Obviously originally designed to never have to come apart in service, As usual Ford are happy to pass the costs on to Future Owners when it doesn't work as designed.
@khalidacosta7133
3 ай бұрын
Well considering it's a service item... it should have been designed to be taken apart, like the PSA 1.2 puretech is.
@Pricetaz2 ай бұрын
Me and my old man just done my mums, It's a time consuming job but not too difficult. Just so much stuff has got to come out lol. We did it on the drive with axle stands , took us about 10hours or so all in , I'm sure you're much quicker now with the ramp and your experience. Your videos helped us masively !
@S35CANAVERAL3 ай бұрын
Very good job. I diy these belts,there are 2 widths of timing belt,18 and 16 mm,they went from 18 to 16 in september 2013. When I did the cranckshaft bolt, I used a 3/4 torque wrench for the 300Nm,and set it to the max 450 Nm for the final 90degrees,it actually clicked..I replaced the injector O rings ,one injector popped out the head on removing the common rail,the seal on the tip of the injector can be replaced by hand,Iwas able to slide it back in the head,it can be done. The job is time consuming ,but not difficult I think, and without torque multiplier you definately need a car lift. The coolant bleeds itself in my experience. Really informative video how it should be done,congrats!
@tonyc28373 ай бұрын
Great video. Nice to see a mechanic using a torque multiplier for the crank bolt.👍
@AlexTheGrumpyOne3 ай бұрын
Good Lad! Smashing videos! I must admit i never watch any other videos fully on KZread.. But yours bud are nice and easy to watch with plenty of handy info!
@focus82grothm.843 ай бұрын
The 1.0 EcoBoost engine itself is very good but it's the wet belt that is very sensitive unfortunately for the right oil (5W-20 948b spec) and change the oil and filter at maximum 15000km. Short driving don't help because fuel are getting in the oil and degrade the wet belt. If the car are driven short distances i recommend to change the oil and filter every 10000 km. Along with Ford also Peugeot and Vauxhall has the same problem with the wet belt when its not serviced properly in time and etc. I don't like the wet belt but if serviced properly it should last within the interval of the wet belt. I'm subscribing. Great video 👍
@marcusmaximus4513 ай бұрын
Excellent job I’m very impressed kind regards to you and take care Mark from Billericay 👍😀
@carltaylor74893 ай бұрын
Excellent job 👍
@neilhampson28433 ай бұрын
The best Eco boost video i have watched. Those laser timing tools are good, but very expensive for the DIYer.
@andrewstearn46253 ай бұрын
What we're Ford thinking of when they dreamt this absolute pile of shite up!
@Jack_JJS3 ай бұрын
Another great video Baz 👌
@bryanwalker56783 ай бұрын
My son has a very early 2012 fiesta 1.0 nearing 80k miles so was thinking about doing this but I don't have the timing tools or torque multiplier. Ford quoted £1700 which is silly money to spend on a car of that age, how much do you charge Baz?
@scotspie501douglas73 ай бұрын
great video looks very much like the 1.2 turbo wet belt that vauxhall do terrible belt
@bentbitz12 ай бұрын
Looks like the designers and engineers have a competition to see who can make things the most complicated!
@gibboj2 ай бұрын
nice ,well done sir
@APJ-qi8et3 ай бұрын
What a crok of shit idea, when i first came to the trade, early 90's the old boy who trained me, said any oil on a belt fix the leak and change the belt. NO OIL ON ANY BELT. bad bad idea
@michaelc63253 ай бұрын
Interesting that that focus was a pre face lift car and must be around 10 years old. The oil pick up was clean and the old belts looked in good condition.
@mathewnewton34993 ай бұрын
The reason Ford went from 18mm to 16mm belts was to reduce shoulder wear due to swelling cause by the oil immersion. You should only really see the 18mm belts on older engines (exact month/year depending on model) but all newer engines will have the 16mm from factory. The 16mm belt can be fitted to all ages as no other changes were made. A note regarding the timing cover at 9:44 make sure you fill the little keyway slot above the coolant pump o-ring with sealant to prevent oil from reaching the o-ring and causing it to swell (and leaking). That's the reason the new o-rings no longer have locating tabs on them to allow you to fill the slot in. Newer timing covers don't have the slot. Great idea re the IR camera!
