. Do not use wd40!

@kevinmckenna5389

4 ай бұрын

Why not WD40?

@kevinmckenna5389

4 ай бұрын

Can anyone answer why not to use WD40??