Good vids, keep up the good work 👍

Thank you so much for making this video, would be a hard time to figuring out how to get it back in there

Did just change the bushings in mine it was a huge difference 👍

I recently replaced mine with superpro front control arm, feel amazing too💪🏻💪🏻

Great video man. I've swapped subframe to the ally S3 recently, now onto my third set of control arms, from stock steel (then put on whiteline caster/camber top mounts = great option!), to chinese ally with knock off camber adjustable ball joints (worked fine but didn't get me enough camber close to that of stock ie. max 1.25 neg, could only get a min of 2.3 neg, didn't met local laws i.e. no more than 0.5 deg neg more than stock = 1.75 neg.), to whiteline ones as you have with whiteline roll centre camber adjustable ball joints, meeting local laws ). Last swap I didn't lower the subframe with the one time torque to yield bolts, I removed the gearbox mount below the battery and gently jacked up the box from underneath, it got me the clearance I needed for the front right control arm bolt and possibly/probably easier. Also threw in the subframe deadset lock kit earlier on and didnt want to buy new bolts etc and the hassle of getting the subframe lock kit back in perfectly. Perhaps a tip for those that dont know. Great vid tho, cars looking great! Must say, camber is good, but getting more caster is better. PS, yes rear bolt first for the control arms! Found that out too... Im running 255/30/19 Michelin PS4s on 8.5" +45 et, on 8 piston Lambo brakes and there is clearance, inner plastic guards need work, but in the dry I can power out of corners with rear drift (rears are 235/35/19 Semi slicks aka RS3 offset tire sizes))

@TheEddysGarage

Жыл бұрын

Awesome tips and your car sounds like a beast!

Useful videos, considering the cost should defo add that to my to do list.

Good stuff 👍 Could remove the Dogbone mount bolts and use a piece of cloth on a pry-bar to rock the trans forward enough to remove the driver's side bolt 👍 Also, a good time to utilize a Subframe Locking Collar kit 👌

@TheEddysGarage

6 ай бұрын

Yes I did the subframe locking kit when I dropped it to install the front swaybar. Did you see that video?

@MegaHollywood1971

6 ай бұрын

@@TheEddysGarage No, unfortunately. I didn't see that one. Didn't look at all your posts yet.

You instilled me to install them.

@TheEddysGarage

3 жыл бұрын

Wasn’t too hard

I have the same LCA's for over a year now, love them! Not just the better grip, but also improved steering feel with the added caster. Some believe they limit tire options, but I run 255/35 18's no problem, I did have to do some slight modification to the wheel well liner, basically tie wraps to have it hang a bit higher and some reshaping with a heat gun, but not bad at all really. They can fit with no rub at all, in fact I think I could maybe fit a 265, but it would be tight. Does that extra 20 mm of tire give a significant improvement in grip and handling? Oh yes, it is a big improvement. I did not realize just how much until I bent a rim and had to put my old 235/35 19's back on with the exact same tire/condition. I knew the 255's were better, but i did not really appreciate just how much until switching back; cornering at speeds where I was not even close to the limit with the 255's had the tires squealing and sliding with the 235's. I had to re-calibrate my speed/grip expectations even for street driving. I have a Golf with the steal sub frame, they went in with no issues at all. I also completely dropped the sub frame and did the sway bar and a dead set kit all at the same time, so that might be a factor, or maybe slight differences between aluminum vs steal sub-frames?

Not to add insult to injury, but may help others, super pro have brought a full handling kit out costs £1,500 (you muricans can do the conversion) so if you do it all at once it will save you a lot of pain getting multiple alignments done and faffing about getting up and down on the jacks ☺️✌🏻

Nice! Are these new control arms noisy?

@TheEddysGarage

3 жыл бұрын

I had no difference in noise

What are the torque specs please?

@TheEddysGarage

2 жыл бұрын

Not sure sorry. A quick google search and I found ECS have it listed in their instructions blog.ecstuning.com/vw-mk7-golf-ecs-performance-control-arm-kit-installation-instructions/

Oh and I made the mistake of procrastinating on getting the alignment done after installation,, and ended up driving about 1500 miles, don't do that. The car drove fine but these LCA's cause a huge amount of toe out and will wear your tires down extremely fast. After that experience, is when i made my own alignment rig and started experimenting.

@gregnm240

3 жыл бұрын

Do you happen to know your alignment specs after installing your bushings? I installed super pro bushings in my front lca's and I came out to about 7.8 caster

@ericmichel3857

3 жыл бұрын

@@gregnm240 Just a hair under 9 degrees, 8.9 and 8.7 to be exact.