Pigeon 6teeth cubler 6teeth coupler jar was dameged so should it be 4teeth coupler replacement instead can you use it?pls ans me
@sumansarkar-lf1qz11 ай бұрын
Thank you ❤❤❤
@soosangeorge7986 Жыл бұрын
Thank you
@gulnazbegumgulnazbegum9660 Жыл бұрын
Thank u so much 💕
@m.sandeepchandra25442 жыл бұрын
Couplers are going with in 2 days changed 3 couplers with in 10days how to over come this
@mohammednuman16502 жыл бұрын
Bro befor placing the jar on the grinder please check the jar blade by hand whether it is spinning freerly or not then attach the jar to the grinder this little effort keeps you happy. Hope will satisfy by the answer☺
@techieezchannel32652 жыл бұрын
Please verify jar fits perfectly, you can also observe if you get more noise...
@ashar11822 жыл бұрын
Thanks for the great solution. while grinding in small jar it spilled everywhere. middle and big jar will shake and slightly rotate in groove when grinding. can you please help me in solving this problem, if you know any solutiion. My mixer is preeti eco plus and it is too noisy. Thanks in advance
@satyasanasi67882 жыл бұрын
Good sharing info. Actually its easy to open the coupler by placing the screwdriver in the hole or gap so the screwdriver will be same level with coupler and easy to open.
@SirMinardi2 жыл бұрын
Your laptop is a workbench too, nice! 😉
@IAMTHEINVINCIBLE1___2 жыл бұрын
Can you tell length of wire of this keyboard
@jentymichael2 жыл бұрын
Thank you
@techieezchannel32652 жыл бұрын
you'r welcome
@chandru1632 жыл бұрын
Superb music 💐👌👌👌use full video thanks 🙏
@techieezchannel32652 жыл бұрын
Thanks
@shebijoshi13703 жыл бұрын
Thanks for your valuable information 👍
@techieezchannel32652 жыл бұрын
So nice of you
@0x-X-x03 жыл бұрын
Thanks
@techieezchannel32652 жыл бұрын
Welcome
@DINESHKUMAR-rw5ff3 жыл бұрын
Super thanks
@techieezchannel32652 жыл бұрын
Welcome
@jamieclift44153 жыл бұрын
Very good 😊 like the music 🎶
@techieezchannel32652 жыл бұрын
Thanks ✌️
@ryanfransjak3 жыл бұрын
Philipsmixer motor coupler tried to remove it but its not coming out.can you post a video please.
@techieezchannel32653 жыл бұрын
I Willl try
@shahinamehran61183 жыл бұрын
Thank you
@techieezchannel32652 жыл бұрын
You're welcome
@chakrapanimayakuntla583 жыл бұрын
Thank you!
@techieezchannel32652 жыл бұрын
You're welcome!
@shahzad49413 жыл бұрын
Price and available islamabad
@techieezchannel32653 жыл бұрын
Pls check in Amazon
@poojachaturvedi29713 жыл бұрын
My coupler is broken on small part is left in centre how shall I remove it...
@techieezchannel32653 жыл бұрын
You can use plier to remove it
@poojachaturvedi29713 жыл бұрын
My coupler is completely broken on in centre it’s left little bit..
@techieezchannel32653 жыл бұрын
You can use plier to remove the small portion
@bikrammundchhina3 жыл бұрын
Oder link please...
@techieezchannel32653 жыл бұрын
Which link sir
@techieezchannel32653 жыл бұрын
Just sample link... But you get it much cheaper rate at local store.... Preethi Coupler Mixer/Grinder Motor Coupler by Preethi www.amazon.in/dp/B00H0ELC1A/ref=cm_sw_r_em_apa_fabc_0F10K3EC9QH5YC2V6J9H
@nikitah72223 жыл бұрын
Thanks a lot. With your help i could fix my Coupler within seconds.
@techieezchannel32653 жыл бұрын
Thank you
@nithiyarajavivekanandhan61923 жыл бұрын
Thank you very much. It was very helpful.
