Fore Fuel System install progress on my 03 SVT Cobra

still need to route and mount everything and Clean up all the wiring but basically how i decided to do my fuel system, any advice is recommended in the comments .
i decided to do the "deadhead" routing (mounting regulator before the fuel rails)

Пікірлер: 15

  • @RJon2006
    @RJon20062 жыл бұрын

    My Fore setup is very similar. Glad to see that I plan to mount my filter in the same location as you (although mine is on the drivers side). My lines are routed on the drivers side and I’m using stock rails. Clean install. Very helpful. Well done, sir.

  • @texaseliteperformance4471

    @texaseliteperformance4471

    2 жыл бұрын

    Yea on the drivers side atleast the fuel filter won't be upside down🤣

  • @RJon2006

    @RJon2006

    2 жыл бұрын

    @@texaseliteperformance4471 very true. I need to be cognizant of how I orient mine though. It I orient it parallel to the ground I won’t be able to change the filter without unmounting the whole thing. I’ll do mine angle down so I can unscrew it with enough room and not have to unmount it. I have the massive filter too which makes it more annoying.

  • @texaseliteperformance4471

    @texaseliteperformance4471

    2 жыл бұрын

    @@RJon2006 yea also make sure you don't block the access hole for the lower control arm bolt

  • @RJon2006

    @RJon2006

    2 жыл бұрын

    @@texaseliteperformance4471 good point.

  • @texaseliteperformance4471

    @texaseliteperformance4471

    2 жыл бұрын

    @@RJon2006 but yea I need to make a follow up video once I get my car back from the body shop, my fuel system came out super clean and everything is hidden

  • @racequad9
    @racequad92 жыл бұрын

    Thank you for this video. This is going to help me when I get the time to install my Fore system. Gave me some good tips too. It isn't a pain to re-align the fender if you take it off, is it? And is the main benefit of the deadhead setup to keep fuel temps down? I am not doing a deadhead setup for mine but instead running a cooler.

  • @texaseliteperformance4471

    @texaseliteperformance4471

    2 жыл бұрын

    Yea take some pictures of the fender gap before removing it, and when putting it back start from the bottom up , and use tape on edges so fenders and doors don't accidently get scratched

  • @MrPelletgunguy
    @MrPelletgunguy Жыл бұрын

    Whered you get the mounting bracket for the hobbs switch from?

  • @texaseliteperformance4471

    @texaseliteperformance4471

    Жыл бұрын

    Summit racing insulated Clamp ,I think it was the 1" or slightly bigger

  • @MrPelletgunguy

    @MrPelletgunguy

    Жыл бұрын

    @@texaseliteperformance4471 Okay, thanks!

  • @danielm94437
    @danielm944372 жыл бұрын

    sra swap or 99/01 cobra?

  • @texaseliteperformance4471

    @texaseliteperformance4471

    2 жыл бұрын

    03 cobra, sra swap, will be swapping back to irs soon just need to build it first

  • @racequad9

    @racequad9

    2 жыл бұрын

    @@texaseliteperformance4471 Good man. To me, a cobra is not a cobra without the irs - but to each their own of course.