Timestamps: 00:00 Introduction 00:10 Why good Internet connectivity is important 00:52 How to properly set and lock 4G frequency bands 01:50 How to configure cellular band lock on Teltonika RUTX11 02:27 Generals tips for good LTE connectivity

@user-zx7ee6tr2h

4 жыл бұрын

I do not see in my rut950 option band select

@TeltonikaNetworks

4 жыл бұрын

Sorry for the long response time. You can find the option in Network -> Mobile -> General, and it will be under the Network Frequency Bands section. You must set the connection method from Auto to Manual.

Good video. The video production is good. They took a difficult optic and were able to take a dry topic and bring it to life.

@TeltonikaNetworks

4 жыл бұрын

Thank you!

Very easy to follow and great information. Thanks for creating this video.

@TeltonikaNetworks

3 жыл бұрын

Thank you for the positive feedback!

Great run down and info in band selection. Just wish my b315 b618 or smart modem 3 had an easy way to band select as they dont

Thank you for the enlightenment.

Thanks, I will try it !

@TeltonikaNetworks

Жыл бұрын

You are welcome!

I have just got my RUTX12 yesterday, so i'm gratefull for your videos. Can i ask you where i can fin all the documentation about my RUTX12 in english and better in French ?

@TeltonikaNetworks

3 жыл бұрын

We are glad you chose the RUTX12! You can find all the documentation here - wiki.teltonika-networks.com/view/RUTX12. If you have any questions, check our Crowd Support Forum - community.teltonika-networks.com/

hi, this was a great video, thanks for sharing with us. I am using tp-link and was having tough time having a good connection. So tried locking among 1,3,5 bands. It gets connected but I still see 30-40 seconds of ping timeouts intermittently. What could be the problem, network, the router, or something else?

@TeltonikaNetworks

3 жыл бұрын

First of all, you find out what your operator supports bands. Next, using a phone and cell connection apps, figure out which is the closest cell tower and what bands your phone uses to connect. Then you will be sure you are connecting to the correct bands, and you should get a better signal. Also, when pinging, make sure the target server is close to your location.

Hi, My internet speed becomes faster when I locked it into a specific band- thanks to you! 👍However does it consumes more data?

@TeltonikaNetworks

4 жыл бұрын

Thank you for your comment. With faster Internet speeds, your content will load faster, but the data consumption will remain the same.

@othman0077

2 жыл бұрын

me too I got faster speed test I locked to Band 3 because of FDM

Thank you for the video! Is there a physical switch where I can push on/off the wifi without logging in?

@TeltonikaNetworks

3 жыл бұрын

Hello. No, Teltonika Networks do not have physical WiFi switches. But you can have different configurations and, with the help of the calendar, load them, for example, WiFi ON during the day. And OFF during the night.

@E3CB

3 жыл бұрын

@@TeltonikaNetworks Wow! That is cool! Thank you.

I use RUT X11 in our boat. We travel around and get all type of different connections and bands. It would be great if Teltonika would have an option that check if GPS position is not moving after 10 minutes and then start to test different bands to see what station I should use. There is global speed test pages and API's to use for a solution like that. If you know any terminal/bash command I can change band with, I could code that solution myself. ( I already have some own code running on X11 for some of my projects)

@TeltonikaNetworks

2 жыл бұрын

Greetings, we have forwarded the suggestion to our development team. As for building a manual solution yourself, you could start looking at this topic: community.teltonika-networks.com/41048/what-is-wrong-with-this-cell-lock-command On our Crowd Support forum, you will be able to get more in-depth information and solutions.

I have issue with my failover switch from VSAT to mobile SIM network on RUT955. Please help me

How to lock to a specific Cell? Is there a field there to input prefered eNB i.e. to which the router should try to stick to?

@TeltonikaNetworks

3 жыл бұрын

Bank locking is usually enough to connect to the best tower. There is no option to connect to a specific cell.

@per.edstrom

3 жыл бұрын

@@TeltonikaNetworks We have sereral towers in the same direction in a Skiresort. A very low-angle Yagi might work but a lock on Cell ID would be useful anyway.

Good evening. Am living in Jamaica and I use Digicel. However, Digicel Jamaica used 4G LTE 700mhz band 17. So please help me on which device I can purchase online to use?

@TeltonikaNetworks

4 жыл бұрын

Greetings. Unfortunately we currently do not have any device that can operate on LTE Band 17. You can find all the frequency bands supported by different Teltonika Networking products in this page: wiki.teltonika-networks.com/view/Frequency_Bands

Locking bands is critical for consistency on 2/3 providers in my market

@TeltonikaNetworks

3 жыл бұрын

That is why we think it's an essential feature in Teltonika Networks devices.

