How to Replace Ignition Switch 07-16 Chevy Silverado
Автокөліктер мен көлік құралдары
Buy Now!
New Ignition Switch from 1AAuto.com 1aau.to/ia/1AZIS00204
In this video, 1A Auto shows how to remove and replace a broken, or malfunctioning ignition switch. The video is applicable to the 07, 08, 09, 10, 11, 12, 13, 14, 15, 16, Chevy Silverado.
This process should be similar on the following vehicles:
2007 Chevrolet Silverado 1500
2008 Chevrolet Silverado 1500
2009 Chevrolet Silverado 1500
2010 Chevrolet Silverado 1500
2011 Chevrolet Silverado 1500
2012 Chevrolet Silverado 1500
2013 Chevrolet Silverado 1500
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oU8/1AXAA00013
• Phillips Head Screwdriver 1aau.to/oU8/1AXAA00013
• 10mm Socket 1aau.to/oNj/1AXAA00017
• Ratchet 1aau.to/oZj/1AXAA00016
• Pick 1aau.to/okT/1AXAA00037
Subscribe: / @1aauto
Check out our playlist:
Chevy Silverado 2007-2013 2nd Gen: • Chevy Silverado 2007-2...
For More Info visit us at 1aau.to/h/afW/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Пікірлер: 105
√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
@leroyzimmer7834
2 жыл бұрын
How to replace 6346A in a 2007 Yukon
@leroyzimmer7834
2 жыл бұрын
How to replace 6346A in a 2007 Yukon
@kevinAuman1
Жыл бұрын
Okay so I have an 08 yukon denali and unfortunately when I turn the key I get absolutely nothing not even a click, I have replaced the starter, new battery and cleaned the MAF previously it would start then shut right back off then eventually it wouldn't do anything at all also the scan tool/code reader is unable to connect to the trucks computer would this ignition switch be the cause of my issue? I did try to jump the starter solenoid and it spins over the engine just does not start...
This video saved me seriously! I was going straight off the Chilton's manual, and the manual missed the step you showed of rotating the key back to the stop position before removing the ignition switch. Thanks a million!
you guys are one of the most consistent and helpful KZread channels in the last 10 years
Successful install. I have a 2012 GMC Sierra. Word of advice. You don’t need to have the back key accessory mode. What you need to ensure is that the gears on the old switch match the gears on the new. Hand turn if need be on the new switch before installing to ensure an exact copy. From there you can install the new switch without having to manual turn the gear with a screwdriver or worry about putting the cylinder lock back in. My truck works just fine after install. Note! To avoid dealing with the reprogramming of the theft device don’t disconnect the anti-theft mechanism. Simply slip it off and let it hang plugged in. It will save you some trouble!
Thanks for a great video guys!! Saved me some big bucks taking it to the dealership. My truck was cutting out driving and very soft starting. Works like a champ now.
@1AAuto
2 ай бұрын
+@Cxnnxr1 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
Thanks for this video. Really helped me out replacing my ignition switch in my 2009 Silverado
This is fine if you have a vehicle that will go into accessory mode, but what if it doesn't? How do you line up the ignition switch with the lock cylinder?
Excellent Work.... Top Notch Teaching Style.....
I bought my 97 chevy ign switch from 1A that wasn't my issue, my wife hastled me to get a return label. They didn't make me return the item. So I didn't have to dig it back out after testing the new part THANK YOU 1A!!!
@1AAuto
3 жыл бұрын
+Robert Kissler Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
This video is really great and you guys save my life thank you so much
@1AAuto
4 жыл бұрын
+Semik Aghakhani Thanks for checking us out!
Good video, but my truck like some others does not turn back for accessory. I looked through the comments and found some very helpful information.
Thank you for this video. The only issue I had was removing the lower valence panel - but now that I know how hard I need to pull on it, removing it would be easy the next time. It took me longer to gather the tools and remove the stupid valence than to actually swap the switch. PRO DIY TIP: use a pair of needle nose pliers (long, angled works well) to depress the two spring-loaded clips on the switch at the same time. I couldn't get it with two picks, but the pliers worked great!
Just wanted to say thanks the video was very helpful and made it where I could do it myself
@1AAuto
4 жыл бұрын
+Travis Horne Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com
This video helped a lot worked for me 👍🏻
Thank you so much for the video it helped me do the job thanks again Bob.
How do you know if the lock mechanism or the switch is the part at fault? My key gets stuck in the off position. Very hard to get it to move to start.
@chadportenga7858
2 жыл бұрын
That sounds like the cylinder is bad. When I took out my switch, the lock cylinder rotated very freely (when I put it back in). You can rotate the teeth on the switch with your fingers - takes a little force, but not very much.