@balanrajan4152
3 ай бұрын
Hi Mathew, my car is 62 plate focus with 100 HP. I checked with Ford for the correct size timing belt. They said I need to remove the belt to visually check and confirm the size if the belt. They can't tell if it is 18mm or 16mm for my car. Can I use 16 mm belt for the replacement if there is 18 mm belt already in it. Please suggest me.
@mathewnewton3499
3 ай бұрын
Hi Balan,yes the 16mm belt is backwards compatible even when an 18mm was originally fitted as there have been no other changes made in that area (e.g. different sprockets). I wouldn't worry too much though as Ford seemingly weren't concerned enough about the wider belt to warrant an immediate change i.e. they appear to have introduced it in stages for different models and, presumably, different manufacturing plants - perhaps to use up existing/committed stock. Furthermore, the change was made only two years or so after first release and I doubt there were all that many (if any?) belt failures in that time and so the design change was likely done as a precaution, perhaps based on input from Dayco as the belt manufacturer based on their experiences with other engines (e.g. the PSA 1.2L Puretech engine has a wet belt and a special tool was released to easily check if that belt had swollen beyond acceptable limits so it is a well-known issue).
@balanrajan4152
3 ай бұрын
@@mathewnewton3499 thanks for the confirmation Mathew. Also I would like to know if doing the replacement of wet belts and water pump would add up the reliability of the car. Can I use the car for atleast another 50k miles with timely oil change. Many users of Ecoboost cars suggest in some forums to not go for wet belt replacement due to failure and get rid of the car. Please suggest me. Also can I use Dayco wet belts and water pump as Ford OEM parts are very expensive than Dayco.
@mathewnewton3499
3 ай бұрын
The wet belt is certainly a serviceable item and so definitely needs doing. The water pump is less critical, however whilst it is not driven by the timing belt (the usual reason for definitely justifying a change) it does need removing to remove the timing cover anyway and so whilst it is off it is arguably worth doing. Dayco belts are absolutely fine and indeed are Ford's OEM supplier and so they will be the exact same belt but just different markings (and prices as you've found!). In terms of furture longevity then, yes, regular oil changes (every 6-7k miles / 6 months is my recommendation) will see you fine. I recently changed the belt on my wife's Fiesta and it was 10 yrs old and had done 75k miles - barely any sign of wet belt degradation and I put that down to regular oil changes (not quite the schedule above - I should practice what I preach!).
@balanrajan4152
3 ай бұрын
@@mathewnewton3499 thank you so much for the clarification. I will go ahead with the wet belt replacement along with water pump and I will use Dayco brand water pump as well. Some suppliers from eBay giving as a whole Dayco kit for less than 200 pounds which contains pretty much everything that includes both belts, water pump, tensioner and required bolts too. I will get back if I need any other information. Thanks again.
@georgegalyer82242 ай бұрын
Done my wife's 1.0 turbo ecoboost 3 weeks ago. 9 years old. 47k miles. All Ford parts!
@georgegalyer8224
2 ай бұрын
Forgot to mention this Fiesta has always had the correct oil at proper intervals and I can't say this enough to people!
@vladbudzinskiy5764
2 ай бұрын
Why at so low mileage?
@Matrox9999
2 ай бұрын
and what you want to say? All ford parts correct oil? You still have almost another 75k km to do it. Everything must looks like new.
@Iced_Diamondz
17 күн бұрын
Because recommended to change at 60k or 10 years. It's been 10 years now.
@PHIL00983 ай бұрын
1.6 zetec all day long for me in this era of focus 🤙🏻
@wulber853 ай бұрын
Do you take the oil pick up off to clean or just do it in place?