I cannot find this setting with the newest update. Where is the band selection setting located now? I just purchased this rutx11 and I'm new to the ui

@TeltonikaNetworks

3 жыл бұрын

Hello, the UI and the setting location is still the same, nothing changed. Make sure you have Advanced Mode enabled in the WebUI settings - wiki.teltonika-networks.com/view/RUTX11_Mobile

2:32 - is that frequency matched with those band number are fix and remain same on other country?

@TeltonikaNetworks

2 жыл бұрын

In different countries, different providers use various bands. Here you find more information on frequency bands of the Teltonika Networks devices: wiki.teltonika-networks.com/view/Frequency_Bands If you are traveling from one country to another, you must ensure that the band is used in that particular country.

@AyieRamle2

2 жыл бұрын

@@TeltonikaNetworks - Wow! Really appreciate your response and thanks alot for that link. Have a good day.

Hello great video. I have a X11 getting fairly good signal and down (30)and up (7),speeds. Better than ISP provided 5/2 speeds on their modem. Problem is even with 5x the download now Netflix and Peloton workouts buffering like crazy. Never happened on ISP modem. Any suggestions. FYI X11 on pass-through. As we have a Ubiquiti Dream Machine Pro as main router ( same and with ISP (modem) although ISP modem did not have ability to provide pass-through or bridge. So it was double NAT

@TeltonikaNetworks

2 жыл бұрын

Hello. You can enable Passthrough on RUTX11 - wiki.teltonika-networks.com/view/RUTX11_WAN#Mobile:_General_Settings In Mobile: General Settings - select Mode as Passthrough.

@dennisdelorme

2 жыл бұрын

Sorry I was trying to ask what’s the purpose of pass-through vs bridge node pro cons etc.

possible to lock different band for upload and download for example i am need use band B40 For Download And Band B3 FOr Upload ? Thanks

@TeltonikaNetworks

3 жыл бұрын

No, it is not possible. You set your LTE modem to work on a specific band so everything will work on the same band. Unless you are using a device like RUTX12 which has two modems: teltonika-networks.com/product/rutx12/

Hi good day,can u pls help me where i can find the band in my modem i had dwr-m960 modem dlink..how can i lock the ty and keep safe

@TeltonikaNetworks

3 жыл бұрын

Greetings, I would suggest to start with manual for your device. Also try the D-Link support forum.

How can I add custom APN on rut240 for bypass hotspot limit ?

@TeltonikaNetworks

2 жыл бұрын

Hello. To set a custom APN refer to our Wiki page: wiki.teltonika-networks.com/view/RUT240_Mobile#Mobile_Configuration

For mobile solutions... I really wish someone would create an app that would detect the best band and select that one VS the closest band that may be near capacity. Sometimes a worse signal but better throughput may be the best solution

@level8473

8 ай бұрын

That's not really practical, since the "best" band rn would'nt be the best band later as it gets congested

Trying to do the lock with my RUTX11 with firmware RUTX_R_00.07.02.7 and I do not see Bandwidth option in Mobile settings under either General or SIM Switch. Any thoughts?

@michaelsperry8320

Жыл бұрын

Found it!!!! Need to turn on Advanced before you can see the Bandwidth Setup.

@TeltonikaNetworks

Жыл бұрын

Great! Glad you were able to figure it out. Enabling the advanced settings can enables a lot of options and settings.

We had problems with RTU240 connection and control, tried to reach Teltonika by numbers that was on package and in internet page, but nobody answer...

@TeltonikaNetworks

2 жыл бұрын

For technical support please use the following resources we provide - teltonika-networks.com/after-sales-support-service/

Can I select a few or just one at a time?

@TeltonikaNetworks

2 жыл бұрын

You should experiment with selections on which bands give you the best results. Selecting one band will force the device to use that specific band. Selecting several will allow switching between them.

@Teltonika Hello, it is possible to lock 5G NSA band on RUTX50?

@TeltonikaNetworks

Жыл бұрын

The term "NSA band" refers to "non-standalone" 5G, which means that it uses existing 4G infrastructure to provide 5G services. And there a multiple bands thant for example work with RUTX50 - 5G NR NSA: n1, n3, n5, n7, n8, n20, n28, n38, n40, n41, n77, n78 So, you can lock to a specific band as described in the video.

Is there any option to insert sim card?

@TeltonikaNetworks

3 жыл бұрын

Yes. Almost all Teltonika Networks devices have an option to insert SIM cards. You can find all the information here: teltonika-networks.com/products/

Hi, is band locking possible in Tenda 4G680?

@TeltonikaNetworks

2 жыл бұрын

Greetings. We only can answer questions regarding Teltonika Networks devices. Contact your device manufacturer for more information.

Hallo! I have a TRB 140 and there is no such option here. Can you help me? sms would be sent from http, on 4g it doesn't go out or you have to wait a long time, on 2g the message goes relatively faster, but it's still slow.