@techieezchannel32653 жыл бұрын
Thank you
@janetdianzingazola33433 жыл бұрын
Thanks very much it help my husband doesn't want to fix it
@techieezchannel32653 жыл бұрын
Thank you very much
@abhijeetpatil21243 жыл бұрын
After watching so many videos on where to stick the fastag, here is one video which really made sense. Thanks for this.. Keep up the good job 👍 (your daughter's narration towards the end of the video added to the beauty of the video 😃)
@techieezchannel32653 жыл бұрын
Thank u so much
@VishalYadav-vg1wi3 жыл бұрын
Sir i face a problem my mob handle head is not going straight should i applied pressure
@techieezchannel32653 жыл бұрын
Sir, No, pls check if it is defective item
@VishalYadav-vg1wi3 жыл бұрын
@@techieezchannel3265 yes thank you I also think that so I alredy applied for replacement 😀
@yanipidathala32603 жыл бұрын
Thnk u for the video , it helped me a lot
@techieezchannel32653 жыл бұрын
Thank you
@elle83883 жыл бұрын
Are couplers the same size for all mixers /mixer grinders?
@techieezchannel32653 жыл бұрын
No, it will be different for each brand mostly
@techieezchannel32653 жыл бұрын
More such music needed, pls mention in the comments section
@AnkurThakur3 жыл бұрын
Nice
@techieezchannel32653 жыл бұрын
Thanks
@rimomathew96203 жыл бұрын
Thank you very much
@Garry_73 жыл бұрын
I’m having Philip mixer uska bhi aise he khulega?
@techieezchannel32653 жыл бұрын
Mostly it will be pressing type, thread types are not used these days
@Garry_73 жыл бұрын
Techieez Channel it was thread type when I took it to shop merse khula he nahi 😅
@sahasrakandimalla16613 жыл бұрын
What about quality bro?
@techieezchannel32653 жыл бұрын
It is good for the price range
@pradeeprepal50914 жыл бұрын
you bought it for what price
@techieezchannel32654 жыл бұрын
Rs 1200
@kathilantodu39643 жыл бұрын
@@techieezchannel3265 no it is 899 only now
@mrmalabari33913 жыл бұрын
kathi lantodu in which sight
@mrmalabari33913 жыл бұрын
Techieez Channel sure?
@kathilantodu39643 жыл бұрын
@@mrmalabari3391 in more megastore
@snigSamArt21424 жыл бұрын
Thank you
@techieezchannel32653 жыл бұрын
Thanks
@MOBILEPHOTOGRAPHYSTUDIO4 жыл бұрын
Tanx bro..100% working👍
@techieezchannel32652 жыл бұрын
Great , thanks
@druvaj4 жыл бұрын
Thank you so much
@techieezchannel32653 жыл бұрын
Thanks
@muthupaul86094 жыл бұрын
How to know thread type or pressing type coupler
@SwingMotor3 жыл бұрын
H bhai kaise
@majharalam42484 жыл бұрын
Tussi Great Ho
@techieezchannel32653 жыл бұрын
Thanks
@majharalam42484 жыл бұрын
nice
@TheSunithanaidu4 жыл бұрын
Thank you so much. Great help!
@techieezchannel32653 жыл бұрын
Thankx
@beenaphilip39854 жыл бұрын
Thank you
@lokeshwaranparandhaman5674 жыл бұрын
Was wondering if the bush was a screw type but this video was help full to know it was just the push type. But there is better way to pull the broken bush out rather trying to tweaking from the top. There is a open slit in through where we can get the screw driver to the bottom of the bush in a straight angle. Makes the job easier.
@manikalyani4 жыл бұрын
Thankyou
@techieezchannel32653 жыл бұрын
Thanks
@jawidnazir4 жыл бұрын
Thank you very useful
@techieezchannel32653 жыл бұрын
Thanks
@shweta82024 жыл бұрын
Why does the bulb blinks continuously??Is there any adjustment to be made in colour flash mode to stop this blinking?
@leelavathi11194 жыл бұрын
Recently I bought a Wipro Smart bulb. Connected to Google Home Mini. It works for the commands, but the problem is even after giving " turn off " command it turns off but flickers often. What could be the problem?. Its happening in all the different holders in the house. Electrician says no problem with connections & wiring .
@techieezchannel32654 жыл бұрын
Not sure on the issue, but you can redo the setup and try once again.
@bsebl0075 жыл бұрын
I purchased two Wipro Garnet 9 W smart Bulbs but I cannot use it because I don't have wi-fi router at home also don't have two smart phone to create wi-fi network. I called Toll free No: 1800-425-1969 customer care and they said it works only with Wi-fi for that I need wi-fi router or two smart phone. I also asked them what is that the AP mode, after kept me on hold I got answer they don't have any technical information about that. How bad support team of Wipro (since it is technical company).
Пікірлер
Where can i buy this?
