Everyone comments on how thorough these videos are as the thing they appreciate most, and that is very true... BUT what has helped me the most is the fact that these videos ACTUALLY show you or let you hear the issue. This video saved me hours of headache, by actually having the noise the engine makes when having this issue. It's the exact noise mine is making and it is the issue I've been having. So I really appreciate the addition of such steps that others miss. As well as how knowledgeable you are.

@chadmoyer1453

3 ай бұрын

I thank God for him tbh. Very much I do. God bless you Mr. Ford Tech. Lol. Don't know ur name brother.

Almost 8 years later and your knowledge and expertise is still educating and helping thousands of DIYers brave enough to take the plunge. My issue other than over 300,000 miles and ready for a full timing job is a bad lash adjuster on Bank 2. Thank you Brian and please recharge as needed to keep us 3valvers up and running..

I've seen plenty of auto service related video's. Nobody is as through, detailed and patient as you. You really know your stuff. Keep up the great work!!!

@FordTechMakuloco

8 жыл бұрын

+AutoManiac123 Hey thanks I try.

@jasonrutherford1722

5 жыл бұрын

He is the man the world needs more craftsmen like him he is awesome

@adamalloway9761

3 жыл бұрын

Brian, i had 2 different noises. First was bad tensioner i changed that..then i could here the other clicking..teuck kinda sounded like a diesel and wanted to stall when i went to press gas..im about to change the phasers and vcts..question is my oil pressure started dropping out as well..could that be caused by phasers and vcts..also ive already replaced oil pressure switch. Thx in advance buddy

@corrinaseager6587

3 жыл бұрын

My f150 is poping when giving gas and no low power I got the timing chain done and new vat solenoid. Could you give me a idea what it would be

@benjaminschutz727

3 жыл бұрын

Maybe you should take a look at my 2004 heritage f150, I got a code for low fuel trims, tried a smoke test checked the gasket and looked brand fricken new, I also have a oil leak at the oil pan gasket, my reverse gear has a delay, and I have a ticking at the drive thru, also my suspension is squeaky (least of my concerns atm) what part of the US do you live? Was planning a full overhaul as I just bought the truck for 💸 want to restore before I start considering adding a m112 supercharger on the v6

This guy has saved me so much money over the years.

Thank you for explaining this whole process in a manor that is useful. It's always a pleasure to meet someone in our trade that can quickly walk through a repair like this. Not just quick, but thorough too! Relevant information for a mechanics first time replacing cam adjusters on this engine. FYI to any who read what I said here. I would not recommend a first time mechanic try to perform this task. Thanks again my friend.

Thanks for all of the in depth diagnosing. You’ve helped me many times. This one is one that I think I will have repaired by my mechanic. I really enjoyed your sign off, “and that’s all there is!” It’s equivalent to me walking a lay person through a Fire engine pumper explaining about friction loss, length of hose and how many lines a particular house fire will need for extinguishment. Keep up the videos

I just came to get an idea of what to tell a customer. i like the fact that you dont talk to much about things unnecessary. This is vital to following someone's instructions. Yours seem much easier to follow than some others ty Alth0ough I i'm not actually following them for any repair.

Thank you bro! Followed the instructions as you laid them out. Swapped the defective rocker arm with relative ease. Saved me a trip to the mechanic. Again, thank you!

I am retired Tech more on GM side and this video is as thorough and patient as you can get.. great job Buddy hope this helps a lot of people keep up the great work..

I did it. I changed out the phasers. I want to thank you for the video. I don't know that I could have done it without it. it gave me piece of mind and I rewatched various sections as I moved through the job. Many thanks for taking the time to make your videos. My 05 F150 now sounds great. Makes me feel better. It was getting to the point it sounded like gravel was in the engine. I will say that the right valve cover removal was a bear. I removed the a/c collector mount and bent the tubing slightly. Had my pal pull on it while I wiggled the cover out. Used gasket sealer to hold new gaskets in the covers when I reinstalled. Also, I had to remove the right wheel well cover to access the transmission tube bolt. That is a good tip. I took my time. Went slow. But again, thanks to your video, all went well.

