I used your video and replaced the stabilizer rods in my Samsung washing machine with the help of my daughter. Somethings were a little different but we figured them out. Thank you for the tip on taking pictures before taking things apart. That was a life saver. My washer works like a charm again. I am a single mom and you saved me a lot of money. ❤

@chana7141

11 ай бұрын

Did you have the same washing machine? I have the same exact one and I need to do something because it's constantly off balance now 😢

@DIYRepairsNow

11 ай бұрын

You’re welcome thanks for watching my video👍🏻👍🏻💯💯

@afterthought72

9 ай бұрын

How much did it cost to replace them

@MS-nq7uy

3 ай бұрын

@@afterthought72 $45 Amazon. Parts in 2 days.

I followed your instructions and installed the new shocks in about an hour in total. Working great now and now I know how to do this. I looked at five other videos and yours was the most accurate and helpful. Thank you!

@DIYRepairsNow

6 ай бұрын

You’re welcome thanks for watching my video💯💯👍🏻👍🏻

Thank you so much for this! My husband is a good handyman but not a washing machine repairman. He watched your video, ordered the part from Amazon, and then used your video as a guide. Washer is now working great. No more off balance. So thank you!!!

@DIYRepairsNow

2 ай бұрын

I am Happy to hear My Video Helped Your Husband Fix Your Washer! 👍🏻👍🏻 Thanks For Watching!

Best walkthrough DIY repair YT video I've seen in a very long time. Simple to follow, excellent. Thanks!

@DIYRepairsNow

6 ай бұрын

Glad you liked it! Thanks For the Support!

Yes, after replacing the shock absorbers (armsprings) of a Samsung washing machine, it is necessary to perform calibration. This will help bring the device up to speed with the new components and correctly recognize load balancing. To perform calibration, follow these steps: 1. Make sure the drum is empty. It is important that there is no laundry in the car. 2. Close the door. 3. Turn off the power. 4. Press and hold the Temp and Delay End button at the same time, return the power without releasing the button. 5. You will see the indicators light up, continue to press the buttons for 3 seconds. 6. The machine will then enter calibration mode. Wait for the process to complete (usually takes about 3 minutes) and the machine will turn off automatically. After calibration is completed, the device should work normally. If the problem persists, there may be a problem with the balance sensor, motor, or electronic control. In addition, the Samsung manual indicates that the Ub error may pop up if the drum is not loaded evenly. I advise you to make sure that the client loads laundry into the drum correctly. Hope this helps!

@garryweber4199

7 ай бұрын

I did the repair. It was a lot simpler than I expected. I put a load of laundry in and it kept filling like to where it almost overflowed so I emptied it, drained the water and did a calibration but it still is over filling. Any ideas ??

@user-js5zf8xq1d

7 ай бұрын

@@garryweber4199 water level sensor

Totally fixed my problem, Samsung repair guy said it would cost between $300 and $500 to fix the issue. I ordered the parts off Amazon for $50. I then followed the steps in your video! Thanks my friend

@DIYRepairsNow

9 ай бұрын

Glad My Video Helped you Repair it Yourself and Save Money, That’s My Goal! Thanks For Watching!

Good morning I'm from Miami dade and was having issues with my washer as u explained In the video. I ordered the parts from your link they came right away. I had my drill and followed your directions. My wife so happy now it really solved the banging problem and being off balance. I just wanna thank you and say I appreciate u and this video. Saved a ton of money doing it myself GOD BLESS... CMV ‼️

@DIYRepairsNow

5 ай бұрын

You’re welcome thanks for watching my video👍🏻👍🏻💯💯

Incredible video! I followed your guidance exactly and used the suggested springs to fix my washer. Samsung wanted $300 just for a diagnostic, which would not have been of much use anyway. I found the video on how to run the auto diagnostic in 30 sec. It's just a series of button presses. No local technician would touch the washer either. I decided to try the suspension replacement and now I have a washer running like new. Way cheaper and far less wasteful than getting a new washer. Thank you so much! ❤

@DIYRepairsNow

Ай бұрын

You are Very Welcome! So Happy to Hear My Video Was Helpful to you! Thanks for the Support!!!

Your instructions were exactly on point and made our DIY repair easier. We have the exact washer with the exact balance issues you described. I bought the rods (under $50) from your link, followed your video step by step and the washer is working as new again! I looked at several other instructional videos for this washer repair, and yours was by far the easiest to follow and understand. Thanks.

