Great vid, I have done clutches for a decade and still forget every year, this was a great reminder!!!

Great video, after watching I realized I never lined up my primary cover with the spider after cleaning. Fixed it thanks to you pointing it out in this video.

@Totallyamaha

2 жыл бұрын

Your welcome!!

Nice Tech Vid. This answered a lot of my questions. Thanks.

You just held onto the clutch while removing spring ? I thought the tension would have pushed crazy hard and went flying ? You made this look very easy.

Great video guys appreciate it.

@Totallyamaha

9 жыл бұрын

Thank you!!

Great Video! Thanks!

Do what changes were noticable with this clutch kit.

Awesome thanks for the help

Great video

Great job on Video... :)

Excellent video. When replacing stock clutch parts would you recommend aftermarket parts or OEM? Not performance just stock. For a 2009 Vector with 13,000 km. Thanks Mark

@Totallyamaha

5 жыл бұрын

Mark Bow oem if you don’t have a clutch kit.

great vid but you said nothing about what exactly the changes would will do for tbe performance of the sled? what exactly does it improve?

@Totallyamaha

7 жыл бұрын

Great mid-range power as well as a little on top end. About 2-3 sled length over stock.

@darrrenbetker4266

7 жыл бұрын

How much in Canadian is this clutch kit worth? My sled is a minty low kn 06 apex gt. Its updated but otherwise stock other then a swis cheese muffler mod so what other mods would i need to help this kit work

@Totallyamaha

6 жыл бұрын

Contact Ulmer Racing for current pricing.

@Totallyamaha

6 жыл бұрын

You can also open up the air box lid with some cold air vents.

Good video I am doing same thing to my nytro. Shouldn't you be using Loctite and maybe some lube on the pins?

@Totallyamaha

5 жыл бұрын

MrSprintcat. No and no. What makes you think that?

@MrSprintcat

5 жыл бұрын

I just thought it would make the weights go in and out a lot easier

@Totallyamaha

5 жыл бұрын

MrSprintcat I have seen graphite used but it’s best to leave them dry with the material used in the bushings. If torqued properly never use loc-tite

@MrSprintcat

5 жыл бұрын

Okay thank you will do .

I already posted the gains. 2-3 sled lengths. Bottom and mid range acceleration.

@stephenrand5033

Жыл бұрын

Which video is the gains?

@Totallyamaha

Жыл бұрын

@@stephenrand5033 there is none.

Do any of the pins, rollers, shafts or any other parts in these clutches get grease? Or is it a totally dry assembly? Thanks.

@Totallyamaha

Жыл бұрын

Totally dry assembly.

@luckygoose844

Жыл бұрын

I have one more question if I may. I have a 2018 VK pro 2 and my clutch is trashed. I was thinking of replacing it with a powerblock 80 . Is this a good idea? Is it a good clutch? Is it quieter? Is it better? Thanx for your input!! Cheers.

@Totallyamaha

Жыл бұрын

@@luckygoose844 I am not sure how good those are. The clutch is not what makes noise on that machine. It’s the stub shaft counter weight. It will rattle less but will still rattle. I’d just toss on another Yamaha clutch or you could contact Thunder Products clutching and the may be able to rebuild that.

where can I find the stock spring specifications for the clutch springs? Yamaha nitro fx 09

@Totallyamaha

6 жыл бұрын

totallyamaha.com/snowmobiles/AAATuning%20Chart/Specs.htm

@Totallyamaha

6 жыл бұрын

It would be better if you register and post these questions on the forum on Totallyamaha.net

comment on fait pour demancher un yam-charge sur un apex

I have a sr Viper and wondering what clutch kit would get me the best ski lift. I want to be able to do better wheelies.

@Totallyamaha

4 жыл бұрын

What sled do you have? LTX or XTX? Any boost?

@ThrottleDownTV

4 жыл бұрын

@@Totallyamaha xtx

@Totallyamaha

4 жыл бұрын

@@ThrottleDownTV Stiffer center spring on rear suspension will help or contact Thunder Products Clutching

@ThrottleDownTV

4 жыл бұрын

@@Totallyamaha is thunder products a lower engagement

@Totallyamaha

4 жыл бұрын

MOTO GUYS they can give you anything you want.

Hey @totallyamaha is this going to be the exact same install as on a 19' Sidewinder?

@Totallyamaha

4 жыл бұрын

Yes, other then the Sidewinder has a roller secondary not a button.

@Shift891

4 жыл бұрын

@@Totallyamaha not exactly sure what you mean by roller secondary? Is this going to change the install procedure or anything specific i need to watch for? Thanks

@Totallyamaha

4 жыл бұрын

@@Shift891 no you should be fine. You can always contact me if you get stuck.

@Shift891

4 жыл бұрын

@@Totallyamaha beautiful your a life saver haha thanks mann. ill contact you if needed!

thy didnt change the clutching system .my sx 700 has same clutching .

where do i get the clutch kit ?

@idtd2001

7 жыл бұрын

Have you noticed different between stock and aftermarket one.

Contact Ulmer Racing....google search them. Cant post links in here.

You should mark a line on the cover and Spider so put everything back for balance of the Clutch parts

@Totallyamaha

7 жыл бұрын

No need to , they have an X stamped into all mating parts to keep them aligned for balance.

Where to buy pine tools?

@Totallyamaha

7 ай бұрын

Pine tools?

Ulmer racing is only 15 miles from me :D

I need a clutch kit for my phazer it hits rev limiter

@Totallyamaha

6 жыл бұрын

You could add more tip weight first.. 4 stroke or 2stroke ?

@mainebassin8176

6 жыл бұрын

Totallyamaha 4 stroke it has a exhaust and a fuel programmer it's a mtx so I think the promblem is that it is clutched for high elevations

@Totallyamaha

6 жыл бұрын

Yes you will need a clutch kit with a fuel programmer. You can try to add some weight to the tip but I think it will work way better all the way around if you do the kit. Try Ulmer Racing.

@mainebassin8176

6 жыл бұрын

Totallyamaha what kit should I get

Can you tell me if these machines . The clutch is pressed over the spine or does it just freely slide to the seat.

@Totallyamaha

4 ай бұрын

I am not following you. Please clarify. Primary clutch or secondary clutch? Maybe go to our website, register and ask questions.

@dustinfeaver215

4 ай бұрын

@Totallyamaha on the secondary clutch. The clutch sits on the spline which you will have a spacer behind. But the clutch is not going flush to the seat. There is about an 1/4 " remaining it has to go in. But will not move.

@Totallyamaha

4 ай бұрын

@@dustinfeaver215 if it’s not on splines correctly it won’t go on all the way. You have to mesh the splines.