Great! Thanks, 7.8 years & You are still going strong 💪

Your videos are changing my life!!! I've been trying to fix up my 99' E150 van and your information has been priceless to me. I used to open up my hood and be too damn chicken to touch anything... but the way you explain things and identify different components has truly helped me familiarize myself with my engine. You demystify procedures that seem shrouded in secrecy and give me the courage to do attempt things I never thought I could. I bought the Ford workshop manual for my van about a month ago and have been going in on repairs. Just wanted to let you know that you really inspired me and please do some more 5.4L V8 tutorials :)

Popping out or reinserting the CAM Followers is a real pain for cylinder 8. The gadget spring compression tool and trying to pry them back in is nearly impossible. Struggled with it for several hours. Then I asked my son for an idea. Genius - He recommended loosening the CAM Caps a little. Worked great!!! Tightened the CAM Caps back down. And this only took a few minutes.

@TekMan05

2 ай бұрын

Yeah I just went through this on my 3v Stang. That tool is virtually useless on cylinder 8 partially because of the brake booster and master cylinder being in the way. I ended up doing the exact same thing. Worked great and spun the engine over afterwards to double check everything before buttoning the cover back on.

You are truly a master of this trade! Thank you very much for explaining this procedure in such detail for anyone to understand. I have had my first experience with the 2 piece plugs and now the cam phasers on the same truck.

Like a surgeon, I wish I lived closer to you guys.

JUST FOUND THE CHANNEL CUS MY SON GRABBED A 04 FX4❤ BRILLIANT BRIAN❤ HOPEFULLY WE DON'T HAVE THESE ISSUES, BUT WITH THIS MAN RIGHT HERE, HAVING THIS KNOWLEDGE AND EXPERTISE WILL HELP US A GREAT DEAL.

I would like to thank you for posting all of these videos, they are very informative. Keep up the good work.

Dude - Your videos are spot on!!! And I agree with others....You're a real Ford tech and you actually makes sense. Thorough, concise, and detailed; well done. As a fleet tech, w/all Fords, I can tell you are legit!

@FordTechMakuloco

9 жыл бұрын

FoxFreak Wow thanks!

My 2005 f150 5.4 is making exact same noise. Threw code for phasers so I'm about to attempt the repair myself, your video has helped me understand. Very detailed, thanks a lot

Thank You for all your direction to those who need your assistance and direction, Your direction is far better than thatI have received from some Ford garages. Thank You

Nice video. Definitely appreciate a visual guide. I read the service procedure and couldn't understand why you're suppose to remove the roller followers but I get it now. Diving into my dad's 06 F250 tomorrow to do phasers, chains, guides and tensioners. Should be fun!

Very detailed, you make it feel like even i can do the fix NOT! Thanks a million for sharing, you are fantastic.

I don't even have these engines, but I watched this terrific video all the way through. You make excellent videos on repair. Thank you.

Glad you had the video. I thought mine had this problem, but it actually sounds like your end result. I can hear the difference now since the first has a harder knocking sound and the end has a softer sound.

I bought a piece of trim moulding and a threaded rod and nut at Lowes for about $6. I cut down the wood just small enough to fit past the phaser and it worked like a charm. My 2004 F150 with 193,000 miles diesel sounding 5.4 is silent and running great!! I followed your procedure with no problems. Thank You for the help

@tonymemory2279

Жыл бұрын

make a video of that.

@chrisjory8595

7 ай бұрын

Def make video of that lol

Thank you for posting this video. Truly is a step by step. Alot of guys just say do this and do that. But won't take their time to show the novice. Again thanks.

Thanks for the video I was about to pass on a really nice expedition that is presenting the same rough running and noise issue

I have replaced cam phasers on a few and some of them said as long as it runs I would use 15-40 oil and I have a few with over 100k after the phasers started making noise no problem. I want to thank you for helping me with lean conditions on 5.4 3v missing rocker on intake never would of looked for that thanks your videos are the best

My mother has a 2010 Expedition with 115k miles on it and it still runs quiet! It's the first vehicle she's kept over 40k miles and several years longer then normal too. It's been a great SUV so far, I'll definitely keep a watch on the cam phasers!

@mcgavin098

5 ай бұрын

Are you always using full synthetic oil? I accidentally switched to synth blend and I've been having issues with my 145,000 miles Lincoln.

Great job...I believe im having this knock issue with my Ecotec with VVT...i had lash adjusters that were ticking when i replaced those i noticed my cam phasers knocking...Figured id c9me and see how its done on a Ford...pretty much the same...Thanks for your help!

Seriously, your walkthroughs and explanations are done very well.

