Thanks for this video it fixed my problem. I was able to poke it while it was still on the furnace fortunately just took off the hose.
@HungNguyen-sb1yu5 ай бұрын
I have a comfort maker furnace. Where can I find the tiny hole? Thank you.
@Rustytales6 ай бұрын
Thank you very much! I checked everything and all the parts were working, but the igniter was not receiving 120 volts. Then I found your video and cleaned this thin tube, everything immediately worked as it should! What are the engineers thinking who come up with this junk? It turns out that due to a clogged hole with a diameter of just over a millimeter, a family can freeze in the winter without heating. Junk makers, not engineers. Thank you again for your video!
@7oriole78 ай бұрын
Thankyou much
@therealmaccoy2519 ай бұрын
Exactly my problem! Straighten out a paper clip and removed the blockage without removing the motor. Furnace fired right up! So glad thankful to have heat again! Thanks Nagen!!!
@ejflesher10 ай бұрын
This fixed my issue. Thank you so much
@spirenoir Жыл бұрын
Had replaced the control board, no luck...Blew compressed air into the nipple where the hose connects. Fired up instantly. Thanks for the video.
@fernandonumba45.16 Жыл бұрын
You are a goat 🐐 thank you for the help
@jjhatnm Жыл бұрын
My lights flash red three times just like that, but their is NO noise from the motors/fans like you hear. Mine is silent. What does that mean?
@eddymumford4086 Жыл бұрын
Does anyone's Goodman furnace ever flash a number 2 when running only when it's running 🤔 mine dose but I never see anyone else's I watched a lot of videos... maybe mine is the only one 😁
@sonGOKU._. Жыл бұрын
This error code is the worst 😢
@bradleycole5079 Жыл бұрын
You literally just saved me and my family hundreds!!! And on Christmas Night!! Thank you very much!!!
@aaronrodden8121 Жыл бұрын
Fyi use a small gun cleaning brush attached to a drill....Thoroughly cleans it as the gunk will build back up soon if not done properly. Use a quick drying lube (dry lubricant) to help seal the corrosion as well as prevent more gunk build up due to corrosion.
@aaronrodden8121 Жыл бұрын
This worked for me but after a year, the inducer motor started not coming on until I tapped the control board a few times with power off then turning power back on. I'm working on that issue as we speak.
@AdamEisan Жыл бұрын
You rock! Just saved me a ton on a service call. Much appreciated my friend!
@sharonmanetta7685 Жыл бұрын
Where did you find that switch
@themexicanstaringfrogofsou5268 Жыл бұрын
I'm getting a code 2 on my goodman furnace. It says to check venter end switch. Is that the switch located on the inducer motor? Do I need to replace to inducer motor? Mine doesn't seem to have a pressure switch or hose coming out the inducer motor plumbing
@Tony-tt5mn Жыл бұрын
You're the man! After trying to clear it with compressed air(no luck) I cleared it with a guitar string without taking the motor off. Hope this saves someone some time!
@carterbersano3475 Жыл бұрын
THANK YOU! This was exactly the problem!
@lel70schildofthemosthigh71 Жыл бұрын
Thanks soooo much it helped me out as well !!! Saved me the service call !!!!
@captaindelaigle7531 Жыл бұрын
Thank you! Spent two hours hinder my house and all it ended up being some trash in that nipple! Didn’t have to take it all off just the hose. Very helpful and saved a good bit of money! Thank you!
@Quejuans Жыл бұрын
Saved me some money. Somehow a baby bat got lodged in the motor and was blocking everything up. Clean it out and furnaces fired right back up
@naturallyj3995 Жыл бұрын
How did you get the front panel off
@c_2017 Жыл бұрын
Three small screw underneath the panel. Unscrew them and the panel literally comes right off.
@thetruckandi2 жыл бұрын
7 Extremely helpful!
@woodlandxwarrior2 жыл бұрын
Thanks brother. I did not confirm if this is the issue just yet, but I've already kinds looked at the system, and are having the same issues. Error code 3: PS switch stuck open. I'll check it now.