@TeltonikaNetworks

7 ай бұрын

Could you please reach out to our engineering team on the Community Support Forum (community.teltonika.lt/)? They would be more than happy to assist you.

@laszlototh4417

7 ай бұрын

@@TeltonikaNetworks thank you, I found that the advanced option was needed, there are more options here, I will try them. However, what I don't understand is that the (Modem) data connection shows disconnect, but the sms goes out.. how do I set it to connected

Been doing this for a Huawei modem which is lock to a Network carrier. We just need the admin password to change it and for that we need pay for it.

@TeltonikaNetworks

2 жыл бұрын

Greeting. We can't comment on any other manufacturer devices, but for Teltonika Networks equipment, these changes are simple and straightforward.

hello- do you have a product that is comparable to something like the NETGEAR Nighthawk M5 5G Mobile Hotspot with WiFi 6 (MR5200) I would like to tether 5g from my mobile carrier (tmobile) to my pc via ethernet- i am concerned about tmobile blocking devices like this on their network however since they offer their own 'home internet gateway' product that competes with devices such as the ones you are selling.

@TeltonikaNetworks

2 жыл бұрын

Hello. We plan to release devices supporting these technologies in the future.

Where to buy? In India

@TeltonikaNetworks

3 жыл бұрын

You should search your local retailers for Teltonika Networks devices. Or you can contact our offices here - teltonika-networks.com/about-us/contacts/

@bigzonetechnology5974

3 жыл бұрын

Hi, we have 4G lte wifi router with band lock and reapeter mode feature. If you are still looking for the same please call or whatsapp us at 7049777666 www.bigzonetech.com

Why i have locked in band 3 for long time. Its good connection. But suddenly it loses connection But i switch to band 28 and i got connection. It is the same ISP. Only band 3 lose connection. What is the reason?

@TeltonikaNetworks

Жыл бұрын

There could be several reasons why you were experiencing such issues. It can be affected by interference from other devices or it is also possible that there may be network congestion, which can occur during peak usage times.

how come a phone usually have a more stable connection than your router?

@richiguru7564

8 ай бұрын

I disabled data roaming and this increased my connection stability by huge amount

Any android app that can measure and determine what is the best and stable network band？I have two unit of RUT240, the speed is big different with my mobile speed. Appreciate if anyone can share the app and troubleshooting method. Thanks😊

@TeltonikaNetworks

Жыл бұрын

Sadly, we cannot recommend a specific app for network measurement; however, a quick online search should yield plenty of options for you to choose from. Concerning your RUT240 units, we advise keeping the firmware up to date to benefit from the latest improvements and fixes. It is also important to ensure your device is located in an optimal position for the best signal coverage. Lastly, enabling the software offloading in your firewall settings may boost network performance. Hope it helps!

@siowxsen

Жыл бұрын

@@TeltonikaNetworks can share the steps to enable the offload at firewall？

@TeltonikaNetworks

Жыл бұрын

@@siowxsen To enable the software offloading navigate to device WebUI -> Network -> Firewall -> General settings, there you should see the Routing/NAT offloading

Can u change imei with this router?

@TeltonikaNetworks

2 жыл бұрын

No

No wonder USA hate Huawei. they can make Router with CAT 19 easily. the problem is their Chip basically reverse engineering with added modular extension from Qualcomm chip.

Anyone know how to lock in a specific band on a new Samsung S22 plus phone? I was using Samsung Band Select, but since the last security update it won't allow me to access it. A window pops up and says: ERROR: Hidden Network Settings activity not found on device. This was a great tool until Samsung screwed it up for us.

@TeltonikaNetworks

Жыл бұрын

We are only able provide technical information regarding Teltonika Networks devices.

can i just lock only one band?

@TeltonikaNetworks

3 жыл бұрын

Greetings. You can select one or several bands according to your specific use-case.

This cut me off the internet and I can't get back on now. I wish I had left it on auto. One full day and still the RUTX11 isn't set up. I really am unhappy after all this money I spent

@TeltonikaNetworks

Жыл бұрын

Thank you for the comment. We would be more than happy to help you - we just need more details about this issue. You are welcome to fill out our contact form (link below) and tell us more, and our support team will get back to you promptly. teltonika-networks.com/about-us/contacts

@mymobile5014

Жыл бұрын

@@TeltonikaNetworks You're more than happy to help if I bought from you, but if I got from a supplier than I have to use the online forum which sits with thousands of unanswered questions. Grrrr

How locked bands on Mobile Phone please Make video

@TeltonikaNetworks

2 жыл бұрын

Thank you for your suggestion. But Teltonika Networks specializes in other technology fields.

there is no reason to connect to the highest frequency band just because it is the highest frequency band. What matters is available bandwidth and congestion, you didn't make that clear.

@TeltonikaNetworks

Жыл бұрын

Thank you for your comment.

@paulmitchell4421

Жыл бұрын

@@TeltonikaNetworks non sequitur