@FordTechMakuloco

8 жыл бұрын

+Robin Rhodes Thank you and they are only getting better now being away from the dealer.

seen alot of videos and yours are by far the best ive seen..very detailed and helpful.

You are always helping me out man, thanks so much!!!

You are the man. To bad you don’t live near me because you would be my mechanic for life.

This noise has been pissing me off for so long in my F150, thanks for finally showing what is causing it. I've had a handful of things done that never solved it.

@junkyardchronicles1289

3 жыл бұрын

Did you fix it?

@thuglivintv824

2 жыл бұрын

Did you fix it?

@ericholderrieth8009

19 күн бұрын

Did you fix it?

amazing videos, thanks for taking the time and sharing your knowledge, can really save the average joe a lot of time and money and from being screwed over by some shop... really really appreciated

Great tutorial and stellar job on the explanations

Great video brother. Thanks.

Thanks for this video. I have a lifter making noise on the passenger side and was afraid to open it up. The manual says to open up the ac system and on post said that is not necessary so that was good. You show that the cam is free after the 3 rockers are out so that takes away the fear of taking the cam out to get to the lifters. I was afraid there would be a load on the rockers and distort the cam when taking on and off the cam bearing supports. Then there was the phaser tool they wanted you to buy to make sure you did not turn the phaser when torquing it down. You again show that that is not a problem. Looks like I might try it. Thanks again for the video.

Thank you! This video, along with many others you've done, has helped me keep my Expedition running and taught me a lot about working on cars! You're the best!

@FordTechMakuloco

8 жыл бұрын

+Leann Sanchez Nice

Dude your videos have saved me tons! Much appreciated!! Keep them up! My fx4 purrs.

you're very knowledgeable. thank you for sharing.

Brian, you make it look so easy! I'm getting an '05 Expedition with 160,000 on the clock next week. I may be doing this job sometime.

From engine noise to final product. I have had my Ford expedition Eddie Bauer 5.4 2003 as my most reliable vehicle. My 6.0 diesel f450 is down just about every month so Old reliable is always there for me. The vehicle is not worth anything but I've kept this one in mint condition and was going to pass it on to my daughter. Tonight for the first time I hear what sounds like a rod knock. My first thought was all this work to keep his vehicle looking incredible and now it went from Old reliable to junkyard. I've never worked the inside of a motor I have tinkered on the outside plenty. I put the stethoscope on the housing that is holding either the injectors or spark plugs not quite sure which one of the two but it sounded like the noise was going to come out of there. When you said mainly on the right side that's when I realized you're showing exactly what I need. I'm not sure if the noise I heard is exactly what you mentioned but it is on the right side is in it it is in the front and with the stethoscope it is really loud. This video is so thorough that I might take on the job myself as a learning experience. I don't think I would have it done as smooth as this is. There may be a lot of bleeding knuckles a lot of screaming walking away for the night and hope that the F-450 doesn't break again. I'm having major transmission issues with that one. Thank you for putting a very good video out there. Most video tell you it was making a knocking noise, already have the car apart and try to explain the noise instead of letting it play on video. I'm not a mechanics so hearing the noise is everything to any DIY jobs.

your the best best teacher

Wow, awesome vid. My brother asked me to do this for him. I was hesitant until I saw this! Thanks!

I hope my mx guy is as dedicated as you... just started to have this problem over the weekend and tomorrow its going in the shop... If I knew this car could make it to Illinois, I would be driving up there this week and have you work on it!!

Thanks for all your awesome information. I worked as a Ford Tec for 4 1/2 years but when the 5.4 3valve came out I left got mine done this weekend. It seems to run good because I started with all 8 coils and plugs all Motor Craft on my late build 08 F150. But your discription of the noise was exactly what mine was doing. I got the truck for $260.00 neeed a transmission that's my line of work. 👍🏻👊🏻💥🤘🏻😎💯

@greenbaysixxstring5008

8 ай бұрын

Some ford tech! You could even diagnose your own problem.

What an outstanding video.

As thorough and detailed as you were, I still got lost haha. Guess I'll just have to rewatch the video a few times. Thnx for the info tho!

