The igniters themselves are only ceramic tubes with an electrode that protrudes through the insulator on one end, and a socket on the other end to accept an electrical connector / wire that goes back to the igniter coil (spark coil). Depending on the replacement part that you buy, the wires may or may not be included with the new part, however unless physically damaged, the wires themselves rarely go bad. If the igniter is wet (e.g., from cleaning) or contaminated with food residue, it may not spark when activated, causing the burner to fail to light. As mentioned, cleaning the igniter electrode end and allowing it to dry will sometimes be all that is needed to restore operation. A problem that I saw on my GE range turned out to be the igniter coil itself - 4 of the 5 outputs from this coil produced a nice fat blue spark at the igniter tip. The fifth output was much thinner (weaker) and often failed to spark at all. Replacing the igniter coil was what was needed to fix the problem. Also, testing for the presence and/or quality of the spark should be done before disassembling the appliance, as the burner units provide a return path to ground that is close enough to the igniter tip for the spark to jump to. Once the appliance is disassembled, there may not be a good path for ground for the spark to follow, resulting in sparking between the igniter coil outputs or sparks jumping from the coil assembly to other locations -- this is not something that you want to happen, as the sparks may create carbon tracks that result in lowering the insulation resistance of the coil pack insulators causing a short circuit path once everything is back together. When working in this area, keep in mind that the igniter coil produces a high voltage, similar to the spark coil(s) in a car. While probably not lethal, getting zapped by this voltage can produce a nasty "bite" and cause the you to recoil from the shock and possibly injure yourself further by coming into contact with sharp surfaces, etc. If you have any doubts about your ability to work on the problem yourself, please hire a professional.

Hello, thank you for creating this video. I cleaned the stove top with easy off and it cleaned yrs off of the burners, but the burners would not ignite, after I had cleaned them. The problem is what you stated in your video. I would have never figured out why the burner would not turn on. I found the needle holes and used a needle and inserted into the pin hole and it worked!! Thanks a million !!!great video!!

Great video, brother, you just save me a whole Lotta aggravation. my entire stove out of the cradle to see if I can get under it. I will order that part now and see if that’s the issue. Thanks again.

Thank you for saving me an incredible amount of time!!!

This is great video.

I thought you had to replace the whole wire thats connected to the tip as well. I have the same problem. I hope your way helps. Thanks

I have the old model of GE profile gas stove with downdraft cooktop. It appears my gas stove head is one piece and I cannot remove the cap like you do. There are two side screws to remove the whole base inside of the cabinet. I cleared each hole with alcohols rub and needle and it still doesn’t work. Is there an easier way to fix the stove heads?

Brilliant idea!

Thank you. Great video

Thank you so much. This was indeed very helpful.

Hey so how do you turn on your oven

I have two that will spark and two will not. How can I fix it

Cleaning it will often work.

@ssingh8166

Жыл бұрын

How to clean it??

@mdblack98

Жыл бұрын

Wire brush or sand paper or brillo pad -- sometimes the eraser on a pencil will work -- just need to shine it up.

Thank you :))))))))))))))))))))))

3:57 pop it back in 4:04 shove it back the hole again -what she said. thanks for the video!

Hi, where did you get the part you replaced?

@masterofnone7243

2 жыл бұрын

I got it on amazon.com for $11. www.amazon.com/gp/product/B00ECV2N3A/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

where did you acquire the new lighter? How does one know which one to purchase? tx

@masterofnone7243

6 ай бұрын

Sorry about the late reply. I bought it on Amazon.com. My stove is a counter top stove so I was able to see the model number from underneath. www.amazon.com/gp/product/B00ECV2N3A/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Why does that happened?

i have the Maytag electric stove and now all four of them doesn't light ups..... hope i could resolves the issues soon.

Thanks for creating this video! I will need to ask my hubby to watch it and replace the ignites😂