Replacing mixer grinder coupler in 2 minutes. New coupler cost just Rs 10 to Rs 20
Жүктеу.....
Пікірлер: 69
@satyasanasi67882 жыл бұрын
Good sharing info. Actually its easy to open the coupler by placing the screwdriver in the hole or gap so the screwdriver will be same level with coupler and easy to open.
@janetdianzingazola33433 жыл бұрын
Thanks very much it help my husband doesn't want to fix it
@techieezchannel3265
3 жыл бұрын
Thank you very much
@SilambarasanVelu5 ай бұрын
Good video, it saved my time and money
@nikitah72223 жыл бұрын
Thanks a lot. With your help i could fix my Coupler within seconds.
@techieezchannel3265
3 жыл бұрын
Thank you
@lokeshwaranparandhaman5674 жыл бұрын
Was wondering if the bush was a screw type but this video was help full to know it was just the push type. But there is better way to pull the broken bush out rather trying to tweaking from the top. There is a open slit in through where we can get the screw driver to the bottom of the bush in a straight angle. Makes the job easier.
@nithiyarajavivekanandhan61923 жыл бұрын
Thank you very much. It was very helpful.
@techieezchannel3265
3 жыл бұрын
Thank you
@TheSunithanaidu4 жыл бұрын
Thank you so much. Great help!
@techieezchannel3265
3 жыл бұрын
Thankx
@hebzijos80048 ай бұрын
Pigeon 6teeth cubler 6teeth coupler jar was dameged so should it be 4teeth coupler replacement instead can you use it?pls ans me
@MOBILEPHOTOGRAPHYSTUDIO4 жыл бұрын
Tanx bro..100% working👍
@techieezchannel3265
2 жыл бұрын
Great , thanks
@yanipidathala32603 жыл бұрын
Thnk u for the video , it helped me a lot
@techieezchannel3265
3 жыл бұрын
Thank you
@shebijoshi13702 жыл бұрын
Thanks for your valuable information 👍
@techieezchannel3265
2 жыл бұрын
So nice of you
@ashar11822 жыл бұрын
Thanks for the great solution. while grinding in small jar it spilled everywhere. middle and big jar will shake and slightly rotate in groove when grinding. can you please help me in solving this problem, if you know any solutiion. My mixer is preeti eco plus and it is too noisy. Thanks in advance
@chandru1632 жыл бұрын
Superb music 💐👌👌👌use full video thanks 🙏
@techieezchannel3265
2 жыл бұрын
Thanks
@gulnazbegumgulnazbegum9660 Жыл бұрын
Thank u so much 💕
@soosangeorge7986 Жыл бұрын
Thank you
@majharalam42484 жыл бұрын
nice
@kalpanaramasamy74113 ай бұрын
Where can i buy this?
@sumansarkar-lf1qz10 ай бұрын
Thank you ❤❤❤
@jawidnazir4 жыл бұрын
Thank you very useful
@techieezchannel3265
3 жыл бұрын
Thanks
@majharalam42484 жыл бұрын
Tussi Great Ho
@techieezchannel3265
3 жыл бұрын
Thanks
@elle83883 жыл бұрын
Are couplers the same size for all mixers /mixer grinders?
@techieezchannel3265
3 жыл бұрын
No, it will be different for each brand mostly
@DINESHKUMAR-rw5ff3 жыл бұрын
Super thanks
@techieezchannel3265
2 жыл бұрын
Welcome
@druvaj4 жыл бұрын
Thank you so much
@techieezchannel3265
3 жыл бұрын
Thanks
@chakrapanimayakuntla583 жыл бұрын
Thank you!
@techieezchannel3265
2 жыл бұрын
You're welcome!
@muthupaul86094 жыл бұрын
How to know thread type or pressing type coupler
@SwingMotor
3 жыл бұрын
H bhai kaise
@manikalyani4 жыл бұрын
Thankyou
@techieezchannel3265
3 жыл бұрын
Thanks
@0x-X-x02 жыл бұрын
Thanks
@techieezchannel3265
2 жыл бұрын
Welcome
@AnkurThakur3 жыл бұрын
Nice
@techieezchannel3265
3 жыл бұрын
Thanks
@rimomathew9620
3 жыл бұрын
Thank you very much
@Garry_73 жыл бұрын
I’m having Philip mixer uska bhi aise he khulega?
@techieezchannel3265
3 жыл бұрын
Mostly it will be pressing type, thread types are not used these days
@Garry_7
3 жыл бұрын
Techieez Channel it was thread type when I took it to shop merse khula he nahi 😅
@poojachaturvedi29713 жыл бұрын
My coupler is broken on small part is left in centre how shall I remove it...
@techieezchannel3265
3 жыл бұрын
You can use plier to remove it
@poojachaturvedi29713 жыл бұрын
My coupler is completely broken on in centre it’s left little bit..
@techieezchannel3265
3 жыл бұрын
You can use plier to remove the small portion
@ryanfransjak3 жыл бұрын
Philipsmixer motor coupler tried to remove it but its not coming out.can you post a video please.