Hi Brian, My son in law has a new to him 2004 F-150 Lariet 4x4 5.4L with ~190,000KM (~120,000mi) showing on the odometer. It appears to have had reasonably good maintenance and runs well with no abnormal engine noises, but it is throwing a P0011 DTC. We've been doing a lot of research on the subject, especially from your videos to try and educate ourselves as to what the problem could be. The previous owner told us that the cam phasers were replaced with aftermarket units a few years ago. We reasoned that the most probable cause was either the VCT solenoid, or the phaser itself. The solenoid coil resistance was 8.5 ohms, which seemed reasonable. We did a data log under real world road conditions with his scan tool and it showed that when the cams should be retarded both were being commanded by the PCM, but the commanded PWMs were different, which makes sense considering the code. The error on the left bank was normal and the left cam was being retarded. The error on the right bank was high and the cam was not being retarded at all at. We swapped the cam sensors to see if the problem would follow the sensor, but it did not, which lead us to believe the problem was either a stuck or faulty solenoid, or a stuck phaser. We purchased a new OEM solenoid and seal from our local Ford dealer and installed it. No change. So, it looks like it is most likely the phaser, but we want to be as sure as we can that this is in fact the problem before we commit to doing a complete timing set with OEM parts. In all our research we haven't run across a situation where a phaser has stuck in the fully advanced position with out resulting is some engine noise. We do have an exhaust leak on that bank which we will have to address, but we can't hear anything that seems to be internal, either under no load or under load. Have you had an experience like this, or can you offer some suggestions as to what else we can check?

Very thorough & extremely well explained video - great job - thank you

The 4.6l 2v has been around since the early 90's. It has been a damn good engine. The 3v 4.6 and 5.4 seem to have had their issues.

@oliverdelgado6952

5 жыл бұрын

Stay away from 5.4 3v. Unless you absolutely know it's had frequent oil changes .

@timdixon9224

2 жыл бұрын

You are best to use the Motorcraft oil and filter always on these engines

@madebydade305ify

2 жыл бұрын

Was there 3v in the 2003 f150?

Noise speeds up with more rev, and but doesn't seem as bad if it is at around 800-900 rpm

Thank You very much an excellent video and outstanding explanation!!!

This guy is the king and master 💪 💪 💪

since you are the only reliable ford guy on KZread, what are the odds to find a piece of metal Inside the Intake manifold, when I removed the intake to replace the gaskets while cleaning the intake I noticed that something was loose inside so when I shook it upside down a piece of metal fell down and it looks like what I can describe as an edge of a broken valve, could that have been sucked from the engine into the manifold? also if this is the case is there a way I can replace the valve without taking the head off, or I am I looking at buying a new engine? thanks a million

@FordTechMakuloco

9 жыл бұрын

certified30 If the edge of the valve was cracked off it would have a misfire on that cylinder it must have come from before the intake. I would reassemble and retest. Was this the reason you pulled the intake in the first place?

@KaliBlaz

9 жыл бұрын

FordTechMakuloco initially I had a ticking noise, I thought it was the cam phasers dying but after I changed the spark plugs that noise went away, and recently I had P0174 code and the truck was running very rough and shakes a lot so I decided to change the intake and throttle body gasket..etc to eliminate the vacuum leak probably, but when I pulled the intake I noticed that there was something loose inside it, it was a piece of metal that looks like a valve edge, I am just hoping it accidently fell in there when the throttle body was being serviced by the previous owner. at the same time I am asking my self if it is possible that the intake have sucked it in from the engine!!

@hectorcaballero3904

6 жыл бұрын

i had the same problem , but what haoppened is , someone else replaced the engine and dind t get out the pieces of valve from the plastic plenum, if your engine runs good, the metal piece is from a previous repair, all you have to do is take the plenum, if you have a misfire, check your compression and obviously the cylinder with low compression is the one that that piece of valve belongs to.

@elwoodgilbert7340

6 жыл бұрын

certified30

Great, great, great video. Very detailed and easy to understand. Thank you very much for taking the time to do this for the benefit of all of us! I've completed the cam phaser block, chains and guides with no problem after watching your videos. At just about 1000 mile after complete phaser job, when engine is cold, I get a puff (sometimes big puff) of blue smoke out of the exhaust which I didn't have before. Smoke clears up within a couple of seconds. Engine is stock 5.4 3V except for the phaser block and Livernois ECM reflash. Engine has 85K mile in 2004 F150. No oil useage, just the puff. Any ideas FordTechMakuloco? Thanks again.