@DIYRepairsNow

3 ай бұрын

Happy to Hear My Video Helped With Your Washer Repair!

Hello. Great instructions. Now I’ve replaced the rods. And a week later. I’m back to constant off balance. Any ideas

Great video and explanations!! I replaced mine tonight by myself, and it took about 25 minutes total watching your video and doing the work at the same time. Thank you!

@DIYRepairsNow

2 ай бұрын

Glad it helped! Thanks for Watching!

Just want to say thank you for this video! I watched this a couple of times and was able to replace the stabilizer rods in 30 minutes. Thank you and happy holidays.

@DIYRepairsNow

7 ай бұрын

I am Glad to hear My Video Helped, It Means A lot! Thanks for Watching and Happy New Year!

What a lifesaver. Video was long, but I think it was necessary to explain all the details to look out for keep it up.

Thank you man. I bought the items you had in the description and installed them the way you showed in the video. Thanks for saving me a ton of money.

@DIYRepairsNow

2 ай бұрын

No problem 👍 I am Glad My Video Was Helpful to You. Thanks for Watching.

Great video. Thanks for showing about disconnecting and connecting the wires in the back right side.

This DYI saved me a lot of money. BIG THANKS!!

@DIYRepairsNow

Ай бұрын

Glad I could help!

Thank you for this video. You are a great teacher! We ordered the parts today!

@DIYRepairsNow

Ай бұрын

Glad it was helpful! Thank you for the Support!

Took a chance after watching your video- took a half hour washer works like new thank you

@DIYRepairsNow

4 ай бұрын

Great job! I am Glad My Video Was Helpful, Thanks for Watching!

Dude what a nice and well explained video. Save me a lot a money

Thank you so much for this very informative video. This helped me to fix our washing machine - now it’s running great! Very detailed step by step guide.

@DIYRepairsNow

4 ай бұрын

Glad My Video Was Helpful to you1 Thanks for Watching!

Thank you! I have the same washer same problem thanks to your video is fixed!!😊😊😊😊😊😊😊

@DIYRepairsNow

Ай бұрын

Happy to Help! 👍🏻

I replaced my suspension rods on my Samsung washing machine and 2 weeks later started to be unbalanced again and making loud sounds. Please help!

This was exactly the help I needed. Problem solved. Thank you very much for taking the time to make this video.

@DIYRepairsNow

2 ай бұрын

You’re Welcome! Happy to hear My Video was Helpful. 😁

A lil advice. To balance these washers turn on power, press temp and delay end together for 3 seconds then press start. It will put the washer in balance mode.

Thanks brother. I used this video and was able to change out the suspension rods no problem! I didn’t remove the rear metal panel and only unplugged two wires. The wire leading to the digital panel and the one leading to the back of the top plastic panel. A lot easier when you have an extra pair of hands. Just be careful when pulling the top up off the washer, (some connected wires and tubing). Overall, not too difficult!

Thank you brother, very concise instructions very helpful. Those spring rods a very gooey and sticky. You were right about them . Merry Christmas.

@DIYRepairsNow

8 ай бұрын

You’re welcome merry Christmas to you and your loved ones. Thanks for watching my video.👍🏻👍🏻💯💯

Wow great instructional video! Ordering the parts now!

Great video; thanks for the help. The project went smoothly.

Perfect step by step directions! Thanks!

@DIYRepairsNow

Ай бұрын

You're welcome! Glad My Video was Helpful!

Excellent video - im thinking this could be my problem but was frustrated because the washer is not very old. Keep up the good work

@DIYRepairsNow

4 ай бұрын

I am Glad my Video Helps, Thanks for Watching!

Awesome video. Great communication. Thank you so much as my wife is super happy now

@DIYRepairsNow

4 ай бұрын

Glad I could help! Thanks for Watching!

Thank you so much!! Totally fixed my problem, now I can wash at home again! 😊

Excellent video. Completed install of new shocks BUT the instead of the drum banging around, the entire machine now dances around and becomes unbalanced. Any tips besides never buying a Samsung washer again?

Thanks! Very complete and knowledgeable. Great Help! Saved BIG MONEY!

@DIYRepairsNow

7 ай бұрын

Glad My Video Was Able to Help! Thank You Very Much for Your Support, it is very much appreciated!

You are a lifesaver, my friend! I was ready to buy a new washer but you showed me how to fix it for $40. Is there any way I can send you a tip as a thank you?

@DIYRepairsNow

7 ай бұрын

You are Very Welcome, I am Glad to Hear My Video Helped! I have linked ways you can send a tip in the description of the video. Thank You so Much For Watching and For the Support!