@techieezchannel3265
3 жыл бұрын
I Willl try
@m.sandeepchandra25442 жыл бұрын
Couplers are going with in 2 days changed 3 couplers with in 10days how to over come this
@mohammednuman1650
2 жыл бұрын
Bro befor placing the jar on the grinder please check the jar blade by hand whether it is spinning freerly or not then attach the jar to the grinder this little effort keeps you happy. Hope will satisfy by the answer☺
@techieezchannel3265
2 жыл бұрын
Please verify jar fits perfectly, you can also observe if you get more noise...
@bikrammundchhina3 жыл бұрын
Oder link please...
@techieezchannel3265
3 жыл бұрын
Which link sir
@techieezchannel3265
3 жыл бұрын
Just sample link... But you get it much cheaper rate at local store.... Preethi Coupler Mixer/Grinder Motor Coupler by Preethi www.amazon.in/dp/B00H0ELC1A/ref=cm_sw_r_em_apa_fabc_0F10K3EC9QH5YC2V6J9H
Пікірлер: 69
Good sharing info. Actually its easy to open the coupler by placing the screwdriver in the hole or gap so the screwdriver will be same level with coupler and easy to open.
Thanks very much it help my husband doesn't want to fix it
@techieezchannel3265
3 жыл бұрын
Thank you very much
Good video, it saved my time and money
Thanks a lot. With your help i could fix my Coupler within seconds.
@techieezchannel3265
3 жыл бұрын
Thank you
Was wondering if the bush was a screw type but this video was help full to know it was just the push type. But there is better way to pull the broken bush out rather trying to tweaking from the top. There is a open slit in through where we can get the screw driver to the bottom of the bush in a straight angle. Makes the job easier.
Thank you very much. It was very helpful.
@techieezchannel3265
3 жыл бұрын
Thank you
Thank you so much. Great help!
@techieezchannel3265
3 жыл бұрын
Thankx
Pigeon 6teeth cubler 6teeth coupler jar was dameged so should it be 4teeth coupler replacement instead can you use it?pls ans me
Tanx bro..100% working👍
@techieezchannel3265
2 жыл бұрын
Great , thanks
Thnk u for the video , it helped me a lot
@techieezchannel3265
3 жыл бұрын
Thank you
Thanks for your valuable information 👍
@techieezchannel3265
2 жыл бұрын
So nice of you
Thanks for the great solution. while grinding in small jar it spilled everywhere. middle and big jar will shake and slightly rotate in groove when grinding. can you please help me in solving this problem, if you know any solutiion. My mixer is preeti eco plus and it is too noisy. Thanks in advance
Superb music 💐👌👌👌use full video thanks 🙏
@techieezchannel3265
2 жыл бұрын
Thanks
Thank u so much 💕
Thank you
nice
Where can i buy this?
Thank you ❤❤❤
Thank you very useful
@techieezchannel3265
3 жыл бұрын
Thanks
Tussi Great Ho
@techieezchannel3265
3 жыл бұрын
Thanks
Are couplers the same size for all mixers /mixer grinders?
@techieezchannel3265
3 жыл бұрын
No, it will be different for each brand mostly
Super thanks
@techieezchannel3265
2 жыл бұрын
Welcome
Thank you so much
@techieezchannel3265
3 жыл бұрын
Thanks
Thank you!
@techieezchannel3265
2 жыл бұрын
You're welcome!
How to know thread type or pressing type coupler
@SwingMotor
3 жыл бұрын
H bhai kaise
Thankyou
@techieezchannel3265
3 жыл бұрын
Thanks
Thanks
@techieezchannel3265
2 жыл бұрын
Welcome
Nice
@techieezchannel3265
3 жыл бұрын
Thanks
@rimomathew9620
3 жыл бұрын
Thank you very much
I’m having Philip mixer uska bhi aise he khulega?
@techieezchannel3265
3 жыл бұрын
Mostly it will be pressing type, thread types are not used these days
@Garry_7
3 жыл бұрын
Techieez Channel it was thread type when I took it to shop merse khula he nahi 😅
My coupler is broken on small part is left in centre how shall I remove it...
@techieezchannel3265
3 жыл бұрын
You can use plier to remove it
My coupler is completely broken on in centre it’s left little bit..
@techieezchannel3265
3 жыл бұрын
You can use plier to remove the small portion
Philipsmixer motor coupler tried to remove it but its not coming out.can you post a video please.
@techieezchannel3265
3 жыл бұрын
I Willl try
Couplers are going with in 2 days changed 3 couplers with in 10days how to over come this
@mohammednuman1650
2 жыл бұрын
Bro befor placing the jar on the grinder please check the jar blade by hand whether it is spinning freerly or not then attach the jar to the grinder this little effort keeps you happy. Hope will satisfy by the answer☺
@techieezchannel3265
2 жыл бұрын
Please verify jar fits perfectly, you can also observe if you get more noise...
Oder link please...
@techieezchannel3265
3 жыл бұрын
Which link sir
@techieezchannel3265
3 жыл бұрын
Just sample link... But you get it much cheaper rate at local store.... Preethi Coupler Mixer/Grinder Motor Coupler by Preethi www.amazon.in/dp/B00H0ELC1A/ref=cm_sw_r_em_apa_fabc_0F10K3EC9QH5YC2V6J9H
Thank you
Thank you
@techieezchannel3265
2 жыл бұрын
you'r welcome
Thank you
@techieezchannel3265
3 жыл бұрын
Thanks
Thank you
@techieezchannel3265
2 жыл бұрын
You're welcome