@FordTechMakuloco

8 жыл бұрын

+Bryan Paris if you just changed the phasers I would say it has something to do with the kit you installed otherwise if you removed the roller followers I would check the valve stem seals for tears.

@robertswift6101

7 ай бұрын

im getting the same puff of blue smoke on my 07 mustang with 50K miles on it,,it goes away after it starts..i change my oil every 3000 miles,,,my guess is also the valve stem seals,,,i thought it might be the pcv valve but their isnt one,,,just a tube,,,i`ll be adding a catch can seperator on both sides also,,,but it looks like from what i have seen on videos is the valve seals are bad i guess....total bummer

Great video !!! Very clear and precise. Thanks

Thank you so much, I really appreciate your time and SHOWING what needs to be done and WHY the details are important

This engine is Jasper's #1 selling reman engine,can't keep them on their shelves.The Jasper rep that stops at my father sells at least 5 of them a week.There is a Melling M360 oil pump out there for these with a cast iron backing plate.

@waden404

4 жыл бұрын

Does that mean Jasper sells the reman with a "fix" to this issue? Im getting ready to pick up a pristine 99, but the engine is toast.

Are you in Georgia? I would like you to fix my truck

Very well done. Experiencing this on my Expedition, especially at drive throughs. Sounds like a tractor.

How many guys are actually capable of making this repair even with this great video??

Do you have a video on the 5.4l 3v lifter replacement on the passenger side? Thanks for all the useful videos.

@FordTechMakuloco

8 жыл бұрын

+amtpdb1 No but lifter replacement is basically the same as what I show in this video with the roller follower removal tips. Once the follower is out of the way the lash adjuster can be removed.

@amtpdb1

8 жыл бұрын

+FordTechMakuloco Thanks for getting back. I do need to take the cam out to get the adjusters out don't I? Can you get some of them or all of them out with out removing the cam? It would help alot if the cams don't need to be removed. Can you get the valve cover off on the passenger side with out discharging the AC? Some say you can and some say you can't. Great videos and I will be watching all of them as the truck is starting to need repairs! Thanks again I appreciate your videos and responses.

This guy has the face of someone who’s gonna upset the crap outta you

@jcortes3930

4 жыл бұрын

😂

@jeanvi52

4 жыл бұрын

You have the face that makes me wanna beat your sorry ass down in the street

@hamsandwich9311

4 жыл бұрын

That's because he's pointing out problems with your sorry ass 5.4 motor.

Great video my man. Pushing 300k on my 08 navigator. It started knocking loud, like very loud and misfiring alot. Will be doing the phasers now.

Your a great teacher sir! Awesome video and topic on the 3v 4.6 and 5.4L.

My Ford F-150 makes the same noise. Will any damage occur if it is not fixed? I'm not too convinced on shelling out a couple thousand to just fix a noise.

@FordTechMakuloco

9 жыл бұрын

metersocket00 No for this noise no.

@KollynJ

4 жыл бұрын

FordTechMakuloco what noise is it that is more dangerous?

Mines been ticking since I bought it, doesn’t bother me. I just recently got a cat back exhaust and don’t even hear it anymore

@amoncopeland6747

3 жыл бұрын

Yea that was me. It will go limp one day. Its like you only have 2 cylinders when it gets stuck in retard. I did just phasers and solenoids. Runs better than any truck I have ever owned now.

@juannavarro8659

3 жыл бұрын

.

@mikeroland9751

3 жыл бұрын

@@amoncopeland6747 Question: I just got a 2004 F150. I drove it from Arizona to California. Ran great. Now, I have code P0174 "System Too Lean (Bank 2) and I can not find any vacuum leak anywhere...God knows I've tried. I also have P0022 "Intake Camshaft Position Timing Over-Advanced" (Bank 2) The question is: Could the CAM POSITIONER be the reason Bank 2 is registering Too Lean since it's over advanced or is it over advanced because it's trying to compensate for too lean?

@amoncopeland6747

3 жыл бұрын

@@mikeroland9751 bro.. Thats a good question. My initial answer would be no. You would have experienced some other problems. . do you have cold air intake or anything like that?

@amoncopeland6747

3 жыл бұрын

@@mikeroland9751 the camshaft advance could be more worrisome. I bet your lean is a broken injector loose connection on injector(lectrical) or a dirty map sense? Just my thoughts. Cam just opens and closes valves. (Or doesn't when broke) i would be looking at all air sensors and look into fuel module and stuff. Any rain there?