@FlixmyswitchLASERАй бұрын
Great video, very informative. On the new ford focus where the turbo is on the rear of the engine, does that indicate a cam chain, and wet belt on the oil pump. Any advice would be most welcomed. Phone ford totally useless. I have 4 local garage giving conflicting information 😭😭😭😭😭😭😭😭😭😭😭😭😭😭😭😭😭😭
@garynewell69473 ай бұрын
I could do with you doing this on my 2015 focus estate
@ticbhouy3 ай бұрын
Does the crank bolt need to be replaced? Just had my car done at an independent garage and they didn't replace the bolt.
@shahislam94503 ай бұрын
What's the book time on the job if you don't mind me asking. Only asking I work for Vauxhall/Peugeot/citroe. We have the wet belts but don't need to remove all of this to replace them
@ukguy203 ай бұрын
Do you have a product number for the o ring and the crank washer? Did you order from Ford and if so are they similarly priced to car parts stores or charge more because they are a ford dealer?
@wacman2 ай бұрын
great video, I need my belt replacing, where are you based? Would be great to get done by someone like yourself who knows these engines.
@245674423 ай бұрын
Do you change just the belt baz, Is there anything else needs doing while you have it apart
@gamesmaster10603 ай бұрын
I wonder if they ever quietly upgraded the material of the belt
@balanrajan41523 ай бұрын
Hi, my car is 62 plate focus with 100 HP. I checked with Ford for the correct size timing belt. They said I need to remove the belt to visually check and confirm the size if the belt. They can't tell if it is 18mm or 16mm for my car. Can I use 16 mm belt for the replacement if there is 18 mm belt already in it. Please suggest me.
@kusamagaming737526 күн бұрын
hey mate one question can I ask you if I can change engine 1.6 tdci mk2 2010 to 2.0 tdci is it possible? or 1.8 tdci with same DMF and clutch etc?
@MX5MAN43 ай бұрын
nice one baz great work!!! those eco boost 1 ltr engines are a nightmare-so many issues with them
@MODemirel
Ай бұрын
why
@MX5MAN4
Ай бұрын
@@MODemirel wet belt issues if you have never seen any of the forums -they all tell you !!
@dm_2184
11 күн бұрын
@@MX5MAN4 Does the 1.5 ltr engine have the same issues?
@MX5MAN4
11 күн бұрын
@@dm_2184no havent heard of any issues on the 1.5
@dm_2184
10 күн бұрын
@@MX5MAN4 okay cheers, heard about the issues with the 1 ltr ecoboost and decided to stay clear
@Chris-mw4fo3 ай бұрын
How much do you personally charge for this ive heard its expensive?
@dylano60333 ай бұрын
Would you recommend a car with this engine?
@Amin-fz3pi3 ай бұрын
How much do u charge and where r you based pal
@benmayne79103 ай бұрын
Need to take your crank pulley alignment pin out dude . After the initial torque . I’ve seen them snap the hole otherwise And I leave The fuel pump . You don’t need to remove it to remove the cam cover . Slides right out no problem
@yordiverhaegh20903 ай бұрын
Question?, with the torque multiplier you have to turn it 5 times 90°, but do you turn it 5 times 90° on te torque multiplier or do you turn de cranckshaft bolt 5 times 90°
@bazmeredith
3 ай бұрын
Bolt
@william81083 ай бұрын
The 18mm belt fits all of them innit.
@tomo8702 ай бұрын
A lot of these engines are nigh on 10 years old now, most of the problems will be from people buying cars with more mistery than history. Skipped services, wrong oil used, general lack of maintenance. Personally i think it is a good engine. I bought an 18 plate C Max with this engine at 9k miles, it's now just shy of 30k. Every 6 months regardless of mileage I drop the oil and filter. No point in cheaping out, just use the fully synthetic Castrol 5-20 which comes in around £60 for 5 litres plus get a decent oil filter. Next service I will drop the sump to check the belt and pick up i think.