@jefferycoles48132 жыл бұрын
Thank you so much. Greatly appreciated
@HenryBloggit2 жыл бұрын
Can’t hear a word you say
@moecapitolnetwork29162 жыл бұрын
In my case it was a clogged filter
@blackpeterose2 жыл бұрын
Nice job Sir! You are spot on with this repair. 👏 I
@kevinswaney58752 жыл бұрын
Hi, I was hoping you could give me some advice. My parents had a new Amana furnace 6 roller (model AMES801205DX installed. Unfortunately they continued to have problems with it. The seller admitted they installed too big of a furnace for their house and replaced it with a Goodman 3 roller (model AMES800604BXAA). They did not receive any refund for the price difference. My dad has dementia and my mom has Parkinson. I think the company took advantage of them, but I can't find the prices for the furnaces. Any feedback you could provide would be greatly appreciated. Thanks, Kevin
@shawndavis92762 жыл бұрын
Thanks dude! I ended up having to take the hose off from the motor to the switch and cleaning that out I just blew on it really hard and a bunch of dust came out you’re the man
@JavierIncRealty2 жыл бұрын
TOTALLY LEGIT!!!!!! Do it and save yourself the money! Not lighting??? This is probably why! Thanks DUDE!
@MrTaherikbal2 жыл бұрын
Thanks, it helped and solved my issue too. You don't need to take off motor to clean clogged nozzle just run hair pin or copper wire thru it. However opening the motor let you see clog and satisfies you.
@wmoore02112 жыл бұрын
Thank you! This was exactly the problem! Running smooth again!
@dursty32262 жыл бұрын
Bless you! all i had to do was clean out that little tube on the motor. thank you for sharing your knowledge and expertise!
@d.ppineda44872 жыл бұрын
Thank you for your help
@frankborja14032 жыл бұрын
Thank you very much thanks to your video today I was able to fix my furnace just as you stated in this video
@kennethdandurand34722 жыл бұрын
Turn your voice up..... you are whispering.
@rocbrar3 жыл бұрын
Thank you!
@elprimojales57043 жыл бұрын
TY!!!
@mikestein10243 жыл бұрын
God bless you sir !!!!
@513goldybaby3 жыл бұрын
Thanks 👍 it's 23 degrees out side and feel like -10 inside watch this video and now it feels like 76 on the beach ⛱️. Thank you A++
@bigricyomamie11823 жыл бұрын
Your vids saved me as lot of money thank u may god be with u
@larrykornstadt12413 жыл бұрын
Thank you so much, wish I could buy you a beer, appreciate your sharing this. Merry Christmas my friend
@Triceptor783 жыл бұрын
Thank you!!!
@mr.k27443 жыл бұрын
Awesome man! I had the same exact problem and just fixed it today! Thank You! Tomr is 30* in NYC 🥶
@Death_Row_Anglers3 жыл бұрын
PROBLEM SOLVED! Thank you! I had the same problem that you did. I just subscribed to your channel. Thanks again 👌🏾
@gregorycasey22713 жыл бұрын
Thanks Nagen , that small tube was full of water and dirt on mine , gave it a quick clean and it fired right up .
@carlossantos2525254 жыл бұрын
Man you save me $ tnks for the video I did just that and it works fine now kids are happy and wife is no bothering any more 😃
@blueg30274 жыл бұрын
Not sure why you had to pull the inducer lol just check your pressures with your manometer. Waste of time and money for your customer
@Nagenmaha4 жыл бұрын
Jordan G I didn’t have manometer, just to let you know that was my first time opening HVAC unit
Пікірлер
Thanks for this video it fixed my problem. I was able to poke it while it was still on the furnace fortunately just took off the hose.
I have a comfort maker furnace. Where can I find the tiny hole? Thank you.
Thank you very much! I checked everything and all the parts were working, but the igniter was not receiving 120 volts. Then I found your video and cleaned this thin tube, everything immediately worked as it should! What are the engineers thinking who come up with this junk? It turns out that due to a clogged hole with a diameter of just over a millimeter, a family can freeze in the winter without heating. Junk makers, not engineers. Thank you again for your video!
Thankyou much
Exactly my problem! Straighten out a paper clip and removed the blockage without removing the motor. Furnace fired right up! So glad thankful to have heat again! Thanks Nagen!!!
This fixed my issue. Thank you so much
Had replaced the control board, no luck...Blew compressed air into the nipple where the hose connects. Fired up instantly. Thanks for the video.
You are a goat 🐐 thank you for the help
My lights flash red three times just like that, but their is NO noise from the motors/fans like you hear. Mine is silent. What does that mean?