I just had mine done @103k miles, 08 expedition. Was making noise every since I bought it with 72k miles. Who knows how long it was doing it before me. Dealer did not want to fix prior to deal so the gave me an ext. warranty instead. In hind site I'm glad we went this route because they would have fixed nothing more that what absolutely needed it. So I would have been doing it over again. Sounded like a rod knock. Just driver had bad phaser. Chain was so loose it's a wonder it did not jump time. Did phasers both sides, chains both sides, tensioners both sides, guides both sides , oil pump , water pump and belt. Some of the work was "just because" it was open to do it and not have to tear it back down later .... HOPEFULLY thank god one side was covered by ext warranty. Still cost me $1k vs $4k which in my opinion would have been a new motor if I would not of had warranty. I have gotten good use of the warranty to. Lots of money saved. I guess I'm kinda disappointed on the other hand of quality of Ford and all the expensive repairs needed. Thanks for the great videos you make sir!!!! Mike Tiffin ohio

This is probably my 10th time writing a comment or review to this video Great explanation great great video Thank you so much to understand what it causes this noise

Hey I have a knocking noise on my 03 expedition 5.4l 2v it does it on every cold start and it gets quieter as it warms up. Any advise on that issue?

@timdixon9224

2 жыл бұрын

Those don't have the cam phasers in them. I would bet the timing chain guides are broken.

Great video. Quick question. I see how you recommend getting the engine in a nutral position and remove the 3 rockers from each side but on other videos I see them remove the phaser without those steps. Is it absolutely necessary? What's the benefits of doing so? Thanks. Keep up the great work.

@FordTechMakuloco

9 жыл бұрын

chris paikai If the cams are not neutral they cam pop over and you will be out of time then it happens so just take your chances.

@fernandoguerra9783

7 жыл бұрын

+FordTechMakuloco mine pop over, where should cam lobes be when crank is at TDC??,

@Chicken_JAC

2 жыл бұрын

@@FordTechMakuloco Good morning Thank you for your very informative and teachable videos ! Do you have good experience or recommend Cloyes cam phasers? ( as OEM's are hard to find) Thank you again sir Alfonso

Great video. Thank you!

Thanks man ill go ahead and do that tomorrow Also here is a link to the video of the noise my truck gives off 5.4L 3valve 07 problems with the engine

what happened to the ol' 300 inline 6. this 5.4 is way to complicated..... it was still ticking and knocking after u were done. I have a 2004 5.4 and that motor sounds like it's falling apart. also a 96 z71 that u can't hear run and it gets better mpg..... not thrilled with my f150

@gilbertopadilla3611

7 жыл бұрын

ben shepherd At 230k and a hard life, my 4.9 i6 still purrs like a kitten.

@Miamiboi305

6 жыл бұрын

Why do you have to pull those roller followers no other video u've seen has done this

@coypatton3160

5 жыл бұрын

Emissions happened to the inline 300 6!

@benricher9717

5 жыл бұрын

@@Miamiboi305 Its due to having the cam in the neutral position. if you dont do this, the cam will want to spin due to the spring tension on the cam lobe. by relieving hte pressure on these lobes, the cam no longer wants to spring forward or reverse causing in accurate time marks.

@jeffanderson7256

5 жыл бұрын

I love the 300 6 but it’s only upside is it lasts, and oh boy does it last you could drive those fucking gutless turds 24/7 for a decade I bet

whats your take on the livernous lockout kit for phasers , does it hurt or help ?

@alexr6676

7 жыл бұрын

Henry Ford Hello Henry did you get an answer to your question about the locking phacers?

@luckyone9473

6 жыл бұрын

As a certified 5 Star, triple OG Ford Master Tech I do not recommend them.

Great channel. Your commentary is always spot on - useful info with no fluff. I rellay benefited from the Taurus reap brake video (I hate drum brakes!). My '06 5.4L with 250k is making this exact noise. Stethoscope shows right side. Changed oil and Motorcraft filter, 5W-20, had 60 psi at startup, outisde temp 75. Driving around for 10 minutes had me at 10 psi with no increase with RPMs. Stopped engine, waited 2 minutes, then had 35 psi at idle. I think bearings are fine since I have 40 psi after startup (not enough time to cool down) so timing chain tensioner seals seem most likely. Sound right?

