Rebuilding a 12v starter for a 1953-1964 Ford Tractor
Жүктеу.....
Пікірлер: 23
@anthonyrespass30908 ай бұрын
The thumbnail told me what I was watching until I watching this. I didn't know I had one of these starters in my stable. Thank you good night god bless
@normanott6446 ай бұрын
It’s simple to retract the drive just hold the gear against a stiff wife wheel on a bench grinder and spin it . Leave drive on arm shaft, when barrel spins fast enough it will snap back. The easiest way to pull the brush is tru the window using a wire with a hook on the end. I have rebuilt hundreds of ford starters. Good job.
@AZ34life7 ай бұрын
Thanks for the well done tutorial. A handy tool to use when reinstalling the pole bars is an exhaust pipe expander. After installing the field coils and bars snug the fasteners, using the exhaust pipe expander press the pole bars tight against the case then torque the fasteners.
@david97838 ай бұрын
Mister that is a superb job you've done here. The paint job looks top notch. Thanks for sharing your knowledge and know-how.
@chickenhousemechanic
8 ай бұрын
Thank you.
@chotuusian4127 Жыл бұрын
Good work
@philliphall5198 Жыл бұрын
Been a very long time since I’ve done this and video is bringing it back Got a couple of rebuild kits in shop
@philliphall51982 ай бұрын
I own a rebuild shop at one time in the early 70 , still got parts and latch plus tester machines Not much use anymore 😢😢😢
@kostastsa5 ай бұрын
Can I slightly increase the power of a tractor starter??? it turns slowly as soon as the ambient temperature drops even though everything is fine, the rotor, pipes and cables have been changed. also the battery. everyone tells me it's small but it used to run very well... it's a Lucas brand with a 65hp Perkins engine
@chickenhousemechanic
5 ай бұрын
Don't know of any way to make one stronger other than a bigger/better battery or a gear reduction starter. Being temperature based I'd look at a stronger battery. A higher cranking amp battery will spin a starter faster.
@LisaDollar11 күн бұрын
what is the rebuild kit part number and where can I order it from? thanks
@chickenhousemechanic
11 күн бұрын
Kit is SRK401. You can buy it from numerous places online. Just have to Google it and find your favorite retailer.
@ignacioanaya3403Ай бұрын
what is the color code you used to paint the starter? I like it
@chickenhousemechanic
Ай бұрын
Not sure of the code. It's the ford new holland blue available from new holland dealers. I think it's called empire blue though.
@philliphall5198 Жыл бұрын
My Dad rebuilt starter and Generator I have late and all the equipment to rebuild about any old parts
@philliphall5198 Жыл бұрын
Use hd duck tape under band works great
@philliphall5198 Жыл бұрын
I use very old grower to test armator With 110 ac volt
@chickenhousemechanic
Жыл бұрын
A growler would be nice to have but as few as these I do it's not worth having.
@philliphall5198 Жыл бұрын
And hack saw blade
@mattcasey2602 ай бұрын
And just slide bendix on and put in pin??
@chickenhousemechanic
2 ай бұрын
Yep. Should be a collar you have to slide down on bindex to get pin in.
@kraylake12
Ай бұрын
Im installing a new bendix and cannot compress the collar by hand like you show in the video. my welding clamps are to big to fit in between the starter and the bendix. My carpentry clamps slip off. any ideas on how to compress a new bendix?
@chickenhousemechanic
Ай бұрын
@kraylake12 can you put something smaller into the hole on one side and push the collar down and slide pin in from other? Those collars shouldn't be too hard to push down. They're not weak by any means but they shouldn't be so stiff you can't push it down.
Пікірлер: 23
The thumbnail told me what I was watching until I watching this. I didn't know I had one of these starters in my stable. Thank you good night god bless
It’s simple to retract the drive just hold the gear against a stiff wife wheel on a bench grinder and spin it . Leave drive on arm shaft, when barrel spins fast enough it will snap back. The easiest way to pull the brush is tru the window using a wire with a hook on the end. I have rebuilt hundreds of ford starters. Good job.
Thanks for the well done tutorial. A handy tool to use when reinstalling the pole bars is an exhaust pipe expander. After installing the field coils and bars snug the fasteners, using the exhaust pipe expander press the pole bars tight against the case then torque the fasteners.
Mister that is a superb job you've done here. The paint job looks top notch. Thanks for sharing your knowledge and know-how.
@chickenhousemechanic
8 ай бұрын
Thank you.
Good work
Been a very long time since I’ve done this and video is bringing it back Got a couple of rebuild kits in shop
I own a rebuild shop at one time in the early 70 , still got parts and latch plus tester machines Not much use anymore 😢😢😢
Can I slightly increase the power of a tractor starter??? it turns slowly as soon as the ambient temperature drops even though everything is fine, the rotor, pipes and cables have been changed. also the battery. everyone tells me it's small but it used to run very well... it's a Lucas brand with a 65hp Perkins engine
@chickenhousemechanic
5 ай бұрын
Don't know of any way to make one stronger other than a bigger/better battery or a gear reduction starter. Being temperature based I'd look at a stronger battery. A higher cranking amp battery will spin a starter faster.
what is the rebuild kit part number and where can I order it from? thanks
@chickenhousemechanic
11 күн бұрын
Kit is SRK401. You can buy it from numerous places online. Just have to Google it and find your favorite retailer.
what is the color code you used to paint the starter? I like it
@chickenhousemechanic
Ай бұрын
Not sure of the code. It's the ford new holland blue available from new holland dealers. I think it's called empire blue though.
My Dad rebuilt starter and Generator I have late and all the equipment to rebuild about any old parts
Use hd duck tape under band works great
I use very old grower to test armator With 110 ac volt
@chickenhousemechanic
Жыл бұрын
A growler would be nice to have but as few as these I do it's not worth having.
And hack saw blade
And just slide bendix on and put in pin??
@chickenhousemechanic
2 ай бұрын
Yep. Should be a collar you have to slide down on bindex to get pin in.
@kraylake12
Ай бұрын
Im installing a new bendix and cannot compress the collar by hand like you show in the video. my welding clamps are to big to fit in between the starter and the bendix. My carpentry clamps slip off. any ideas on how to compress a new bendix?
@chickenhousemechanic
Ай бұрын
@kraylake12 can you put something smaller into the hole on one side and push the collar down and slide pin in from other? Those collars shouldn't be too hard to push down. They're not weak by any means but they shouldn't be so stiff you can't push it down.