@owensmith17903 ай бұрын
Where are you supporting the engine when you’ve got the sump and the timing cover off?
@bazmeredith
3 ай бұрын
Driveshaft mount buddy
@PatricioGarcia1973Ай бұрын
just a question, does the belt get covered on oil due to a problem or is designed that way? I haven’t replaced any other belt that was wet..
@sqwidink1
26 күн бұрын
By design! Crummy idea.
@Imagineering1002 ай бұрын
I thought these were supposed to last 200K .
@phillwilliams33993 ай бұрын
Hi Baz hows it going, can this be done without torque multiplier ? Ive got 1 to do this week
@bazmeredith
3 ай бұрын
Yes it can I've done a few with a massive bar, but they have to be stupidly tight
@chrisibbotson63673 ай бұрын
@bazmeredith. Great video, you know your stuff. I have a late Sept 2018 (68 plate)Focus Ecoboost 1.0 (125PS) ST-Line and until last night was unaware of the wet-belt problems leading to complete engine failure even around 50K miles. Mine is 53000 miles. Been reading up on many forums and Facebook groups, people with well maintained cars with full Ford service history experiencing failures incl brake failures. I have been extremely concerned and scared to drive it. I have seen a number of comments say the Mk4 Focus from 2018 changed to a timing chain. I commented on a post on Ford Owners Club forum asking for advice. A member seen my engine photo and said it was chain rather belt. Is there any way I can send you a photo, or link to one to see if you know if its chain or belt? On the Ford Owners forum I was told that the engine fitted in my car (07 JUNE 18) was one of the first of the new engines. A few days ago the One Show on BBC1 had a section on the Ford wet-belt problems customers have been facing. Ford USA doing a selected recall now on certain models
@labiela8905
3 ай бұрын
Los nuevos motores con cadena de distribución son distintos visualmente, llevan el colector de escape y el turbo detras del bloque. Los anteriores con correa húmeda llevan el turbo delante. De todas formas en los nuevos motores la bomba de aceite es movida por una correa húmeda. Los problemas surgen cuando se utiliza un aceite diferente al homologado por Ford para ecoboost. Incluso en los motores nuevos con cadena, debe utilizar el aceite recomendado por dos razones, por la correa de la bomba de aceite y por la lubricación de los cilindros al tener una arquitectura de construcción y pulido muy especifico. Cuida los mantenimientos, vigila los niveles con regularidad, cuida los tiempos del turbo y tendrás coche para mucho tiempo.
@bazmeredith
3 ай бұрын
Email, link in bio
@derekfleming3095
2 ай бұрын
If the turbo is at the front, its belt The chain driven layout is completely different
@wojciechmazur21403 ай бұрын
Hi. I would like to ask where are you based and how much do you charge for this job. I have s Fiesta from 2019 with 30000 miles on the clock. So I am thinking if I need to change it now or bit later. Thank.
@derekfleming3095
2 ай бұрын
That age and mileage - much later Just ensure regular oil changes with the correct oil
@Stigman1012 ай бұрын
Just had ours done £1200...🤯 no water pump while all apart? ours was good inside belt hard like plastic but no bits 10 years max is the time to change..
@UK_AdventurerАй бұрын
Are the newer Ford Focus' having chains instead of belts?
@FlixmyswitchLASER
Ай бұрын
I have been told that if the turbo is on the rear of the engine it has a cam chain and lower wet belt on the oil pump. But I have been trying to get this confirmed as my local garage says no, two wet belts. Called ford were we purchased the car, totally useless they said call a service agent
@itswais773 ай бұрын
1:56 can’t see the leds on it
@bikeman1233 ай бұрын
Cambelts in oil were such a good idea Ford went back to a timing chain on the 1.0 ecoboost in 2018. I like the new Focus but I'd never buy the wet belt version.
@william8108
3 ай бұрын
I believe Dayco invented the timing belt in oil system!
@joskd8491
2 ай бұрын
Be sure the small belt, driving the oilpump, is also a chain.
