To put the locking ring back on is pure hell

@tpowell2072

Ай бұрын

Yup I’m currently stuck on it . I ran out of day light and gave up only had a hour lol

Awesome video! It is very detailed, and helpful - thank you! I was able to remove the old fuel pump, and install a new one because of this video. :)

@jims162

3 жыл бұрын

How did you make sure all the tabs locked in the back part of the locking ring? Can't seem to get them to all to engage at the same time.

@michelleharris24

3 жыл бұрын

@@jims162 A lot of patience! Lol First, I positioned the pump at a slight angle to allow all of the tabs to be above the top of the pump. Prior to doing this, I had not positioned the pump correctly in the tank. Thus, the pump was below some tabs in the front, and was above some tabs in the back, which did not allow the locking ring to fit under all of the tabs at once. Second, I held (and pushed down) a small stone on top of the pump to stop the pump from moving / popping up. Next, I positioned the locking ring on top of the pump, and made sure it was aligned with each tab. Lastly, I focused on one tab and used a flathead screw driver to slide the ring under the tab. I slid the ring about 1/4 of the way under the tab, checked the remaining tabs to make sure the ring was under them, then used the screw driver again to hit the ring clockwise until it locked in place. It definitely took some time, and there was a learning curve since this was my first time doing the install. But the install isn't too bad once you've learned about the nuances involved. I hope my explanation made sense. Also, I apologize for the late response! I didn't see the email notification about your question until now. I hope you are having a great week! :)

the most replayed spot is at 3:22 because everyone (as well as I in this exact moment who had to go to youtube to see how someone did it) could not get that giant sucker into that little tight awkward wet hole followed by the float all while holding that fuel line. you must get the float in first at angle then put the rest in ,, thank you great video. cleared that right up. oh yeah its spring loaded, so you have to push it down to get that giant lock nut back on. (which feels like you might break it, but you wont)

Thank you for this video. I was judt told by someone who listened to the pump through the open fuel cap that it was bad, so thus will be my first replacement in trying to get the car repaired. The car isn't in terrible condition but so many parts on it need to be replaced that it's not able to run.

Very helpful and very descriptive thank you

Good video! I was shown to use a hammer and a brass drift to take the retaining ring off. Using the screwdriver and a hammer it could actually spark and cause an explosion. Use extreme caution ⚠️

Thank you for the straight forward "how to". Confused myself for the moment when I thought I needed two pumps, one for each side, and only purchased one pump.

@kurtwalton1201

Жыл бұрын

You only need to buy the pump for the right side correct? What’s on the left side?

@AbandonTheWest

Жыл бұрын

@@kurtwalton1201 I only have one pump, on the left side.

@kurtwalton1201

Жыл бұрын

@@AbandonTheWest okay yea I replaced my pump on Sunday. Everything went smooth except the locking ring was a PITA to get back on🙄

Putting back the locking ring is a pain. The new gasket was too thick so I had to reuse the old gasket and had someone help push the locking ring down while I tapped it back in place.

Hey that was a great video enjoyed it if I have a problem with my fuel pump I'll know how to fix it thank you👍🐎

Putting the locking ring back on is quite tricky, the opposite side of whichever side you tap with screwdriver can pop up and over the notch it needs to go into. Check that every notch is locked. I popped mine on (easily or so I thought) but 2 notches in the back didn't lock- when I went to gas up gasoline poured out all over the place. 2009 Mustang Bullitt #5858. Very helpful video.

Hello, I'm replacing the jet pump which direction should the arrow point to? The front of the vehicle? Thanks for the video!

tank you it look very simple

@amandacasey68

Ай бұрын

No pun intended 😂

Thank you

Interestingly enough you can’t create a spark from hitting the plastic handle of a screwdriver with any kind of hammer but great video man very informative and good views of what you’re doing 👌👌👍

@MentalMan38

3 жыл бұрын

Which is why he was referring to the sparking coming from the metal on metal contact of the flathead screwdriver on the locking bracket. If you hit too hard on that locking bracket and the screwdriver skips the surface of that metal, it could very well create a spark.

@raulmartinez3484

Жыл бұрын

The rubber hammer is meant to minimize it from occurring. To be completely safe, it’s best to use a brass punch to do this because the brass punch won’t create any sparks.

what is the hose that connects to the thing with the green clip? we broke ours and need to replace it. the new green clip doesn't fit on the hose and we want to get the entire thing

Does this one come with the fuel pump inside already or do I need to transfer anything over or this one is just the float only in spot A

I’m getting code P2198 & the car cranks but doesn’t start . Think i need to do the same procedure?

I'm having an issue with the fuel gauge sticking. But no code. Is it the sending unit. 2014 mustang gt

Would this issue cause an udle surge in the vehicle?

