Wow this channel seems awesome. I’ve learned so much since I’ve moved up to the north woods from this guy!

Great video, thank you.

They make roller helixes for the secondary that work so much better than stock. I ran one on my vmax4 and it woke that thing up

You gotta adjust the belt deflection too your belt is really loose

Just wondering do you still have the same top speed with the higher degree setting. I understand the higher degree is for a better launch. Thank you 👍

@Whitestrash

5 ай бұрын

Never had her topped out in either setting, so I couldn't tell ya..definitely impoved acceleration tho!

Big jump from stock 40 to 70. Did you slowly go up? How much of a difference is there

@Whitestrash

Жыл бұрын

I just went right to 70. It runs about 500rpm higher than stock at about 40mph on a flat trail. I put it back to stock when trail riding with slow people so it's not screaming all the time.

I have a 96 vmax 500 with a sticky primary, any chance you have advice on how to service or rebuild one ?

@Whitestrash

5 ай бұрын

I haven't had the primary all the way apart on a Yamaha. You may need to take the spider off to get to the buttons, that would require special tools in most cases.

Assuming similar concept for the 94 vmax's?

@Whitestrash

4 ай бұрын

Probably

What does increasing the tension do? My Yamaha takes a lot of rpm’s to get going

@Whitestrash

Жыл бұрын

Increasing the tension in the secondary makes it backshift harder. Also makes it harder for the secondary to open, which is like staying in a lower gear longer. As far as it taking a lot of rpm to get moving that's in your primary clutch. It should engage around 4000 rpm.

@jambotis

Жыл бұрын

@@Whitestrash thanks so much. I have a 99 venture 500 and it revs really high when riding. Like 6500 rpm at 45-50 mph. If you give it gas it goes faster but it’s like it’s in a really low gear almost. You think I should close up the gap on the secondary clutch? The belt sits flush does not protrude over the edge.

@Whitestrash

Жыл бұрын

It's normal on these sleds for the belt to sit flush or slightly below the secondary. You could see where your secondary is set (like in the video) maybe someone messed with it and it's way off??

@Whitestrash

Жыл бұрын

Also, it should rev to around 8000rpm at full throttle, winding out.

@jjwalker2011

Жыл бұрын

Any suggestions for clutch engagement @ 6k rpm? I've replaced my primary & it's still an issue. Any thoughts appreciated. It has to be an issue with my secondary right?

How many shims are on the secondary bolt 2 or 3?

@Whitestrash

6 ай бұрын

There's a bunch. It varies from sled to sled, based on clutch alignment.

@HunterMckay7

6 ай бұрын

@@Whitestrash should there always be a shim on the shaft before the secondary?

@Whitestrash

6 ай бұрын

@@HunterMckay7 probably. You don't want the bare clutch rotating against anything. The washers align the clutch and offer protection to some degree.

Just trying to understand what you mean by backshift harder. How do we set belt tension? New to the sled world and just trying to educate myself. Thanks for any help you can provide. Paul

@Whitestrash

Жыл бұрын

I'm no expert on the subject, but backshifting is when the secondary clutch closes back up on deceleration. It also keeps it in a "lower gear"for longer the tighter the spring is. Belt tension should be close as long as your clutch center to center measurement is in spec. You have a little fine tuning adjustment from there (on yamaha) by adding or removing shims on the secondary. There are tons of vids on that procedure. Just look for "yamaha snowmobile belt deflection" and you'll find it.

Where is the zerk itting to grease it.

@Whitestrash

8 ай бұрын

There isn't one.