We replaced the phasors on a 3v and it still had the problem.Cam timing on left side would go crazy when engine was hot and off idle,so computer tried to compensate by adjusting the right cam.We now suspect it was a clogged oil passage in head or block somewhere.Customer said to fix it but it was just a guess on our part.So we sent him to the dealer to confirm,because that is a big expensive gamble.

So am I correct in assuming that the noise IM hearing on the 5.4 I have at work that makes it sound like a diesel are the Cam Phasers themselves?

@FordTechMakuloco

9 жыл бұрын

FBobby Yes

@FBobby

9 жыл бұрын

FordTechMakuloco Good to know. Thanks for the reply.

@amoncopeland6747

3 жыл бұрын

Yea. Or loose plug.

i have watched some videos of the people removing the rockers and some do NOT remove the rockers? is it completely necessary to remove the 3 rockers on each side? thanks

@FordTechMakuloco

8 жыл бұрын

I would if its your first time but I have an updated video just released.

@AlanDike

5 жыл бұрын

@@FordTechMakuloco I think I saw your updated video, and it says only on the left hand side? Why doesn't it work right hand too?

Great video, am I crazy as a learning at home mechanic to try this job? Your video makes it seems pretty straight forward...

thanks....great video.....love the step by step approach,,,,,bob

Mine ticks too, sometimes it goes away after its warmed up. it's done that as long as i can remember

@HannibalAcrotices

3 жыл бұрын

Has that been years? And is it still running alright?

@jacksimi

3 жыл бұрын

I’ve had it 7 years now. It has about 270,000kms on it. I bought it used. I just change the oil regularly, I’ve changed the spark plugs twice myself. Other than that it runs great.oh and I did have to change the fuel sending unit, they mount them right by the spare tire underneath the box. The salt here eats the case. But that’s just a plug it in fix and maybe 2 bolts. If you’re not in a salty area you’ll be fine.

@luvbootys

3 жыл бұрын

@@jacksimi is your truck still working

@jacksimi

3 жыл бұрын

@@luvbootys Yup still going strong. I find if I use a ford oil filter it helps a lot. But it still runs fine, No issues or codes. I've changed the plugs 2 summers ago. Other than that it runs great.

@luvbootys

3 жыл бұрын

@@jacksimi I have a 2004 ford f150 triton 213,345 miles no check engine light has power runs great but it sounds like a diesel when it's warmed up any ideas of what it can be someone said can phasers but it sounds quite on on a cold morning start

where do you work? I'm sick of the Ford Techs here, I have spent over $3,000 in repairs since January, and today I sat in a parking lot because my entire truck would shake and rattle when RPM's went over 1000 rpm, I have replaced Tensioners, phasers, chains, guides, solenoids, plugs, coils, I'm just about ready to trade it in if I can't get this thing to be more reliable.... 2005 F-150 5.4 w/ 158k miles

@FordTechMakuloco

9 жыл бұрын

I run my own business now in Chicagoland

@orlandovega6958

6 жыл бұрын

I feel You! I have an '06 and it rattles when driving at 45mph the stops and starts again at 55. I have a check engine light one and the code is for a misfire. Took it to a shop and the said it might be the camshaft or bad timimy chain. In order to find out i have to drop another grand on it. And I just got the tranny replaced after it gave out, then this starts a couple of weeks later. It's only got 130k miles

@MMMM-jr5uf

6 жыл бұрын

Orlando Vega me too just fixed the tranny and having the same exact problem you describe were you able to fix it?

@orlandovega6958

6 жыл бұрын

Mm mm no, it's just been sitting there. No time

Still, an awesome video 5 years after you made the video. Simply awesome !!

Great job in explaining everything... Funny thing.im just finishing doing one on a 05 expedition but mine had also a broken guide..

@FordTechMakuloco

10 жыл бұрын

Interesting we don't see that too often.

@guayaco-dm3vu

10 жыл бұрын

Neither do we but just the fact the it would rattle upon revs made me take the timing cover of inspection.

I already had a ticking sound I was told it was normal. But now i have ticking AND knocking

@michaelH0000

2 жыл бұрын

Same!! Hows engine? You fix?

@michaelH0000

2 жыл бұрын

My knock get really loud at 1000rpms

Damn! Man! Give me a rebuilt 351 w pushrod motor and Id be happy!