I need help figuring out why the fuel pump that has been replaced with the new one is not working I have a 2008 Ford Mustang can you please let me know what could be the problem because two mechanics have tried and it only works for about 2 weeks and

I have 2007 mustang v6 4.0 replaced the driver side and wanted to do the passenger side pump are they the same part I need to know before busting up knuckles trying to get that pump retention ring off 😂😂🤬🤬🤬please help

Steel on steel will create a spark. Use a piece of brass in the steel ring to avoid creating a spark... a dead blow mallet is good too. Do not use steel on steel anywhere

That locking ring was the tricky part of this job. I had to re-use the old O-ring as the new one was too hard to compress. Then, I filed the leading edge of each of the engagement points so it would catch properly. POS...thanks FORD.

@ps4gaming233

Жыл бұрын

Same thing happen to me I put the new O-ring and it made it tricky because it wouldn’t go on the area under the metal part of the part of the seat but when I put the old O-ring it worked just fine thanks a lot!!

I'm struggling to put the locking ring back on

@tpowell2072

Ай бұрын

Same doin it now did you ever figure it out I need help lol

@amroelmughrabi

Ай бұрын

@tpowell2072 I drove it without the locking ring to a garage, gave them 6 dollars and they locked it, I did it two times now, but have to be careful as fuel will be everywhere while driving.

Right side sending unit for 2012 v6 Mustang has a pump as well? When I climb, the right side makes noise. Left side driver side pump has been replaced already. Please help. Thank you.

@MartinsUsedCarsCollectiblesLLC

2 жыл бұрын

Yes. Mustangs have two tanks (also known as saddle bag tanks). The passenger right side tank has a Fuel Sender Unit. It picks up the fuel in the right side tank and sends it through a hose to the left side fuel tank. Here is a link to purchase one from Parts Geek. Double check to make sure it fits your Mustang’s year and trim. www.partsgeek.com/5dpq2cg-ford-mustang-fuel-tank-sender-assembly.html

Is the fuel pressure regulator built in the fuel pump for the 4.6 engines?

@lilcholo2097

2 жыл бұрын

Yes if you still need the info

Ngl, well shoot that looks rather straightforward. The fuel pump in my manual 05 went out (not sure which one so I'll probably just replace both) so the car wont start at all. We ruled out the battery and air intake because the battery still had a charge and the intake was still pulling in air, it just wasn't getting any fuel.

@julienson2

Жыл бұрын

How did that work out ? My 07 cranks but don’t start

@Razgriz6464

Жыл бұрын

@@julienson2 It worked at first but now I'm having the same issue of it not starting. I'm trying to narrow it down to replacing the fuel filter and seeing if that fixes the issue. And if not, it might be a fuel pressure sensor causing the issue. I'm hoping its not a sensor cuz I don't really wanna drop $90 bucks on a new one. And if neither of the above things fixes the problem, then I have no fargin clue what's making it not start.

@pootpoot1001

Жыл бұрын

@@Razgriz6464 how did you check the air intake?

Martin, great video-easy to follow and understand. One question-I have an 07 Gt, 4.6L, and I have as much gas in the tank as I can get in there and it is registering about 2/3 a tank. First, I am guessing this is the sending unit malfunctioning, correct? Secondly, how do you know which side to change? Thanks! Ken

@MartinsUsedCarsCollectiblesLLC

Жыл бұрын

Use a code reader to determine which side is malfunctioning. Yes, the sending units have a float to determine how much gas in in each tank.

@kencampbell8324

Жыл бұрын

@@MartinsUsedCarsCollectiblesLLC Thanks Martin! I will get a code reader and make the determination.

@MartinsUsedCarsCollectiblesLLC

Жыл бұрын

@@kencampbell8324 you may have to go to a mechanic for them to use a more detailed industrial code reader. Most shops have code readers that have more functions than the small “over the counter” consumer readers available.

Can someone help. I have an 05' mustang V6 I just did a fuel pump replacement on with a deatschwerks dw300. Car starts and runs fine for a little while but for some reason after driving around for a little while it decides not to have fuel pressure anymore. I've had this issue before with another V6 using the same pump but I never figured out why that car had the same issue.

@larrymora992

9 ай бұрын

The same thing happened to my 2006 v6 4.0. It runs for a good 10 miles and the stalls.

@stevenlopez5832

9 ай бұрын

@@larrymora992 figured out it was just the deatschwerks pumps. They're garbage. Switched to a walbro pump no more issues.

Hi I also have an ‘06 mustang V6 getting code P0193! & car is getting very low gas mileage and rough idle at times should I get the sensor just or the pricey fuel pump?

