If you enjoyed the video, please give it a *thumbs up* 👍 Your support is *greatly appreciated* . Also check out my *STEREO Upgrade* : kzread.info/dash/bejne/fHaitMqDerG0cag.html *REAR SPEAKER Upgrade* : kzread.info/dash/bejne/oYBp3LyBYJy8paQ.html and *FRONT SPEAKER Upgrade* : kzread.info/dash/bejne/i3qYtMeOmqbLpZM.html

EXCELENTE VIDEO, INSTALE ESTOS TWEETERS EN MI COROLLA 2016 Y EL CAMBIO FUE DEL CIELO A LA TIERRA, GRACIAS, LUCEN COMO SI FUERAN DE FABRICA.

I was looking for a video on this like a week ago and you came out with this video. Clutch! Thanks for posting

Excelente!!! Bravo!!! superrr

Thanks a lot for your infos ! I made the project i am very excited.

@CleverFix

Жыл бұрын

That's Great!

Thanks for sharing, made that looks so easy.

@CleverFix

7 ай бұрын

You’re welcome 😊

Excellent job 👏

@CleverFix

Жыл бұрын

Thank you 😀

Thanks for your detailed responses. One last question, do you have a video where you demonstrate the best way to do/best place to put the grounding wire for an amp on a 2014 toyota corolla

Canada man, they sound pretty sweet. The voice and instruments really pop

@CleverFix

Жыл бұрын

Yes they sound great.. It took a few days to adjust, at first I thought there are too many highs, and I turned them down.. but eventually I turned the highs back to normal and it sounds great. I guess I was used to flat music without highs.

@omarandres4665

3 ай бұрын

​@@CleverFixHow do you adjust the highs?

Hi clever fix, I have base model Corolla didn’t came with tweeter can I buy them tweeter and plug and play

Sir,which tweeter speaker best install with sony car tape

PERFECT

Como los puedo conectar si no tengo adaptador?

Will there still be a sound quality increase without an amplifier? I'm assuming these are low impedance speakers if you're using the stock radio

@JosephMustafa-kx6hg

4 ай бұрын

The answer is yes with high sensitivity speakers - like every Infiniti reference speaker they win be louder and cleaerer even on stock

If I dont have a solder gun handy any reason not to use butt connectors here as done with the 6" speakers?

@CleverFix

10 ай бұрын

You could use butt connectors yes. I prefer soldering when possible, that way if there's an issue I know for sure the soldered connection is not causing it. On the speakers I had no choice, because it's aluminum to copper, so it can't be soldered. Make sure to squeeze the connector really well.

Do you think there is a way to keep it looking OEM? (After the upgrade)

@CleverFix

Жыл бұрын

Paint the mount with flat or semi-gloss black paint before installing it if you don't like the white writing. There's no other way, installing the tweeter without it's mount will not sound good (double grill is bad for sound).

is it required to dremel into the plastic? in other words can the new tweeters fit into the OEM housing ?

@CleverFix

10 ай бұрын

They fit, but the tweeters have their own grill. They are not designed to be placed behind another grill, and will sound quite bad. I would rather not do the upgrade than place them behind the grill, that's how bad they sounded to me.

My dog, enjoying the video so far, are you from Hungary? You sound identical to my buddy who lives there. I am doing this same thing for some skar tweets.

@CleverFix

Жыл бұрын

Nice! Skar tweeters are great.. I was going to get some, but it was harder to obtain them than the Rockford, and I figure the quality will be very similar.. The Skar may be louder.

Do you know if they sell the mount part by itself?

@CleverFix

8 ай бұрын

They're sold together,.. Most brands will come with their own flush mount. Check the included items in the manual for the tweeters you're considering, and it should show what's inside as well as the cut-out template, with the width for the hole required so they fit in perfectly. Here's the R1T-S: rockfordfosgate.com/rftech/library/2012/4_speakers/rf_primer1speakers_cutout-irs.pdf it's 1.83" , top right of page 4.

never solder speaker wire. Solder adds a lot of attenuation and the heat does the same. The neat result is more attenuation is less sound.

@CleverFix

2 ай бұрын

Pre-twist and solder properly, and you'll get a good connection. Solder is used everywhere. Even the factory solders from the spade terminal the coil of the speaker, and in the car stereo the pins for the speaker wires are soldered to the circuit board. pasteboard.co/MK5GQgVCE42Z.png

Thank you for this video. I got a question about Bluetooth that is not related to this video. I have issue with my Toyota Corolla Bluetooth. When I get a phone call over Bluetooth, it is very noisy. The other side of the call cannot hear me. Do you know how I can fix it? Thank you!

@CleverFix

Жыл бұрын

Did you try another phone? You have to first find the problem to fix it. If it's bad with every phone, then it's the car at fault. Try another phone first. The microphone is in the dome lights right above you.. so if there's something wrong with the microphone, it could be replaced. Lastly if there's something wrong the stereo, you can try another stereo from a junk yard. I will be posting a video on how to upgrade the stereo with a Pioneer within a month or so.

Why wouldn’t you just mount the new speaker in from the back?

@CleverFix

Жыл бұрын

Double grill for tweeters makes them sound horrible. The grill it comes with is optimized for the tweeter to sound good. Any other grill or obstruction of the sound will reflect the sound and it sounds bad, I tried.

What about capacitors? OEM tweeters have them built in

@CleverFix

Жыл бұрын

Yes the Rockford Fosgates have them built in also, they're at the back, I show them in my Unboxing video kzread.info/dash/bejne/oGxrsbCupqyudMY.html

👍👏👏

Tweeter is to big for mount

remove the letters then it would be perfect

@CleverFix

7 ай бұрын

Spray paint with a Matte/flat color is probably the best.. 3-4 light coats, and it can cover it nicely.