Does anyone's Goodman furnace ever flash a number 2 when running only when it's running 🤔 mine dose but I never see anyone else's I watched a lot of videos... maybe mine is the only one 😁
This error code is the worst 😢
You literally just saved me and my family hundreds!!! And on Christmas Night!! Thank you very much!!!
Fyi use a small gun cleaning brush attached to a drill....Thoroughly cleans it as the gunk will build back up soon if not done properly. Use a quick drying lube (dry lubricant) to help seal the corrosion as well as prevent more gunk build up due to corrosion.
This worked for me but after a year, the inducer motor started not coming on until I tapped the control board a few times with power off then turning power back on. I'm working on that issue as we speak.
You rock! Just saved me a ton on a service call. Much appreciated my friend!
Where did you find that switch
I'm getting a code 2 on my goodman furnace. It says to check venter end switch. Is that the switch located on the inducer motor? Do I need to replace to inducer motor? Mine doesn't seem to have a pressure switch or hose coming out the inducer motor plumbing
You're the man! After trying to clear it with compressed air(no luck) I cleared it with a guitar string without taking the motor off. Hope this saves someone some time!
THANK YOU! This was exactly the problem!
Thanks soooo much it helped me out as well !!! Saved me the service call !!!!
Thank you! Spent two hours hinder my house and all it ended up being some trash in that nipple! Didn’t have to take it all off just the hose. Very helpful and saved a good bit of money! Thank you!
Saved me some money. Somehow a baby bat got lodged in the motor and was blocking everything up. Clean it out and furnaces fired right back up
How did you get the front panel off
Three small screw underneath the panel. Unscrew them and the panel literally comes right off.
7 Extremely helpful!
Thanks brother. I did not confirm if this is the issue just yet, but I've already kinds looked at the system, and are having the same issues. Error code 3: PS switch stuck open. I'll check it now.
Thank you so much. Greatly appreciated
Can’t hear a word you say
In my case it was a clogged filter
Nice job Sir! You are spot on with this repair. 👏 I
Hi, I was hoping you could give me some advice. My parents had a new Amana furnace 6 roller (model AMES801205DX installed. Unfortunately they continued to have problems with it. The seller admitted they installed too big of a furnace for their house and replaced it with a Goodman 3 roller (model AMES800604BXAA). They did not receive any refund for the price difference. My dad has dementia and my mom has Parkinson. I think the company took advantage of them, but I can't find the prices for the furnaces. Any feedback you could provide would be greatly appreciated. Thanks, Kevin
Thanks dude! I ended up having to take the hose off from the motor to the switch and cleaning that out I just blew on it really hard and a bunch of dust came out you’re the man
TOTALLY LEGIT!!!!!! Do it and save yourself the money! Not lighting??? This is probably why! Thanks DUDE!
Thanks, it helped and solved my issue too. You don't need to take off motor to clean clogged nozzle just run hair pin or copper wire thru it. However opening the motor let you see clog and satisfies you.
Thank you! This was exactly the problem! Running smooth again!
Bless you! all i had to do was clean out that little tube on the motor. thank you for sharing your knowledge and expertise!
Thank you for your help
Thank you very much thanks to your video today I was able to fix my furnace just as you stated in this video
Turn your voice up..... you are whispering.
Thank you!
TY!!!
God bless you sir !!!!
Thanks 👍 it's 23 degrees out side and feel like -10 inside watch this video and now it feels like 76 on the beach ⛱️. Thank you A++
Your vids saved me as lot of money thank u may god be with u
Thank you so much, wish I could buy you a beer, appreciate your sharing this. Merry Christmas my friend
Thank you!!!
Awesome man! I had the same exact problem and just fixed it today! Thank You! Tomr is 30* in NYC 🥶
PROBLEM SOLVED! Thank you! I had the same problem that you did. I just subscribed to your channel. Thanks again 👌🏾
Thanks Nagen , that small tube was full of water and dirt on mine , gave it a quick clean and it fired right up .
Man you save me $ tnks for the video I did just that and it works fine now kids are happy and wife is no bothering any more 😃
Not sure why you had to pull the inducer lol just check your pressures with your manometer. Waste of time and money for your customer
Jordan G I didn’t have manometer, just to let you know that was my first time opening HVAC unit