@MartinsUsedCarsCollectiblesLLC

3 жыл бұрын

It’s a toss up. The ultimate goal is to fix the problem. Choose the option that will accomplish that goal the first time. It will save you money in the long run.

@ezracarrizales23

3 жыл бұрын

Did u ever fix ur car?

@vladshcherbakov3112

2 жыл бұрын

I had that code, it's a fuel pressure sensor. Easy fix, just needed to buy a part and a Torx screwdriver. HELL NO! YOU DO NOT NEED THE WHOLE FREAKING FUEL PUMP! Come here for fuel pump when you can't leave the parking lot. The fuel pressure sensor is just an emissions thing mostly, my car was running even with that dead.

Does the cross over pipe ever go bad? My car performs better when I have a quarter tank full compared to half. What could be the issue in the fuel tank? 2012 v6 mustang

My car is having a p0193 code for bad fuel rail pressure sensor. Still runs good but its running at apparently 75psi according to the ob2 ready. Any help???

@briandouglas8744

3 жыл бұрын

Also it a 2009 mustang 4.0

@MartinsUsedCarsCollectiblesLLC

3 жыл бұрын

I would replace the Fuel Rail Pressure Sensor in the engine. Here is our video on how to change the FRPS. kzread.info/dash/bejne/mGFsqburmcapgLg.html

@briandouglas8744

3 жыл бұрын

@@MartinsUsedCarsCollectiblesLLC any where I can get one that's reliable and cheap cause I haven't found a cheap one

@MartinsUsedCarsCollectiblesLLC

3 жыл бұрын

@brian douglas - Walmart (online) is $13. Amazon is $22. Advance Auto parts is $66.

what exactly is the purpose of the fuel sending unit on the passenger side of the gas tank? I have already replaced the fuel pump but still having spratic fuel issues. I have a 2012 v6 mustang

@MartinsUsedCarsCollectiblesLLC

2 жыл бұрын

For Mustangs with saddle bag tanks, the passenger right side tank has a Fuel Sender Unit. It picks up the fuel in the right side tank and sends it through a hose to the left side fuel tank. Here is a link to purchase one from Parts Geek. Double check to make sure it fits your Mustang’s year and trim. www.partsgeek.com/5dpq2cg-ford-mustang-fuel-tank-sender-assembly.html

@loneranger5349

Жыл бұрын

To send the gas over from the pump side

Why replacing the entire unit if u can replace strainer?

So is the sending unit the same thing as the "fuel tank jet pump"?

@MartinsUsedCarsCollectiblesLLC

Жыл бұрын

The jet pump is on the passenger (right) side of the saddle-bag gas tanks in the mustang. The fuel pump sending unit is on the driver side.

Gracias !!!! Me voy ahorrar unos dolares

was your gas gauge going from full To empty and back to Full again ? Mine just started doing that

@CharlesBrown-jc6gb

Жыл бұрын

That's what ours is doing. is it the same problem, or in our gauge

@tracytedder5975

Жыл бұрын

That's a good question

This would be for the 2010 model too! Despite its face lift, mechanically it’s really the same as the 05-09

@MartinsUsedCarsCollectiblesLLC

2 жыл бұрын

Yes

@danielrevollo3278

Жыл бұрын

@@MartinsUsedCarsCollectiblesLLC what about the 11 to 14?

The ring. Why no one shows the process? 😥 all channels are the same.

@ivans4.098

3 жыл бұрын

Did you figure it out I still need help

@danielkohler3458

3 жыл бұрын

because it's not very video friendly. I.e. it doesn't look pro trying to get that damn thing back on correctly

@jercobienixon929

2 жыл бұрын

I’m actually having a problem getting the ring and the seal back on.

@tpowell2072

Ай бұрын

Here for the same any help plssssss

I have an 08 gt mustang. Replaced the fuel pump due to delayed fuel pickup and delayed gauge readings. No check engine light on during any of my issues before or after. Runs out of gas before i'm actually out of gas. Saddle side is full and no pickup is happening from passenger side to the pump. Checked the pickup tube from passenger to driver side and it is not clogged, I ran air through the pipe and air is going through just fine. At first, car would read 0 miles left and die at half a tank, now it's running out at 3/4 full on the gauge where i'm only going through roughly 5 ish gallons or so. It's taken apart right now but I don't know if the sending unit on the passenger side has anything to do with fuel pickup from the saddle side, meaning I don't know if when the sending unit on the passenger side is bad, it cuts off fuel pickup from the passenger side. It seems the pump has a t split on the top to pull fuel from the passenger side, and the drivers side picks up from the bottom on the driver side. Any idea what it could be? No places around me have the sending unit for the saddle side in stock so i'm trying to figure it out without buying anything. And the notch was lined up perfectly and the pickup tube was attached properly after swapping in the new pump.