I got the job done thank you.👍🙏>>>💚
Great video
Is there a way to disable the steering wheel lock in a 2016 gmc sierra to be able to flat tow it behind my rv without having to disconnect battery? Also, I would like to be able to remove the key and lock the doors..
I have a 2011 duramax base model lt I guess would I have to program the switch after replacement?
How do you replace or fix it if the key doesn't want to turn or don't have a key?
How come my lock cylinder won't lock in? I followed the instructions, but I don't know why it slides out with the key?
Thank you 🇺🇸
Thank you!
John 3:16 For God so loved the world that he gave his only begotten Son that whosoever believeth in Him shall not perish but have everlasting life.
Should I test it before totally reassembling it?
Im in spirit lake idaho by any chance do you guys have a recommended mechanic trustworthy in this area?
If the key is just sticking, is that a cylinder issue or does the whole ignition system need to be replaced?
Video is great but you want 20 bucks more than amazon for the same part. That's a problem. Yours 35, theirs 15 same Dorman part.
Very helpfull wats the cost on switch
If someone jammed a screwdriver in my ignition switch, and my key doesn't turn to the start position, how do you recommend proceeding past this sequence?
Is this the same process for a 08 Chevy Impala?
My ignition cylinder will rotate to the start position…but will not start the truck…then when I released it..the starter engages and starts the truck…? ..It did this for several days…. Now when I turn the key nothing happens…? The battery has been tested and is good. Do you think it is the ignition switch..….or the starter. My truck is a 08 GMC
If I change lock cylinder from another vehicle do I need the theft device also for the key to work or just the lock cylinder will work?
@tylerrobinson6432
2 жыл бұрын
yes you do
How is it going guys Just a quick question do I have to program the new ignition switch on my 07 silverado?
@1AAuto
3 жыл бұрын
+mr freeze Thanks for checking us out! The part will not need to be programmed once installed. Please let us know if you have any further questions, thank you!
I have the dtc b1441! This video is the solution!??
I'm having issues with the fobs not working anymore and someone mentioned ignition issues. Would that just be the switch not knowing if the keys in?
@mrmotofy
Жыл бұрын
Battery in the fob first
I have a 2017 Silverado 1500, my keys turns all the way but it makes a clock sound after trying to turn it on, I replaced my ignition starter switch and got it re programmed but I’m still having the same problem
How do you align the gears on the switch? Right now I only seem to have 3 positions and truck starts but only runs for like 2 seconds
@JasonTheMunicipalMechanic
3 жыл бұрын
I had the same problem where my ignition would not go into acc so I removed the lock cylinder and used a screwdriver to rotate the section in the column that turns the switch counter clockwise, it will stop in the correct acc position then I put the switch in and used the screwdriver to turn the same thing in the column clock wise to the run position just before the start position and inserted the lock cylinder back in. It sounds harder than it is.
You don't need to pull the lower dash panel.
Is there any programming need for the key or anything
Hello i followed your instruction but unpluging the key security thing does that have to be reprogram? My truck is not starting now. Its like sticking in a key with no chip. Power starter fuse are good.
@tkn24s
4 жыл бұрын
Stan B did you end up reprogramming it?
@stanb8419
4 жыл бұрын
No i did just as your post did. No reprograming.
@stanb8419
4 жыл бұрын
Cause a friend told me after, I shouldnt have unplug the security.
@tkn24s
4 жыл бұрын
Stan B ok tnx mine is getting stuck alot of times and it’s frustrating, im going to try it
@Schnauzer.kennels
3 жыл бұрын
What did you end up doing to get it to start?
At 5:09 I could not rotate the key back until I pushed in the white tab back from 4:04.
What would be the reason to change this? My 2011 Silverado is getting no power when the key is in the ignition, no lights. Would that be why?
@killer2000911
3 жыл бұрын
I’m having the same problem. Did you get it fixed? And how?
You guys outta sell on Amazon I'd buy from you more it's just easier
If you have a diesel, how do you remove panel without damaging the trailer brake lever panel?
@streetrattv2304
Жыл бұрын
Do you have a duramax?
Most Chevy truck do not have the acc position he mentioned.
dorman has a new kit for tumblers that lets you keep the same key for doors/ignition!!!!!!!
I have a 2016 gmc and my key does not turn backwards to accessorie mode
If you run into no start check your ecm ign fuse
Does this work on a 2015 Chevy Suburban?
@1AAuto
3 жыл бұрын
+Bellal K We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
I'm having an issue turning my ignition on I darn near go back and forth with the key a million times would this fix it
In the beginning after you said to put the key in the ignition and put it in start position. What if after putting the key in, but to put it in start position, it doesn't recognize anything. After trying to get the key out because it was stuck and wiggling it got the key out of the ignition. Now the switch doesn't work at all. So it can't be put in any position for power, start nothing.