Very clear instruction! Good vid

Just performed this today on my 2010 4.6 stx 4x4 with 130xxx miles. Thought maybe it was a rocker or a lifter but come to find out it was the phaser because after the oil warmed up and thinned out you could hear knocking noise. No more knocking. The camshaft did turn while I was putting in the new phaser but thank goodness I marked it. Grab some vise grips and turned it back. Now I just got to figure out why the truck almost has a shutter while driving. Local transmission shop said wasn't the transmission. Put on a new transmission mount and I still have a problem. Wondering if it needs a whole new timing chain now. Thinking about just driving to your shop @fordtechmakuloco. Thanks for all the help so far 👍

I was in the market for a 04-08 f150..... not anymore good lord

@Aaron-is5fn

6 жыл бұрын

I have one put 115k on it has 315k runs fine one og motor and tranny

@datsie14

6 жыл бұрын

Phillip Turinsky mines been great to me they work great if you take care of them. Synthetic oil. Fuel filters and oil filters regularly and you should be fine

@josephgarza2586

2 жыл бұрын

They are good motor runs 400k with good maintenance failures are dou to none oil changes

OK so my truck 2007 f150 5.4 is reading code p0012 I replaced both cam sensors and both VCT my truck still ideals rough and starts to sound like a diesel, it gets really bad and starts to ideal down and when I keep driving it when I come to a complete stop it ideals down and dies out

@brewmonsta6413

7 жыл бұрын

Richard Anthony ever found out what it was?

@johnnybrown1475

7 жыл бұрын

BrewMonsta I have an 03 that sounds like a diesel found out its coming from Trans which has major problem apparently. Google it...hope that helps, I'm in process of looking for Trans now.

@marcusysaguirre8561

6 жыл бұрын

Replace Cam phasers

@ceethelight1239

6 жыл бұрын

Ha Richard I'm having the same issue on my 2007 f1504x4 130.000 miles got a new timimg chain ford has went back in it and cant find whats causing this problem can you help me please thanks

@frodofraggins319

6 жыл бұрын

ceethelight 123 you need a thicker oil. 15w 40

Wish I lived in your area, you would be my mechanic. Great videos, tons of useful info. 2009 f-150 5.4

@FordTechMakuloco

9 жыл бұрын

Sweetsauce Well thanks!

@russhancock78660

4 жыл бұрын

FordTechMakuloco I’m thinking an older higher f150 I’m late to the party could you tell me where your shop is?

was going to pay to do these.... not anymore! I am confident with your video. thanks bro!

Shoulda bought the 5.0 I can't stand those 4.6 and 5.4s.

@FordTechMakuloco

10 жыл бұрын

That's for sure.

@MicroOrginisum

10 жыл бұрын

Both 5.4 and 4.6 are great engines. Just had a little trouble with some of the years. The new 5.0 is just a slightly bored and stroked 4.6.

@231mac

9 жыл бұрын

Al Lewis The new 5.0 has absolutely nothing to do with the old 4.6. Completely different animal.

@ironDsteele

9 жыл бұрын

Al Lewis The 5.0 is a 4 valve engine. I don't know where you got your info from.

@michaelklein7105

6 жыл бұрын

Thanks! That's probably the sound I've noticed for some time coming from the right side of my 05 Econoline. Now, at least I have an idea what is the matter. Not an easy of an fix for a Van. Thanks again brother!

Why is the noise more common on the right bank?

@FordTechMakuloco

7 жыл бұрын

That bank and phaser is the last to get oil

@adamhammond4820

7 жыл бұрын

Any recommendations? I've replaced both phasers and the right phaser went out again at 7500 miles. The left phaser makes absolutely no noise.

@FordTechMakuloco

7 жыл бұрын

Well first is to use Ford parts if you are not already second it an oil pressure test it should be 20psi or higher hot idle. Also is there any startup rattle noise?

@adamhammond4820

7 жыл бұрын

Well that's another question I had. There was a rattle upon startup once the new cam phasers were install. I assumed I messed up a tensioner when I used the wedge to apply tension while installing the new phasers. I installed both phasers the same way. I installed a lockout kit to try to reduce the knocking and the rattle stopped but the knocking just got a little quieter.

@adamhammond4820

7 жыл бұрын

Well that's not really a question but you know what I mean

Looks like you in Illinois ..Would have used you in a heartbeat for my mechanic..thanks for vids.

i love the way u do the rocker arms great job and tip