@MultiMarafado
2 ай бұрын
@@joskd8491 Oil pump its still a wet belt unfortuly. Hard to understant why they keep it, since you will need to remove the chain to replace the oil pump belt..
@cesarmartingomez196
13 күн бұрын
La cadena sólo la llevan los mhev
@nickmackenzie7033 ай бұрын
Nothing wrong the wet belt cam belt engine, sadly most people don’t change the oil regularly enough. 8000-10000 miles is fine if you use the car/van. Lots of short trips and lack of oil changes don’t help with wear to a cam belt.
@paulas2610
3 ай бұрын
Agree and this goes for all modern engines, wet belt or timing chain.
@joskd8491
2 ай бұрын
there are plenty of examples of engine failure, at low milage and with the correct maintenance. Ford changed the engine to a chain I believe in 2018.
@johnmaurer20352 ай бұрын
Won't be buying one of those. 😮
@cypeman80372 ай бұрын
I had to take my travl sickness pills while watching this.
@MrCKMedia2 ай бұрын
Most useless video…not helping or teaching anyone…
Пікірлер: 84
Obviously originally designed to never have to come apart in service, As usual Ford are happy to pass the costs on to Future Owners when it doesn't work as designed.
@khalidacosta7133
3 ай бұрын
Well considering it's a service item... it should have been designed to be taken apart, like the PSA 1.2 puretech is.
Me and my old man just done my mums, It's a time consuming job but not too difficult. Just so much stuff has got to come out lol. We did it on the drive with axle stands , took us about 10hours or so all in , I'm sure you're much quicker now with the ramp and your experience. Your videos helped us masively !
Very good job. I diy these belts,there are 2 widths of timing belt,18 and 16 mm,they went from 18 to 16 in september 2013. When I did the cranckshaft bolt, I used a 3/4 torque wrench for the 300Nm,and set it to the max 450 Nm for the final 90degrees,it actually clicked..I replaced the injector O rings ,one injector popped out the head on removing the common rail,the seal on the tip of the injector can be replaced by hand,Iwas able to slide it back in the head,it can be done. The job is time consuming ,but not difficult I think, and without torque multiplier you definately need a car lift. The coolant bleeds itself in my experience. Really informative video how it should be done,congrats!
Great video. Nice to see a mechanic using a torque multiplier for the crank bolt.👍
Good Lad! Smashing videos! I must admit i never watch any other videos fully on KZread.. But yours bud are nice and easy to watch with plenty of handy info!
The 1.0 EcoBoost engine itself is very good but it's the wet belt that is very sensitive unfortunately for the right oil (5W-20 948b spec) and change the oil and filter at maximum 15000km. Short driving don't help because fuel are getting in the oil and degrade the wet belt. If the car are driven short distances i recommend to change the oil and filter every 10000 km. Along with Ford also Peugeot and Vauxhall has the same problem with the wet belt when its not serviced properly in time and etc. I don't like the wet belt but if serviced properly it should last within the interval of the wet belt. I'm subscribing. Great video 👍
Excellent job I’m very impressed kind regards to you and take care Mark from Billericay 👍😀
Excellent job 👍
The best Eco boost video i have watched. Those laser timing tools are good, but very expensive for the DIYer.
What we're Ford thinking of when they dreamt this absolute pile of shite up!
Another great video Baz 👌
My son has a very early 2012 fiesta 1.0 nearing 80k miles so was thinking about doing this but I don't have the timing tools or torque multiplier. Ford quoted £1700 which is silly money to spend on a car of that age, how much do you charge Baz?
great video looks very much like the 1.2 turbo wet belt that vauxhall do terrible belt
Looks like the designers and engineers have a competition to see who can make things the most complicated!
nice ,well done sir
What a crok of shit idea, when i first came to the trade, early 90's the old boy who trained me, said any oil on a belt fix the leak and change the belt. NO OIL ON ANY BELT. bad bad idea
Interesting that that focus was a pre face lift car and must be around 10 years old. The oil pick up was clean and the old belts looked in good condition.
