a little too talkative for my taste, but extremely helpful!
@abbasjackson5459
2 жыл бұрын
Why would I bore you with bla bla bla when you can see it for yourself, Appreciate the coment
@randymaclean27072 ай бұрын
The circular clip comes off the shaft without all the prying if you simply grip it at the edge with waterpump (large) pliers and rotate it counter-clockwise. The tabs are slightly angled, so it will spin off like a nut. This trick saved me a ton of time and effort.
@jasont78148 ай бұрын
Dude, you’re a lifesaver. Worked like a charm. Tractor Supply tires, $14.99 each. Thank you!
@mikethetooth2 жыл бұрын
I wish all how to videos were straight to the point like this. Excellent video! Thank you
@theghostwizard67455 ай бұрын
Genius. Thank you for not talking for an hour to explain 2 steps. LOL
@CookieZ33533 жыл бұрын
I'm 63 and I did it with a small crow bar, a hammer, and WD-40. Thank you. I replaced my flat tire with a "no flat" variety. (However, I'm whooped!)
@BlueRidgeKat1
2 жыл бұрын
You go girl !!!!!!!
@folsomtransport3 жыл бұрын
Cool this is the first one that showed me how to get the cap off! Took me less than 5 minutes to do it. Thank you!
@JesseCanchola10 ай бұрын
Thank you so much! This did the trick. I WD-40'd then used the claw of the hammer to remove. Hard part was finding the replacement locking washer at either Lowe's or Home Depot. Found them on Amazon as key words: Internal Tooth Starlock Washers, Push On Locking Washers, Speed Clips, Fasteners.
@briandimascio3624
8 ай бұрын
U can reuse the push nut. I used channel locks to deform the edges instead of a hammer and then bent it back with a small adjustable wrench while holding the other side w channel locks so it is too tight to slide over the axle. Find a socket that will clear the 1/2or 5/8” axle and hammer it over. The teeth will lock
@williamgarcia96022 жыл бұрын
Thank you the wheel was put on backwards, but still helpful.
@abbasjackson5459
2 жыл бұрын
On purpose
@demlafields1806 Жыл бұрын
You tube videos have saved me 75.00 today, a guy was going to charge me to change the tire. Hod Bless U-tube
@novoselpro2 жыл бұрын
EXACTLY what I was looking for. Thank you!
@donnieg.6976 Жыл бұрын
This was perfect. I was able to change both wheels in less than 10 minutes.
@BlueRidgeKat12 жыл бұрын
Where do you get the new lock washer thing?
@NukeBreath6 ай бұрын
Thanks for the video. I saw another video that helped me out also. Using a pair of vice grips. Using a pair of plyers made it easier for me. Squeezing the washer distorted it and made it a lot easier to then pry off.
@mickhill22093 жыл бұрын
How is he going to inflate the tyre. He`s put the wheel on the wrong way , the valve is now on the inside.
@TheGokartGuy
2 жыл бұрын
He installed a solid tire that uses no air .... Flat Free.
@whitewebshaunt4798 Жыл бұрын
YOU ARE THE MAN!!!! Thanks for this video.
@laurannaroach2559 Жыл бұрын
Ok smarty pants, you guys make it look so easy! Thank you for posting!
@stevebarratt42913 жыл бұрын
Love it man, saved me 10 minutes watching the guy that was figuring it out on camera...holy s#!t...
@gison8405
Жыл бұрын
fuuuuuuuuck - SERIOUSLY!!!
@hlittell Жыл бұрын
Fantastic. I guess I could have pryed it off, but the WD-40 and socket with the small claw hammer!! Thank you for posting this..
@nickh.38323 жыл бұрын
Worked like a charm .
@tbluemel2 жыл бұрын
Thank you VERY MUCH!
@rsgblue Жыл бұрын
Excellent , made it easy with correct tools and trick
@chasebrunner2 жыл бұрын
Appreciate It Brother !!!
@Planespotterdude2 жыл бұрын
Ty so much. These things tick me off, I’m replacing mine with the cap style nut
@jakecapshaw63915 ай бұрын
Thanks lol I needed that!
@anthonygonzalez281 Жыл бұрын
Perfect, how to video! Not all that extra yapping
@watchthesuit16832 жыл бұрын
Thank you!
@rocketrider1405 Жыл бұрын
What size socket did u you use to install that ‘ring’ at 1:23 ?
@joemcsorley15282 ай бұрын
fantastic! Thanks
@720ET4 ай бұрын
New tires look bigger, I like them. What size are new tires?
