Goodman Furnace fault LED 3 flashes - Air Pressure Switch stuck open
Жүктеу.....
Пікірлер: 89
@therealmaccoy251
Exactly my problem! Straighten out a paper clip and removed the blockage without removing the motor. Furnace fired right up! So glad thankful to have heat again! Thanks Nagen!!!
@Rustytales
Thank you very much!
@themexicanstaringfrogofsou5268 Жыл бұрын
I'm getting a code 2 on my goodman furnace. It says to check venter end switch. Is that the switch located on the inducer motor? Do I need to replace to inducer motor? Mine doesn't seem to have a pressure switch or hose coming out the inducer motor plumbing
@aaronrodden8121 Жыл бұрын
Fyi use a small gun cleaning brush attached to a drill....Thoroughly cleans it as the gunk will build back up soon if not done properly. Use a quick drying lube (dry lubricant) to help seal the corrosion as well as prevent more gunk build up due to corrosion.
@chadvaughn35595 жыл бұрын
Thank you! Saved a service call. Removed motor, used a paper clip to run in and out of the hole and fixed it!
@spirenoir Жыл бұрын
Had replaced the control board, no luck...Blew compressed air into the nipple where the hose connects. Fired up instantly. Thanks for the video.
@IIINEMESESII4 жыл бұрын
Thanks man all I had to do was take off the little grey hose and re seat it. It's working now just saved me so much money. My gma keeps paying out the ass to fix this damn furnace. Happens every year. Now I know what they are doing an why it only takes them a few minutes to get it working. Looks like I need a fresh hose mine is split on one end. Doesn't fit right as should I assume. Wayyy cheaper to get myself new hose an replace myself instead of calling the same damn company to rip us off. Thank you
@captaindelaigle7531 Жыл бұрын
Thank you! Spent two hours hinder my house and all it ended up being some trash in that nipple! Didn’t have to take it all off just the hose. Very helpful and saved a good bit of money! Thank you!
@gregorycasey22713 жыл бұрын
Thanks Nagen , that small tube was full of water and dirt on mine , gave it a quick clean and it fired right up .
@GregInATX4 жыл бұрын
Thank you So much for this video. My induction motor valve was clogged as well. I cleaned it out with a drywall nail. Thanks again for posting this video. Its was 29 outside today. I was placing a service call tomorrow just thought to give it a try and found this video. I watched about 8 or 9 but none covered this issue.
@Quejuans Жыл бұрын
Saved me some money. Somehow a baby bat got lodged in the motor and was blocking everything up. Clean it out and furnaces fired right back up
@nickgoesvestmode5 жыл бұрын
This helped me too! Thank you!! I had an HVAC guy scheduled Monday and now I can cancel! Thanks!!!
@dursty32262 жыл бұрын
Bless you!
@JavierIncRealty2 жыл бұрын
TOTALLY LEGIT!!!!!! Do it and save yourself the money! Not lighting??? This is probably why! Thanks DUDE!
@bigricyomamie11823 жыл бұрын
Your vids saved me as lot of money thank u may god be with u
@sabbasdsouza5 жыл бұрын
Thank you so much Nagen for sharing this. I had three flashing LED light fault code and did the same thing. Coldest night of the year and the furnace is working again. That was a real helping video.
@kylefromkansas
Thanks for this video it fixed my problem. I was able to poke it while it was still on the furnace fortunately just took off the hose.
@cjchand4 жыл бұрын
Just another note of thanks. I was able to use your info to fix my furnace... without even removing the blower. Thanks again!
@MrTaherikbal2 жыл бұрын
Thanks, it helped and solved my issue too. You don't need to take off motor to clean clogged nozzle just run hair pin or copper wire thru it. However opening the motor let you see clog and satisfies you.
@shawndavis92762 жыл бұрын
Thanks dude! I ended up having to take the hose off from the motor to the switch and cleaning that out I just blew on it really hard and a bunch of dust came out you’re the man
Пікірлер: 89
Exactly my problem! Straighten out a paper clip and removed the blockage without removing the motor. Furnace fired right up! So glad thankful to have heat again! Thanks Nagen!!!
Thank you very much!
I'm getting a code 2 on my goodman furnace. It says to check venter end switch. Is that the switch located on the inducer motor? Do I need to replace to inducer motor? Mine doesn't seem to have a pressure switch or hose coming out the inducer motor plumbing
Fyi use a small gun cleaning brush attached to a drill....Thoroughly cleans it as the gunk will build back up soon if not done properly. Use a quick drying lube (dry lubricant) to help seal the corrosion as well as prevent more gunk build up due to corrosion.
Thank you! Saved a service call. Removed motor, used a paper clip to run in and out of the hole and fixed it!
Had replaced the control board, no luck...Blew compressed air into the nipple where the hose connects. Fired up instantly. Thanks for the video.
Thanks man all I had to do was take off the little grey hose and re seat it. It's working now just saved me so much money. My gma keeps paying out the ass to fix this damn furnace. Happens every year. Now I know what they are doing an why it only takes them a few minutes to get it working. Looks like I need a fresh hose mine is split on one end. Doesn't fit right as should I assume. Wayyy cheaper to get myself new hose an replace myself instead of calling the same damn company to rip us off. Thank you
Thank you! Spent two hours hinder my house and all it ended up being some trash in that nipple! Didn’t have to take it all off just the hose. Very helpful and saved a good bit of money! Thank you!
Thanks Nagen , that small tube was full of water and dirt on mine , gave it a quick clean and it fired right up .
Thank you So much for this video. My induction motor valve was clogged as well. I cleaned it out with a drywall nail. Thanks again for posting this video. Its was 29 outside today. I was placing a service call tomorrow just thought to give it a try and found this video. I watched about 8 or 9 but none covered this issue.
Saved me some money. Somehow a baby bat got lodged in the motor and was blocking everything up. Clean it out and furnaces fired right back up
This helped me too! Thank you!! I had an HVAC guy scheduled Monday and now I can cancel! Thanks!!!
Bless you!
TOTALLY LEGIT!!!!!! Do it and save yourself the money! Not lighting??? This is probably why! Thanks DUDE!
Your vids saved me as lot of money thank u may god be with u
Thank you so much Nagen for sharing this. I had three flashing LED light fault code and did the same thing. Coldest night of the year and the furnace is working again. That was a real helping video.
Thanks for this video it fixed my problem. I was able to poke it while it was still on the furnace fortunately just took off the hose.
Just another note of thanks. I was able to use your info to fix my furnace... without even removing the blower. Thanks again!
Thanks, it helped and solved my issue too. You don't need to take off motor to clean clogged nozzle just run hair pin or copper wire thru it. However opening the motor let you see clog and satisfies you.
Thanks dude! I ended up having to take the hose off from the motor to the switch and cleaning that out I just blew on it really hard and a bunch of dust came out you’re the man