You can also check the bin switch,with the board amber and green light.and you can use a drier plastic caps to plug the float boot,to remove and clean,i always leave one at the machine LOL.

@IceMachine411

6 ай бұрын

Great tips! Thank you 🙏

@sherwinalvarez7365

6 ай бұрын

Great tips bro. Thanx.

Great videos. Not many people on KZread simplifing IM troubleshooting.

@IceMachine411

6 ай бұрын

Thanks. I’m trying to share what I can. I’m also learning a lot in the process.

Great Video. Good job and Nice work. Thank you for sharing

@IceMachine411

6 ай бұрын

Thank you!

Excellent video !!!!! 👍👍 you are a Hoshizaki GURU

@IceMachine411

6 ай бұрын

Hardly. lol

You make it look easy.

@IceMachine411

6 ай бұрын

All day, every day. Nothing but ice.

Thank you for the video.

@IceMachine411

6 ай бұрын

You’re welcome.

Nice job

@IceMachine411

6 ай бұрын

💪

great video, great job on that repair. Did you show how to make that "adjustment" or did I just miss it?

@IceMachine411

6 ай бұрын

I didn’t. I raised the float switch housing up. Loosened two screws and slid it up.

You should put the model number of the units you’re working on for search purposes. I was looking for km-250 tutorial to listen to

@IceMachine411

5 ай бұрын

I will try to make that happen going forward.

👍👍👍

@IceMachine411

6 ай бұрын

🫡

Hello. Just want to ask how to adjust the thickness of Hoshizaki Im-cne45.. I want the machine to release Ice faster even tho its not going to be thick..

@IceMachine411

3 ай бұрын

I’m not sure exactly. You may need to locate the manual or call hoshizaki tech support. Some have float housings, some have floats in the water tank that are not adjustable. I’m not sure what your machine has or how to adjust it.

whats the best way to empty the water reservoir, I don't work on ice machines very much, I do vrf heat recovery systems and builds, but when we are on call service some restaurant chains and man not knowing these units sure sucks i pulled that float one time and made a hell of a mess. OOPS

@IceMachine411

6 ай бұрын

lol! Did the same thing once. Some machines have plugs and some have a switch you can flip to make the machine drain itself. They’re all slightly different.

@lickitysplit2413

5 ай бұрын

Pull diaphragm out of purge valve, turn on pump, pinch-off water feed tube to spray tubes, pump out is quick.

Clean pump section. How old is the machine?

@IceMachine411

6 ай бұрын

Not that old. Less than a year I think.

@sherwinalvarez7365

6 ай бұрын

Yeah spray tubes were very clean. Not used to seeing that.

This machines make most of the ice at the end of freeze cycle,to short of a freeze might be low production,2 cents.

@IceMachine411

6 ай бұрын

Hmmm…. You make a valid point. Maybe instead of a 20 minute freeze I could have tried for 25 minutes.

@MariosACandRefrigeration

6 ай бұрын

it calls for 28 to 30 min.3 1/2 harvest +or-@@IceMachine411

@sherwinalvarez7365

6 ай бұрын

Yeah, i have to start using my tech specs book to see the times. Also, Hoshizaki needs to make markings at the adjustment . I like to go halfway between the hole on the top.

❄️💪👍🇺🇸

@IceMachine411

6 ай бұрын

💪🛠️