@user-yx9jg6lz5s Жыл бұрын
Do you remember what size socket you used to install that ‘ring?
@HectorCanon-fh9yi2 ай бұрын
me interesa me podría brindar información
@andreib.6189 ай бұрын
Hi . Where did you bought the new tires from and how much are they ? Thank you
@mtsanchez27 Жыл бұрын
Where did you buy the tires?
@viva76422 жыл бұрын
EXCELLENT!!
@BeatdownRevival Жыл бұрын
100% Excellent!!!
@lazerbro88473 жыл бұрын
I know how to seal the bead you put a strap around the dolly tire and you put air in it
@Castleknight2 жыл бұрын
Did a new push nut come with the replacement wheel?
@abbasjackson5459
2 жыл бұрын
No , it does not
@joehill801411 ай бұрын
excellent video.
@jorgefraiche5 ай бұрын
Thank you
@beetlerunner2 жыл бұрын
Ok so I did what you did and removed that little metal piece which allowed me to remote the tire but the metal piece broke in the process. So now I can’t secure the new tire. Suggestions?
@abbasjackson5459
2 жыл бұрын
Are you talking about the washer that i removed with the hammer? I think you can find them at home depot just bring the broken piece and show it to an associate .
@beetlerunner
2 жыл бұрын
@@abbasjackson5459 the first piece you removed. I found some on amazon thanks.
@biggerscranerealestategroup Жыл бұрын
Are dolly replacement wheels all the same size?
@erosh6012
Жыл бұрын
No depends on the dolly some are bigger
@carlosrivera46603 жыл бұрын
I cannot get that part of. How you doit. Please help?
@tacokiller5638
3 жыл бұрын
Just get two flat heads and try to pry it out.
@carlosrivera4660
3 жыл бұрын
@@tacokiller5638 thanks. I try that for one hour. It didn’t work. 🥲🥲 thanks anyway. 👍👍
@VeesFunkyAZZshop10 ай бұрын
found this video after i just got frustrated and bust to SH@# the entire tire and lost the fixtures
@awells58912 жыл бұрын
Thanks
@user-pl2ug3vd5d6 ай бұрын
Dude, You put the air stem on the inside.
@sevennumberss5 ай бұрын
You put the tire on backwards.
@ravenbonanza1522 Жыл бұрын
1:08 He put the wheel on the wrong orientation. That portion should be at the back side. How can you inflate the tire if the tire valve is on the back of the wheel?
@jasont7814
8 ай бұрын
No inner tube . Solid wheels.
@edaycock35052 жыл бұрын
Really doesn't matter which side the valve stem is on, but normally on the outside
@erosh6012
Жыл бұрын
There is no valve on this type tire. Its solid rubber type
@JesusRamirez-ho7cs2 жыл бұрын
Chingon👍
@EG-zl6bl9 ай бұрын
It's on backward!
@JoseTorres-st5ic Жыл бұрын
I would have put the new wheel with tit part down. Nice job though
@rajkumarghattri82742 жыл бұрын
chahekoo chha
@sikbot5 ай бұрын
I didn’t have that socket so I used a 17 wrench and I just kept going around with the hammer .. worked just fine. Thanks for the help
@glendaleclone638810 ай бұрын
Where is the origin of your name Abbasid?
@anthonymoreschi36727 ай бұрын
Broke my hammer....
@jerroldwrentz63954 ай бұрын
Obviously you don't know the difference between a whale and a tire.
Пікірлер: 75
a little too talkative for my taste, but extremely helpful!
@abbasjackson5459
2 жыл бұрын
Why would I bore you with bla bla bla when you can see it for yourself, Appreciate the coment
The circular clip comes off the shaft without all the prying if you simply grip it at the edge with waterpump (large) pliers and rotate it counter-clockwise. The tabs are slightly angled, so it will spin off like a nut. This trick saved me a ton of time and effort.
Dude, you’re a lifesaver. Worked like a charm. Tractor Supply tires, $14.99 each. Thank you!
I wish all how to videos were straight to the point like this. Excellent video! Thank you
Genius. Thank you for not talking for an hour to explain 2 steps. LOL
I'm 63 and I did it with a small crow bar, a hammer, and WD-40. Thank you. I replaced my flat tire with a "no flat" variety. (However, I'm whooped!)
@BlueRidgeKat1
2 жыл бұрын
You go girl !!!!!!!
Cool this is the first one that showed me how to get the cap off! Took me less than 5 minutes to do it. Thank you!