The reason Ford went from 18mm to 16mm belts was to reduce shoulder wear due to swelling cause by the oil immersion. You should only really see the 18mm belts on older engines (exact month/year depending on model) but all newer engines will have the 16mm from factory. The 16mm belt can be fitted to all ages as no other changes were made. A note regarding the timing cover at 9:44 make sure you fill the little keyway slot above the coolant pump o-ring with sealant to prevent oil from reaching the o-ring and causing it to swell (and leaking). That's the reason the new o-rings no longer have locating tabs on them to allow you to fill the slot in. Newer timing covers don't have the slot. Great idea re the IR camera!
@balanrajan4152
3 ай бұрын
Hi Mathew, my car is 62 plate focus with 100 HP. I checked with Ford for the correct size timing belt. They said I need to remove the belt to visually check and confirm the size if the belt. They can't tell if it is 18mm or 16mm for my car. Can I use 16 mm belt for the replacement if there is 18 mm belt already in it. Please suggest me.
@mathewnewton3499
3 ай бұрын
Hi Balan,yes the 16mm belt is backwards compatible even when an 18mm was originally fitted as there have been no other changes made in that area (e.g. different sprockets). I wouldn't worry too much though as Ford seemingly weren't concerned enough about the wider belt to warrant an immediate change i.e. they appear to have introduced it in stages for different models and, presumably, different manufacturing plants - perhaps to use up existing/committed stock. Furthermore, the change was made only two years or so after first release and I doubt there were all that many (if any?) belt failures in that time and so the design change was likely done as a precaution, perhaps based on input from Dayco as the belt manufacturer based on their experiences with other engines (e.g. the PSA 1.2L Puretech engine has a wet belt and a special tool was released to easily check if that belt had swollen beyond acceptable limits so it is a well-known issue).
@balanrajan4152
3 ай бұрын
@@mathewnewton3499 thanks for the confirmation Mathew. Also I would like to know if doing the replacement of wet belts and water pump would add up the reliability of the car. Can I use the car for atleast another 50k miles with timely oil change. Many users of Ecoboost cars suggest in some forums to not go for wet belt replacement due to failure and get rid of the car. Please suggest me. Also can I use Dayco wet belts and water pump as Ford OEM parts are very expensive than Dayco.
@mathewnewton3499
3 ай бұрын
The wet belt is certainly a serviceable item and so definitely needs doing. The water pump is less critical, however whilst it is not driven by the timing belt (the usual reason for definitely justifying a change) it does need removing to remove the timing cover anyway and so whilst it is off it is arguably worth doing. Dayco belts are absolutely fine and indeed are Ford's OEM supplier and so they will be the exact same belt but just different markings (and prices as you've found!). In terms of furture longevity then, yes, regular oil changes (every 6-7k miles / 6 months is my recommendation) will see you fine. I recently changed the belt on my wife's Fiesta and it was 10 yrs old and had done 75k miles - barely any sign of wet belt degradation and I put that down to regular oil changes (not quite the schedule above - I should practice what I preach!).
@balanrajan4152
3 ай бұрын
@@mathewnewton3499 thank you so much for the clarification. I will go ahead with the wet belt replacement along with water pump and I will use Dayco brand water pump as well. Some suppliers from eBay giving as a whole Dayco kit for less than 200 pounds which contains pretty much everything that includes both belts, water pump, tensioner and required bolts too. I will get back if I need any other information. Thanks again.
Done my wife's 1.0 turbo ecoboost 3 weeks ago. 9 years old. 47k miles. All Ford parts!
@georgegalyer8224
2 ай бұрын
Forgot to mention this Fiesta has always had the correct oil at proper intervals and I can't say this enough to people!
@vladbudzinskiy5764
2 ай бұрын
Why at so low mileage?
@Matrox9999
2 ай бұрын
and what you want to say? All ford parts correct oil? You still have almost another 75k km to do it. Everything must looks like new.