Good video, it saved my time and money
Pigeon 6teeth cubler 6teeth coupler jar was dameged so should it be 4teeth coupler replacement instead can you use it?pls ans me
Thank you ❤❤❤
Thank you
Thank u so much 💕
Couplers are going with in 2 days changed 3 couplers with in 10days how to over come this
Bro befor placing the jar on the grinder please check the jar blade by hand whether it is spinning freerly or not then attach the jar to the grinder this little effort keeps you happy. Hope will satisfy by the answer☺
Please verify jar fits perfectly, you can also observe if you get more noise...
Thanks for the great solution. while grinding in small jar it spilled everywhere. middle and big jar will shake and slightly rotate in groove when grinding. can you please help me in solving this problem, if you know any solutiion. My mixer is preeti eco plus and it is too noisy. Thanks in advance
Good sharing info. Actually its easy to open the coupler by placing the screwdriver in the hole or gap so the screwdriver will be same level with coupler and easy to open.
Your laptop is a workbench too, nice! 😉
Can you tell length of wire of this keyboard
Thank you
you'r welcome
Superb music 💐👌👌👌use full video thanks 🙏
Thanks
Thanks for your valuable information 👍
So nice of you
Thanks
Welcome
Super thanks
Welcome
Very good 😊 like the music 🎶
Thanks ✌️
Philipsmixer motor coupler tried to remove it but its not coming out.can you post a video please.
I Willl try
Thank you
You're welcome
Thank you!
You're welcome!
Price and available islamabad
Pls check in Amazon
My coupler is broken on small part is left in centre how shall I remove it...
You can use plier to remove it
My coupler is completely broken on in centre it’s left little bit..
You can use plier to remove the small portion
Oder link please...
Which link sir
Just sample link... But you get it much cheaper rate at local store.... Preethi Coupler Mixer/Grinder Motor Coupler by Preethi www.amazon.in/dp/B00H0ELC1A/ref=cm_sw_r_em_apa_fabc_0F10K3EC9QH5YC2V6J9H
Thanks a lot. With your help i could fix my Coupler within seconds.
Thank you
Thank you very much. It was very helpful.
Thank you
Thanks very much it help my husband doesn't want to fix it
Thank you very much
After watching so many videos on where to stick the fastag, here is one video which really made sense. Thanks for this.. Keep up the good job 👍 (your daughter's narration towards the end of the video added to the beauty of the video 😃)
Thank u so much
Sir i face a problem my mob handle head is not going straight should i applied pressure
Sir, No, pls check if it is defective item
@@techieezchannel3265 yes thank you I also think that so I alredy applied for replacement 😀
Thnk u for the video , it helped me a lot
Thank you
Are couplers the same size for all mixers /mixer grinders?
No, it will be different for each brand mostly
More such music needed, pls mention in the comments section
Nice
Thanks
Thank you very much
I’m having Philip mixer uska bhi aise he khulega?
Mostly it will be pressing type, thread types are not used these days
Techieez Channel it was thread type when I took it to shop merse khula he nahi 😅
What about quality bro?
It is good for the price range
you bought it for what price
Rs 1200
@@techieezchannel3265 no it is 899 only now
kathi lantodu in which sight
Techieez Channel sure?
@@mrmalabari3391 in more megastore
Thank you
Thanks
Tanx bro..100% working👍
Great , thanks
Thank you so much
Thanks
How to know thread type or pressing type coupler
H bhai kaise
Tussi Great Ho
Thanks
nice
Thank you so much. Great help!
Thankx
Thank you
Was wondering if the bush was a screw type but this video was help full to know it was just the push type. But there is better way to pull the broken bush out rather trying to tweaking from the top. There is a open slit in through where we can get the screw driver to the bottom of the bush in a straight angle. Makes the job easier.
Thankyou
Thanks
Thank you very useful
Thanks
Why does the bulb blinks continuously??Is there any adjustment to be made in colour flash mode to stop this blinking?
Recently I bought a Wipro Smart bulb. Connected to Google Home Mini. It works for the commands, but the problem is even after giving " turn off " command it turns off but flickers often. What could be the problem?. Its happening in all the different holders in the house. Electrician says no problem with connections & wiring .
Not sure on the issue, but you can redo the setup and try once again.
I purchased two Wipro Garnet 9 W smart Bulbs but I cannot use it because I don't have wi-fi router at home also don't have two smart phone to create wi-fi network. I called Toll free No: 1800-425-1969 customer care and they said it works only with Wi-fi for that I need wi-fi router or two smart phone. I also asked them what is that the AP mode, after kept me on hold I got answer they don't have any technical information about that. How bad support team of Wipro (since it is technical company).