Link to buy this bushing tool on amazon is in the description👆🏻👆🏻👆🏻

@joelwomack81

6 жыл бұрын

The Snap-On Tool Review is that a crack in the frame?

@marcchantal5016

6 жыл бұрын

👍

@supersabrosinho

3 жыл бұрын

Link doesn't work anymore. Anywhere else?

@RacerXV23

2 жыл бұрын

@@supersabrosinho yes, Napa Autoparts now carries this tool as part# SER-68100. Hope this helps!

@supersabrosinho

2 жыл бұрын

@@RacerXV23 thank you 👍

I like how you edited lower volume on the impact gun, nothing worse than having to adjust volume while watching. Nice extra touch.

@TheSnapOnToolReview

6 жыл бұрын

Thanks man. Yeah I figured so too.

@TheSoravalor

2 жыл бұрын

@Andrew Brickhill yeah lmao plenty of noise fixing a car

@lawrencedavidson6195

2 жыл бұрын

@Andrew Brickhill If you have headphones on it can hurt your ears. If other people are around and you don't want to disturb them, the lower sound helps, not everyone is into what you are into.

Wow. I work on nothing but Honda’s and Acura’s and other Asian imports only and haven’t seen this tool yet or had any tool rep even mention it. This is a life saver on wasting time going to press to press them out and back in! Ordering me one NOW

This is awesome. Most videos just show how to replace this bushing by removing the entire control arm. This is way easier!

Shows you actually use the tools you review instead of some you tubers just buying fancy tools and never using them. Nice work!

@TheSnapOnToolReview

6 жыл бұрын

I use all my tools. Thanks man.

The first Eric video I ever watched was him vs. oddy door slider wheels ever since then I only trust Eric's videos such perfect attention to detail and camera placement all by himself bravo Eric bravo

Wow. That's a nice work. With out taking whole lower arm out u change the bushing. Bravo

Excellent tutorial, Joel!

Nice. Good to see the BP version in action. In an inverse of your exp, I’ve had to toss perfectly good poly bushings & use inferior ones that came with repl parts / kits b/c I didn’t have the right tool.

As always awesome video bro, I have personally learned quite a bit from you!! Thank you for turning me into a snapon fan!!!! I also want to thank you for giving me plenty of stuff to watch while the wife is on Pinterest 😂😂🤘🤘🤘

Good to see a how to video..keep them coming!!

BEST VID YOU've MADE!

Nice and easy ... Bad ass snap on gloves you have there..!!!

Omg this was an awesome video bring us more of these how to videos.🤗🤗👍🏻👍🏻👍🏻👍🏻

Great video Joel!

Great video and with the tool you were using it was pretty damn fast thanks for sharing.

Nice, and straight forward. Thank you

Awesome time saving tip and tool thanks

One of the best tools out there especially if your working on a lot of Honda/Acura’s. Not bad of the price either, with the time you save it’s worth the price.

Very good video one of the better ones I have seen very well done

Might use this method for my Honda S2000. Thanks for sharing!!!

Good job guy. Thanks for sharing

Thanks for the videos. There awesome

Love your work 🙏

Your "how to" videos are awesome! Thank you.

@TheSnapOnToolReview

6 жыл бұрын

Thanks man.

Solid Repair

Best vídeo to repair bushings

Excellent upload thank you

Nice job. Thanks

Awesome vidoe brother appreciate it!

The 3 inches of blood outro made me smile

Man you automotive guys got it easy!

shouldn't the forward bushing be tightened when the suspension is at ride height? thanks.

Great tool, saves time

Worked great thank you, 07 accord dident have to remove axle nuts.

Perfection

excellent video

nicely done! I must get one of those kits now! You made that look easy

@TheSnapOnToolReview

6 жыл бұрын

The accord and TSX are even easier!

@MA-vm6jl

3 жыл бұрын

@@TheSnapOnToolReview do u have a video link to the accord one?

Nice tool homie fast jobe

Does this same method apply for the 2009-2016 with the vertical bushing in the aluminum holder? I am having a time breaking the ball joint loose.

I’m trying to find this tool cannot find anymore, there anybody knows where I can buy this tool thanks guys

Where did you get that bushing from? I only see ones with slits inside them.

I would love to have a tool like that

Which manufacturer product would you recommend for the lower contro arm bushings for my 2008 TL-S?

Thank you

Nice Video. Do you know if this on vehicke method works for 08 Toyota Solara?

YES, Joel got to use his new pry bar.

I like how it said 'no impact' on the nut!😂😂 fair play Joel! Haven't got time 4 that shit! Great video as always m8!👍

@kwmiked

6 жыл бұрын

Rob Devitt he didn't impact on the Nut

@TheSnapOnToolReview

6 жыл бұрын

Very true. Haha

@TheSnapOnToolReview

6 жыл бұрын

I’ve warrantied the Long bolt a few times. The threads thin out but it has a lifetime warranty on it so I don’t care.

great job..

Eric you honda lovin know it all!! you sold out!!! I ❣️ IT keep up the great work Bud love the new shop also btw...quick ? My inner tires are wearing quick the alignment is perfect...compliance bushings not so much do u think I should start there?New oem struts also...

tnx

Could have used that when I replaced most of the front end on my daughter's car. Does that fit Nissan or slightly different?