Quick question have new switch in but cylinder won’t go back in??
@bretdibacco5409
3 жыл бұрын
Problem solved you may have to manually move the gear to auxiliary position. Other than that 1a is awesome I called and had a tec call me
Followed exact directions/ instructions but lock cylinder will not go back in so I can remove the ignition switch, as of right now, I’m stuck! Can anyone assist? Lock cylinder goes in half way and stops in wiggled etc but won’t go past that Point. I did not remove key or anything, followed directions step by step.
@Gsxr5slow
3 жыл бұрын
I'm having the same problem. Did you ever figure it out??
@JasonTheMunicipalMechanic
3 жыл бұрын
I had the same problem where my ignition would not go into acc so I removed the lock cylinder and used a screwdriver to rotate the section in the column that turns the switch counter clockwise, it will stop in the correct acc position then I put the switch in and used the screwdriver to turn the same thing in the column clock wise to the run position just before the start position and inserted the lock cylinder back in. It sounds harder than it is. I plugged the switch in last
how about if the key i lost and the key does not match the doors so no coding
What happeneds if this part is not working properly I have 2011 turns the key but won’t star battery is good and I replaced the key cylinder
@1AAuto
10 ай бұрын
+Marco Nava We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I am doing this is a 2009 sierra, but I have no ACC mode for the key, any ideas before I progress?
@brandontaylor7483
4 жыл бұрын
LibertarianUSMarine did u ever figure this out I’m having same problem
@91prostreetstang
4 жыл бұрын
The very first click on ignition switch is accessorie at least on the 05 mu wife drives and my customers car I am working on now.. :::put key in turn to 1st point and that's accessory.. I am working in a 2007 chevy 1500 now I didn't mention that part sorry
@JasonTheMunicipalMechanic
3 жыл бұрын
I had the same problem where my ignition would not go into acc so I removed the lock cylinder and used a screwdriver to rotate the section in the column that turns the switch counter clockwise, it will stop in the correct acc position then I put the switch in and used the screwdriver to turn the same thing in the column clock wise to the run position just before the start position and inserted the lock cylinder back in. It sounds harder than it is.
P2534 code what ignition switch is it talking about this or the one with the key,please help?
@josephdavis38
3 жыл бұрын
The P2534 code is signaling a faulty ignition switch. The part with the key is called an ignition lock.
I have an 07 Ext Escalade and when you turn the truck off that's it... the key will not turn back any more.. I don't believe it has an accessory
My key does not open the Switch, how can I solve it?
@1AAuto
2 жыл бұрын
+Rigo Soto We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I followed a different video and it DID NOT have me putting the lock cylinder back in before removing the ignition switch. BIG MISTAKE. Since it was in the start position when removed, it must be in the start position when reinstalled. The problem with that is to put it in START, the switch gear has be be all the way to the end. It is also spring loaded, so once you remove the switch, it moves from the start position to the on position. You can not put it back to the start position when reinstalling the switch. There for the lock and the switch DO NOT line up. Can anyone tell me how to fix this problem. When I put it back together, it will not go all the way to START. Therefor, the engine does not start. H E L P !
What was the problem
Ignition cylinder won’t go in all the way
I installed it but the key won't come out
Be careful with this. You may not need to remove the key solenoid to reset. Be careful I had a hard time reinstalling. And I almost damaged it. Do not remove key at anytime until the whole full setup is complete then reconnect the battery.
@chadportenga7858
2 жыл бұрын
Not sure what you're referring to, but my key came out of my cylinder after I removed it. I just put it back in and it was fine. The cylinder will only go back into the hole one way. It goes in very freely - if you have to force it, try turning it 180* and see if it goes in. Remember, it needs to go back in roughly in the "start" position.
I got a 2012 and you gotta wiggle the key until it unlocks to turn over . So annoying!
@1AAuto
4 жыл бұрын
+dave roberts Thanks for the feedback!
@1AAuto
4 жыл бұрын
+dave roberts Thanks for the tip!
I changed mine and now my truck won’t start
@1AAuto
3 жыл бұрын
+Brandon Schrader We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@Schnauzer.kennels
3 жыл бұрын
What did you end up doing to get it to start?
@jaydiaz3567
2 жыл бұрын
Any resolution?
@patriciareynolds2729
2 жыл бұрын
Ed here me too, now lock wont come out., couldnt read the tumbler nos. on old one and caused problem
If your vehicle accessory is in a forward position as opposed to all the way back - watch this video from the same crew instead kzread.info/dash/bejne/iol7ksSdnNzQctY.html