Very good video, thank you ! I love the "Caution!" haha. Un saludo

hey i got a new caliper setup for my 50cc, and they sent it to me with the pads out of the calipers. they didnt give instructions either, and i cant figure for the life of me how the pads are suppossed to fit in. i slide the pad in and they dont clip or anything its just getting sprung back out. i think i might have bent one of the clips to much too. are you supposed to get those little nubs of metal on the pads behind the lip of the clip or in front of them

Good video thanks. Is it normal for there to be some play side to side with the front wheel after the caliper has been mounted? Cheers.

What are the name of the slide plate or whatever it’s called that the break pads clip onto

Do you need the copper grease or can I just do it without?

Why my brake piston won't push in? plz help

How do you get the piston back out from the hole when it's been pressed to the bottom I mean atleast for me when i press it down theres no room under it for the fluid to push it back up??

Very helpful

thanks!

What’s the size for the g clamp please

Hey mate, I need new brake pads. My 125 scooter has done almost 33,000kms. Do I have to change the brake fluid too?

@terenceneedham9064

2 жыл бұрын

Dont think so. Goodluck

Were you buy that caliper

Hi how can i adjust my rear caliper iv changed the pad bit they are rubbing on the disc

@mcgeebeat

6 жыл бұрын

Your caliper may be sticking. Might be time for caliper and hose.

@peterwells6920

6 жыл бұрын

Steve McGee would a good clean sort it out?

I don't have the tool I I push back the piston

When compressing the calliper, put a cloth around the brake lever reservoirs, otherwise you will push the brake fluid back up and overflow! Or simply bleed some out with proper gear so as to not get air in the system

Whats the reason for not operating the lever with the caliper removed

@phrvlog

Жыл бұрын

Because the pistons will lock up

after changing my break pads my break is overheating very hard and the wheel rotates quiet hard too.

@rjs198585

8 жыл бұрын

+AngryGamerOnPC The brakes are binding you need to check the slider pins on the caliper are free and the pads are inserted correctly

@Gabcsu1

8 жыл бұрын

pads are good , slider pins cleaned and lubricated,i changed the braeke fluid and cleaned the whole braeke system piece to piece now it is better but still not the best maybe it needs just a few km to be good.

@rjs198585

8 жыл бұрын

The pads will need to wear in about 100 miles/ 150 km should do it :)

@ABHI72033

Жыл бұрын

@@rjs198585 after how many kilometers brake pads have to be changed?

@radiocontrolled9181

2 ай бұрын

​@@ABHI72033Depends on brake pad material and your riding style.

W

Video chance breaks brake

The hand is blockning the view

HELP!!!!!! what if I pushed on the brake handel by accident and now the piston won't go back down? How do I let the air out or something to let it sink back down and to where it should so I can put the brake pads in?????? Help!!!

@like-icecream

10 жыл бұрын

You probably sorted this out by now but just for the record undo bleed valve or master cylinder and then push it back.

Cant see for your hands

the only problem with this video is your hand is in the way about 60 percent of the time so i cant see what your doing.

New parts are too expensive. I just by a new scooter every once in a while.

@4TheRecord

6 жыл бұрын

Break pads cost like £12, a new scooter costs a lot more.