Great video when you do the bolts right up on the control arm you should do it up with bit of lowed on it or at ride height. It stop the bash's from tearing. Just a idea. Thanks.

Nice video

Do more of these!!!!!!

Thanks

Hi !! Are any replacement bushings good? Thanks!

Maybe you can help me with tthe name of the sockets im looking for they have like an extension and the wobble end with the six point on the end of them i seen them in on of your videos and cannot figure out what they are called thank you

What is the minimum torque to put out and in? Can we use manual tools with long bar as extention?

"No Impact" ... BRRRRRRRRT! BRRRRRRRRRT! lol

Are these the new impact gloves Joel or the original ones ? And does that bluepoint kit only do honda or other brands ?

Quick question. Can you replace bushings on all control arms? My Crosstrek needs bushings replaced it looks like it be a lot cheaper to just replace bushings than control arms

Where to buy that special tools

Is this the same application for 2004 odyssey? Thanks

Do you have to jack the wheel up to level before tightening everything

I dunno about this mate. If you remove the lower ball joint nut, you can have it on a bench. You removed the axle nut instead, same amount of nuts but more awkward. Also, it's easier replacing the lower control arm because the ball joints are riveted in. So if your bushing is gone here, your lower ball joint bushing isn't far behind. Also, if you buy the whole arm, you don't have to press anything out at all. Way easier and better value for money

@schifoso

23 күн бұрын

It's much more for the whole control arm than just the bushing.

Do we have to torque it back on to a specific amount?

Thumbs up. Good video. However, I wish you'd address the inquiries as to why you didn't torque down the control arm fasteners under load as several sharp viewers are pointing out. I'm curious about that as well.

01 odyssey. At highway speed the van veers right when foot taken off accelerator. The steering wheel a actually ticks slightly left when this happens. Then the van corrects itself when accelerator is pressed again. And goes back to straight. There is tiny tie-rod play both sides. Tires have even wear. Van cluncks front left when accelerating after coming to a complete stop. Front and upper right motor mounts were just replaced. My nephew replaced both struts and springs about a month ago. Passrnger side vertical control arm bushing has some cracking. Van has 191,000 miles. All rubber suspension bushings were replaced at 135,000. Plus motor and tranny mounts.

More videos like this!

I have a question I can see that the bushing u replaced in the video is the same i see in my honda civic but it looks damaged. When i drive above 60 mph my steering wheel starts to shake u think thats the reason why its doing that.

Did you get the bushings from honda let me know thanks

Sweet

Thanks for the video. Curious why this bushing seems to fail over time, but the other horizontal bushing doesn't have the same issues. At what point do you feel you should replace the entire arm with new bushings and ball joint vs. just replacing this bushing.

@May16Joe

Жыл бұрын

It depends on the people. Some people prefer original honda parts but a lower control arm is around $400 but the bushings are around $60 each so they rather replace the bushings only. Some people don't care about original honda parts and buy a new aftermarket lower control arm for $70.

Wow you make this look so easy!! Why do mechanics say it’s more labor to replace the bushing then replacing the control arm?

Does this bushing tool work for the 08 accord?

Can this be done a TL

Would the same procedure be for 99-04 odysseys?

I think that the direction ball joint is not fixed right because the curvature of the ball joint axle goes always to the inside to avoid the wheel , correct if I am wrong

Cool video but did anyone else notice that big chunk of metal that came off @ 7:58 ? Will that be a big deal? I’ve been thinking about replacing my own bushings so I’m watching these videos.

Would you need an alignment after replacing just that bushing

BAM !!!

does replacing control arm bushings help steering feel better?

I'm about to do this for my Toyota Corolla, and watched your great video makes me nervous! hope all goes ok, will not be doing in the Toyota dealership, but CB, is very expensive as well!..

Cool beans

Nice. Dealer wants 2 grand to replace on my odyssey. I think I’m gonna do myself

oh the csx, one of the cars we didnt get in the us. I would love a civic si with leather but not in the usa

Can this method be used for a 8th gen civic? (2006-2012)

Awsome video, my dealer told me yesterday that snap-on has a new brushless 18v 1/2'' impact out now , maybe you could ask Tyler and see if it is true thx keep rockin.

@TheSnapOnToolReview

6 жыл бұрын

Oh I know its true. I've seen the specs and picture. but I wasn't supposed to say anything. but if your dealer has told you then yeah, It's coming!

I was thinking about getting one of these. Do they fit the SantaFe / Accent etc. control arm bushings as well?

@TheSnapOnToolReview

6 жыл бұрын

I honestly think they are just a bit off in size.

Awesome video! Can I use this tool for 09 honda accord?

@zigner

4 жыл бұрын

No, the bushings are different size after 07

How come u didn't tighten the control arm bolts on a load?

@negrumarius

4 жыл бұрын

👍

I know it’s an old video but can you update the link on the bushing tool? It’s no longer available

Nice compact impact gun you're using for this video. Who's the maker?

Nice video. Should you not preload the suspension before tightening the bolts?

@TheSnapOnToolReview

6 жыл бұрын

Thanks man. Just the horizontal bolt but honestly I’ve never seen a torn horizontal busing in 20 years of doing this.

Where are you located ? California by chance?

Can I do this on a 2000 intrepid???

How long did this job take approx? What is the cost for this job?

How did you live before having those snap on pry bars

What kind of noise does a broken control arm bushing make?