Dude, thanks. Watch video and did this job. Made it easy, and worked great. Thanks

@DIYRepairsNow

4 ай бұрын

Great to hear! Thanks to Watching!

These are great instructions and tomorrow I am going to replace the rods on my washer. But I have a question - Where does the spring end of the rod attach to? Is it to the bottom of the drum?

@DIYRepairsNow

Ай бұрын

It Would be to the Bottom of the Outer Tub.

Very good instucyional DIY video! Thank you

@DIYRepairsNow

3 ай бұрын

Glad you enjoyed it! Thanks for Watching!

Super helpful - able to do perfectly with your help. Many thanks

@DIYRepairsNow

8 ай бұрын

Great to Hear! Glad My Video Was Able to Help You!

What happens if the rods were changed but the washer still shakes during spin cycle? Could it be something else other than bad installation?

@rebeccabazaldua4683

9 ай бұрын

Ok I replaced and it’s the same ..my washer is only almost 2 Yrs old

@stanleywheeler404

8 ай бұрын

​@@rebeccabazaldua4683there is a recall on these samsung washers some guy just posted the info on that. I'm calling Samsung corporate office about this recall they issued.

I have the same Samsung washing machine I change those rods out put it back together and it still knocking against the tub, so what else can I look at that it could be the problem? By the way I did put dampening Grease on those components before I install them I seen another videos saying that sticky stuff has to be on there in order for it to stop knocking completely. But it's still knocking can you help me out with that?

Question, the washer model I have is different from what I'm seeing online in parts #'s and in KZread videos. I have a samsung active water jet WA50t530 Is it that the parts were upgraded?? Any help? Thanks

I replaced mine but it’s still shaking ? What did I do wrong? Also my tube looks like my tube is not leveled.

Any other ideas on what it could be?

Thanks brother!!!

@DIYRepairsNow

10 ай бұрын

You’re Welcome! Thanks For Watching my Video!

Could it be the shocks even though it spins fine when it's empty?

I have a Samsung washer that won’t spin, it’s trying to spin but isn’t quite catching the washing basket. Any idea what might cause this or where I should be looking for more information?

What can I say that all the other positive comments haven't already said? Thank You!

@DIYRepairsNow

3 ай бұрын

Thank you too! Happy to Hear My Video Was Helpful!

Thanks!

@DIYRepairsNow

Ай бұрын

You’re Welcome! I am glad to hear that My Video Helped you Fix your Samsung Washer. Thanks So Much for the Tip and Support It is Truly Appreciates!

We did this repair just this morning. Unfortunately, our washer is still getting out of balance. The banging isn't nearly as bad, but we're getting the unbalanced code. Any suggestions?

@corrineelgin7860

5 ай бұрын

im having the same issue. Did you find a resolution?

Mine has no delay button. I replaced rods mo problem but still getting off balance

None of the suspension rods looked damaged?

@DIYRepairsNow

11 ай бұрын

They will never look damage, and in this model is hard to tell when they are bad sometimes when you push the drum and tub down in a bounce more than once that means the shocks are bad, but sometimes in this Samsung’s it doesn’t do it however, I’m going to leave you this link that way you see how it will bounce if they are bad. The only thing is that the link is from a whirlpool but it’s similar issue

@DIYRepairsNow

11 ай бұрын

kzread.info/dash/bejne/eqqI09imj7q0eLQ.htmlsi=CvgSUsy4hTvuPPTe

Tried replacing the rods and calibrated the drum and it still bangs around like crazy 😫

I have a lot of Samsung stuff. I like all if it. Appliance guy said stay away from their washing machines.

Literally replaced the suspension rods & it was back to the same error the next day.

I changed the shocks 2x . This washer needs to be loaded extremely carefully to have equal weight on all sides. I usually have to wash every load 3x to get it to run without unbalancing . Do not purchase this!

This Samsung washer had a recall for 2021, 2022. I bought mine new in june 2021 and 2 yrs later its doing tge same thing it wont spin tge water out. I just heard about this recall and i am calling the appliance store where i bought my samsung washer and i will be telling them about that recall on these samsung washers and i will ask them why didnt they tell us about these recalls. I will tell them that i am calling samsung about their recall and they better refund me my money or they will give me a new washing machine or i will call my attorney to go after them for fraud.

@TripleB23

7 ай бұрын

Curious, what became of your situation? With the recall, any progress?