Thank you so much! This did the trick. I WD-40'd then used the claw of the hammer to remove. Hard part was finding the replacement locking washer at either Lowe's or Home Depot. Found them on Amazon as key words: Internal Tooth Starlock Washers, Push On Locking Washers, Speed Clips, Fasteners.
@briandimascio3624
8 ай бұрын
U can reuse the push nut. I used channel locks to deform the edges instead of a hammer and then bent it back with a small adjustable wrench while holding the other side w channel locks so it is too tight to slide over the axle. Find a socket that will clear the 1/2or 5/8” axle and hammer it over. The teeth will lock
Thank you the wheel was put on backwards, but still helpful.
@abbasjackson5459
2 жыл бұрын
On purpose
You tube videos have saved me 75.00 today, a guy was going to charge me to change the tire. Hod Bless U-tube
EXACTLY what I was looking for. Thank you!
This was perfect. I was able to change both wheels in less than 10 minutes.
Where do you get the new lock washer thing?
Thanks for the video. I saw another video that helped me out also. Using a pair of vice grips. Using a pair of plyers made it easier for me. Squeezing the washer distorted it and made it a lot easier to then pry off.
How is he going to inflate the tyre. He`s put the wheel on the wrong way , the valve is now on the inside.
@TheGokartGuy
2 жыл бұрын
He installed a solid tire that uses no air .... Flat Free.
YOU ARE THE MAN!!!! Thanks for this video.
Ok smarty pants, you guys make it look so easy! Thank you for posting!
Love it man, saved me 10 minutes watching the guy that was figuring it out on camera...holy s#!t...
@gison8405
Жыл бұрын
fuuuuuuuuck - SERIOUSLY!!!
Fantastic. I guess I could have pryed it off, but the WD-40 and socket with the small claw hammer!! Thank you for posting this..
Worked like a charm .
Thank you VERY MUCH!
Excellent , made it easy with correct tools and trick
Appreciate It Brother !!!
Ty so much. These things tick me off, I’m replacing mine with the cap style nut
Thanks lol I needed that!
Perfect, how to video! Not all that extra yapping
Thank you!
What size socket did u you use to install that ‘ring’ at 1:23 ?
fantastic! Thanks
New tires look bigger, I like them. What size are new tires?
Do you remember what size socket you used to install that ‘ring?
me interesa me podría brindar información
Hi . Where did you bought the new tires from and how much are they ? Thank you
Where did you buy the tires?
EXCELLENT!!
100% Excellent!!!
I know how to seal the bead you put a strap around the dolly tire and you put air in it
Did a new push nut come with the replacement wheel?
@abbasjackson5459
2 жыл бұрын
No , it does not
excellent video.
Thank you
Ok so I did what you did and removed that little metal piece which allowed me to remote the tire but the metal piece broke in the process. So now I can’t secure the new tire. Suggestions?
@abbasjackson5459
2 жыл бұрын
Are you talking about the washer that i removed with the hammer? I think you can find them at home depot just bring the broken piece and show it to an associate .
@beetlerunner
2 жыл бұрын
@@abbasjackson5459 the first piece you removed. I found some on amazon thanks.
Are dolly replacement wheels all the same size?
@erosh6012
Жыл бұрын
No depends on the dolly some are bigger
I cannot get that part of. How you doit. Please help?
@tacokiller5638
3 жыл бұрын
Just get two flat heads and try to pry it out.
@carlosrivera4660
3 жыл бұрын
@@tacokiller5638 thanks. I try that for one hour. It didn’t work. 🥲🥲 thanks anyway. 👍👍
found this video after i just got frustrated and bust to SH@# the entire tire and lost the fixtures
Thanks
Dude, You put the air stem on the inside.
You put the tire on backwards.
1:08 He put the wheel on the wrong orientation. That portion should be at the back side. How can you inflate the tire if the tire valve is on the back of the wheel?
@jasont7814
8 ай бұрын
No inner tube . Solid wheels.
Really doesn't matter which side the valve stem is on, but normally on the outside
@erosh6012
Жыл бұрын
There is no valve on this type tire. Its solid rubber type
Chingon👍
It's on backward!
I would have put the new wheel with tit part down. Nice job though
chahekoo chha
I didn’t have that socket so I used a 17 wrench and I just kept going around with the hammer .. worked just fine. Thanks for the help
Where is the origin of your name Abbasid?
Broke my hammer....
Obviously you don't know the difference between a whale and a tire.
@jerroldwrentz6395
4 ай бұрын
Wheel, stupid auto correct