@Iced_Diamondz
17 күн бұрын
Because recommended to change at 60k or 10 years. It's been 10 years now.
1.6 zetec all day long for me in this era of focus 🤙🏻
Do you take the oil pick up off to clean or just do it in place?
Great video, very informative. On the new ford focus where the turbo is on the rear of the engine, does that indicate a cam chain, and wet belt on the oil pump. Any advice would be most welcomed. Phone ford totally useless. I have 4 local garage giving conflicting information 😭😭😭😭😭😭😭😭😭😭😭😭😭😭😭😭😭😭
I could do with you doing this on my 2015 focus estate
Does the crank bolt need to be replaced? Just had my car done at an independent garage and they didn't replace the bolt.
What's the book time on the job if you don't mind me asking. Only asking I work for Vauxhall/Peugeot/citroe. We have the wet belts but don't need to remove all of this to replace them
Do you have a product number for the o ring and the crank washer? Did you order from Ford and if so are they similarly priced to car parts stores or charge more because they are a ford dealer?
great video, I need my belt replacing, where are you based? Would be great to get done by someone like yourself who knows these engines.
Do you change just the belt baz, Is there anything else needs doing while you have it apart
I wonder if they ever quietly upgraded the material of the belt
Hi, my car is 62 plate focus with 100 HP. I checked with Ford for the correct size timing belt. They said I need to remove the belt to visually check and confirm the size if the belt. They can't tell if it is 18mm or 16mm for my car. Can I use 16 mm belt for the replacement if there is 18 mm belt already in it. Please suggest me.
hey mate one question can I ask you if I can change engine 1.6 tdci mk2 2010 to 2.0 tdci is it possible? or 1.8 tdci with same DMF and clutch etc?
nice one baz great work!!! those eco boost 1 ltr engines are a nightmare-so many issues with them
@MODemirel
Ай бұрын
why
@MX5MAN4
Ай бұрын
@@MODemirel wet belt issues if you have never seen any of the forums -they all tell you !!
@dm_2184
11 күн бұрын
@@MX5MAN4 Does the 1.5 ltr engine have the same issues?
@MX5MAN4
11 күн бұрын
@@dm_2184no havent heard of any issues on the 1.5
@dm_2184
10 күн бұрын
@@MX5MAN4 okay cheers, heard about the issues with the 1 ltr ecoboost and decided to stay clear
How much do you personally charge for this ive heard its expensive?
Would you recommend a car with this engine?
How much do u charge and where r you based pal
Need to take your crank pulley alignment pin out dude . After the initial torque . I’ve seen them snap the hole otherwise And I leave The fuel pump . You don’t need to remove it to remove the cam cover . Slides right out no problem
Question?, with the torque multiplier you have to turn it 5 times 90°, but do you turn it 5 times 90° on te torque multiplier or do you turn de cranckshaft bolt 5 times 90°
@bazmeredith
3 ай бұрын
Bolt
The 18mm belt fits all of them innit.
A lot of these engines are nigh on 10 years old now, most of the problems will be from people buying cars with more mistery than history. Skipped services, wrong oil used, general lack of maintenance. Personally i think it is a good engine. I bought an 18 plate C Max with this engine at 9k miles, it's now just shy of 30k. Every 6 months regardless of mileage I drop the oil and filter. No point in cheaping out, just use the fully synthetic Castrol 5-20 which comes in around £60 for 5 litres plus get a decent oil filter. Next service I will drop the sump to check the belt and pick up i think.
Where are you supporting the engine when you’ve got the sump and the timing cover off?
@bazmeredith
3 ай бұрын
Driveshaft mount buddy
just a question, does the belt get covered on oil due to a problem or is designed that way? I haven’t replaced any other belt that was wet..
@sqwidink1
26 күн бұрын
By design! Crummy idea.
I thought these were supposed to last 200K .
