Honestly the best bends I've seen from a diy brake. I was about to mount my hinges on top but I see the logic here. Great job

@DIYFixMan

2 жыл бұрын

Thank you very much my friend

Best diy brake I have seen.

@DIYFixMan

2 жыл бұрын

thanks 😊

Best DIY brake I’ve seen

well done brother! Thank you

Today I used a hammer, tomorrow I'm building this. Great project.

@DIYFixMan

7 ай бұрын

Thank you very much my friend

@cutweldngrind

7 ай бұрын

​@@DIYFixManI'm buying material to build 1 today finally.

Супер станок без сварки

Respect. You got a new subscriber.

@DIYFixMan

7 ай бұрын

Thank you very much my friend, I am very happy

Very nice bender!

Gracias por compartir

Отличная идея!

👍❤

פשוט מדהים! 👌

@DIYFixMan

5 жыл бұрын

תודה

Great video

good for bending polycarbonate too

@jamesgizasson

5 ай бұрын

I want to build one specifically for this reason! :)

ขอบคุณมาก

Amazing creativity

You stuff is awesome

@DIYFixMan

5 жыл бұрын

🤗❤️

Yep, another brake builder who get's it wrong and the people commenting haven't a clue so make inane comments about how good it is and the best video they've seen! The clamp bar on ALL brakes has to be able to slide way from the point of bend by the thickness of the metal being bent THEN clamped down! I've watched dozens of these videos and only seen one that got it right. One of them had to cut the video at the moment it couldn't reach 90 degrees because the clamp was fixed on the edge! He didn't mention it..... Fine if all you are going to do is bent the same thin tin all the time, it doesn't matter but if you were doing a production run of bends then you need adjustable stops that you can set for whichever thickness metal. It's not rocket science but sadly there are far too many people posting videos on YT for all kinds of things but who are of low intelligence.

@joaquintrash3450

Жыл бұрын

¿Can you post the link for the correct configuration? (for the clamp sliding bar)

@TDPEquinox

10 ай бұрын

This should be easily done by ovaling the holes that mount the clamp bar (on the table side), or adding multiple holes along the bar at different pre set distances. If you're that concerned about production runs, get a production brake. Or this simple mod does the same.

@barrynewton5587

9 ай бұрын

Hi Jonathan Can you give me the link for the " one who got it right "please as I need to build one of these?

За гайки с ушками - like.

👏👏👏👏

@DIYFixMan

5 жыл бұрын

Thanks

Hey other universe.. bite my shiny merel.. woops got the wrong bender... 😂

Excelente muy bueno saludos desde Argentina

@DIYFixMan

5 жыл бұрын

❤️

روعة

Very talent person

Mande as medidas da drobadeira quero fazer uma 2:20 por 1'50 pra dobrar chapa de 1'8

Very good 👍 👍 👍

@DIYFixMan

5 жыл бұрын

thanks buddy

Very nice, ThankQ

@DIYFixMan

5 жыл бұрын

Thanks 🤗

Very nice good job sir

@DIYFixMan

5 жыл бұрын

Thanks 🤗

С такой штукой я бы тоже гнул всё подряд 😀👍

Nice 👍

@DIYFixMan

5 жыл бұрын

Thank you 🤗

Pero como puedes trabajar sin guantes !!!

I guess... if your sheet metal is only 15" wide.

Si pero dobla una pieza de 20' ????

👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼

👏👏👏👏👏👏💖💖💖

@DIYFixMan

5 жыл бұрын

❤️❤️❤️❤️

too much free time my friend

из за рояльной петли там не будет 90 градусов

Достойно

can you gift detail specifications?

freezing / cooling down the aluminum to make it harder for a cleaner cut is something 99% of men fail to do

@dangerous8333

Жыл бұрын

Who cares. Plenty of ways to clean it up afterwards. Who has a freaking freezer in their shop.

А Федя ломик об каленку гнул

@DIYFixMan

5 жыл бұрын

Thank you 🤗

He must like radiation burns on his hands

Oui c bonne

No hay esa bisagras

@DIYFixMan

5 жыл бұрын

There are hinges

Ненужная херня. Тупо можно в тисках все загнуть.

👏👏👏👏

@DIYFixMan

5 жыл бұрын

Thanks