@SalimRecio

3 жыл бұрын

Bro, did you solve it?

@SalimRecio

3 жыл бұрын

I have exactly the same problem

@GlorifyGodInEverything

3 жыл бұрын

@@SalimRecio I can't lie to you, the car is still sitting in the driveway, i've just been using my truck because I use it for work. From everything that i've researched about it, it should be the fuel sending unit or an issue with the wires running to the tank which the tank would have to be dropped for. Most people have said that it is the fuel sending unit itself and some ford techs have also said this is a common issue with the fuel sending unit as well so I would suggest that before you decide to go all in ripping the tank out and tracking down your wires.

@SalimRecio

3 жыл бұрын

@@GlorifyGodInEverything thanks man, I think im going to replace the fuel sending unit, if it doesnt work I dont know what else can do, may be the ecu. Hope replacing the fsu works.

@GlorifyGodInEverything

3 жыл бұрын

@@SalimRecio yea good luck man! let me know how it goes.

Does it have two fuel pump ?

@MartinsUsedCarsCollectiblesLLC

3 жыл бұрын

Yes. One on each side of the back seat.

@richardpatricio3502

2 жыл бұрын

Do we have change both of the fuel pumps ?

I followed every step thank you, but when I went to the gas station to fill up it let out all the gas. I don’t mean leaked, I mean like gushed out. Any idea what I did wrong or what it could be?

@MartinsUsedCarsCollectiblesLLC

3 жыл бұрын

The cap lock is very difficult to secure. If it came off, then the unit can pop-up and gas will come out of the unit.

@tek9stylez

3 жыл бұрын

@@MartinsUsedCarsCollectiblesLLC thanks for your reply, upon inspection I noticed that the O ring had slipped off.

what fuel pump did you use off of amazon?

@MartinsUsedCarsCollectiblesLLC

2 жыл бұрын

Here is a link to a 2005 Mustang fuel pump: amzn.to/3koIVj0 Here is a link to a 2006-2009 Mustang fuel pump: amzn.to/3OPMIDI

Everything going great until getting that locking ring back on...

@MartinsUsedCarsCollectiblesLLC

3 жыл бұрын

Yep, the locking ring is difficult to put back into place.

Where'd you get your unit from?

@MartinsUsedCarsCollectiblesLLC

3 жыл бұрын

Amazon

@RobertYayo

3 жыл бұрын

@@MartinsUsedCarsCollectiblesLLC the E2469M right

@MartinsUsedCarsCollectiblesLLC

3 жыл бұрын

@Strom Berto - Yes - Items Ordered: 1 of: Gas Fuel Pump Module Assembly for 2006 2007 2008 2009 Ford Mustang V6 4.0L V8 4.6L SP2099M E2469M

@RobertYayo

3 жыл бұрын

@@MartinsUsedCarsCollectiblesLLC just bought that one I say many videos about that one and how it fits perfectly I bought E2467M and it was taller and I couldn't run it because gas would surly leak out

After replacing pump and filter car still won’t start, gas getting to fuel bar but not starting

@BerkinParlakay

3 жыл бұрын

make sure your fuel pump module is plugged in, try pressing the fuel pump reset button near the trunk latch in the drivers footwell, try a new starter, try a new battery

@newfie-dean5803

3 жыл бұрын

Info on fuel system here: kzread.info/dash/bejne/hnV3uJmhp7Otg8Y.html

Don’t know if I’m trippin or not but I don’t think he put a Fuel filter in lol

@newfie-dean5803

3 жыл бұрын

The fuel filter is actually located underneath the car so you change that through access beneath the car.

not as easy as that must be the second time

Why the fuck would a fuel pump be spring loaded

2005 Mustang GT: I go to take off the tube, and the fuel comes spraying out, not just a bit.

@jamisondiehl5817

11 ай бұрын

Same shit happened to me. Did you find out what happened?

@Excalium

11 ай бұрын

@@jamisondiehl5817 If stopped after about 15-30 seconds. I think the pressure of the fuel in the line just sprays it out. But I’m not a car mechanic.

Ya sure I got news it's not easy to put that ring on it's nearly impossible so show how long it really took to put the ring on. Be aise 8f this . This is why people watch your vid to see if there's a easy way to install that ring it just does go in easy like you showed. Period no two ways about it

@Blazerghost

10 ай бұрын

Yeah I’m trying to do mine currently, fkn nightmare

@tpowell2072

Ай бұрын

Any luck I’m doing mine now all done but the F N ring !

Is there another unit on the other side. Does it need to be replaced

@MartinsUsedCarsCollectiblesLLC

11 ай бұрын

The mustang has two units. The one on the passenger side moves the gas to the tank on the driver side. The driver side sends to the engine.