Hi Baz hows it going, can this be done without torque multiplier ? Ive got 1 to do this week
@bazmeredith
3 ай бұрын
Yes it can I've done a few with a massive bar, but they have to be stupidly tight
@bazmeredith. Great video, you know your stuff. I have a late Sept 2018 (68 plate)Focus Ecoboost 1.0 (125PS) ST-Line and until last night was unaware of the wet-belt problems leading to complete engine failure even around 50K miles. Mine is 53000 miles. Been reading up on many forums and Facebook groups, people with well maintained cars with full Ford service history experiencing failures incl brake failures. I have been extremely concerned and scared to drive it. I have seen a number of comments say the Mk4 Focus from 2018 changed to a timing chain. I commented on a post on Ford Owners Club forum asking for advice. A member seen my engine photo and said it was chain rather belt. Is there any way I can send you a photo, or link to one to see if you know if its chain or belt? On the Ford Owners forum I was told that the engine fitted in my car (07 JUNE 18) was one of the first of the new engines. A few days ago the One Show on BBC1 had a section on the Ford wet-belt problems customers have been facing. Ford USA doing a selected recall now on certain models
@labiela8905
3 ай бұрын
Los nuevos motores con cadena de distribución son distintos visualmente, llevan el colector de escape y el turbo detras del bloque. Los anteriores con correa húmeda llevan el turbo delante. De todas formas en los nuevos motores la bomba de aceite es movida por una correa húmeda. Los problemas surgen cuando se utiliza un aceite diferente al homologado por Ford para ecoboost. Incluso en los motores nuevos con cadena, debe utilizar el aceite recomendado por dos razones, por la correa de la bomba de aceite y por la lubricación de los cilindros al tener una arquitectura de construcción y pulido muy especifico. Cuida los mantenimientos, vigila los niveles con regularidad, cuida los tiempos del turbo y tendrás coche para mucho tiempo.
@bazmeredith
3 ай бұрын
Email, link in bio
@derekfleming3095
2 ай бұрын
If the turbo is at the front, its belt The chain driven layout is completely different
Hi. I would like to ask where are you based and how much do you charge for this job. I have s Fiesta from 2019 with 30000 miles on the clock. So I am thinking if I need to change it now or bit later. Thank.
@derekfleming3095
2 ай бұрын
That age and mileage - much later Just ensure regular oil changes with the correct oil
Just had ours done £1200...🤯 no water pump while all apart? ours was good inside belt hard like plastic but no bits 10 years max is the time to change..
Are the newer Ford Focus' having chains instead of belts?
@FlixmyswitchLASER
Ай бұрын
I have been told that if the turbo is on the rear of the engine it has a cam chain and lower wet belt on the oil pump. But I have been trying to get this confirmed as my local garage says no, two wet belts. Called ford were we purchased the car, totally useless they said call a service agent
1:56 can’t see the leds on it
Cambelts in oil were such a good idea Ford went back to a timing chain on the 1.0 ecoboost in 2018. I like the new Focus but I'd never buy the wet belt version.
@william8108
3 ай бұрын
I believe Dayco invented the timing belt in oil system!
@joskd8491
2 ай бұрын
Be sure the small belt, driving the oilpump, is also a chain.
@MultiMarafado
2 ай бұрын
@@joskd8491 Oil pump its still a wet belt unfortuly. Hard to understant why they keep it, since you will need to remove the chain to replace the oil pump belt..
@cesarmartingomez196
13 күн бұрын
La cadena sólo la llevan los mhev
Nothing wrong the wet belt cam belt engine, sadly most people don’t change the oil regularly enough. 8000-10000 miles is fine if you use the car/van. Lots of short trips and lack of oil changes don’t help with wear to a cam belt.
@paulas2610
3 ай бұрын
Agree and this goes for all modern engines, wet belt or timing chain.
@joskd8491
2 ай бұрын
there are plenty of examples of engine failure, at low milage and with the correct maintenance. Ford changed the engine to a chain I believe in 2018.
Won't be buying one of those. 😮
I had to take my travl sickness pills while watching this.
Most useless video…not helping or teaching anyone…