I know this is an old video but I’m still learning how to use my noble from you to this day Thankyou 👍

@WTFRCCars

10 ай бұрын

Glad ya like the vid :)

Thanks for all your videos on the nb4. They really help!

@WTFRCCars

2 жыл бұрын

Glad ya like em :)

This was very helpful! Thank you!

@WTFRCCars

3 жыл бұрын

Glad it was helpful!

again simple and informative

@WTFRCCars

2 жыл бұрын

Thanks 👍

Definitely looking forward to the other video you are going to do about setting the duel rate to a button or dial. This is my rookie season doing NoPrep drag racing. As of now I only run 15% on my Steering epa. It would be nice to just be able to push a button after the run & have full steering to turn around & bring the car back.

@WTFRCCars

3 жыл бұрын

Soo as I get time I'll do the vid :)

@mikeburgessrc5360

3 жыл бұрын

@@WTFRCCars yeah no rush it’s just nice to actually have some type of guide for this radio. Definitely appreciate the video’s.

@WTFRCCars

3 жыл бұрын

Glad ya find them useful. )

Excellent thanks

Helpful thanks

@WTFRCCars

11 ай бұрын

No problem :)

Thanks mate. The green slider at the bottom of the screen, I can’t figure out what the purpose or benefit is? When I pull full acceleration the cross hairs only go to around 90%, and just 40% on the brake. I don’t feel like I’m missing out on 10% acceleration or 60% brakes, but I’m just surprised the throttle at least doesn’t go to 100% to match the rate setting of 100%. The brakes has less throw on the lever from neutral so I guess it’s distance based. Confused. Thanks again for this awesome NB4 content!

@WTFRCCars

3 жыл бұрын

This sounds like you have the throttle and brake endpoints set and so it's restricting the travel.

@Saint_MUFC

Жыл бұрын

@@WTFRCCars I just picked up an NB4 and have been religiously watching your content, thank you. I am also having the same issue as the above post even with my endpoints set to B-100 F-100 the throttle never goes past 62 and the brakes about 30

@WTFRCCars

Жыл бұрын

Reset the model memory then calibrate the nb4 :)

@Saint_MUFC

Жыл бұрын

@@WTFRCCars so I tried this and it didn't work however I have solved it. You have to do the stick calibration on the transmitter (Settings > System > Stick Calibration). Once you do that the throttle and steering crosshairs go to 100

@WTFRCCars

Жыл бұрын

Yeh that's what I ment by calibrate the nb4 :)

I’ve got weird problem with throttle I’m running a hw 13.5 spec I70 motor with hw xr10 spec 1cell which I have on my 1/12 scale pan. My problem is when I hit throttle it runs like 2 seconds then quits Motor and esc wired up correctly not sure if in esc or noble any suggestions I’ve never had this problem in last 6 years. Thanks

@WTFRCCars

Ай бұрын

Check that the transmitter and receiver are on the same firmware by updating the receiver from the transmitter menu. So long as this is correct and the channel is staying where you hold the throttle then I'd say run calibration on the esc, also make sure lvc is not set too high in the esc :)

@wildcardjoker

Ай бұрын

@@WTFRCCars I noticed just below ur reply I had the same trouble on 1/12 scale pan car. Come to find out it was sensor wire I had to change wire 3 times and on the 3rd wire it work fine. Thanks for quick reply

@WTFRCCars

Ай бұрын

@wildcardjoker all good to know :)

I just got this radio today, which reciever should I use for my drag car? it comes with 2, Thank you

@WTFRCCars

2 жыл бұрын

Both should be fine to use the fgr4 has more range though

@WTFRCCars

2 жыл бұрын

The fgr4b is also a good one to use as it's got good range very small and allows you to set a polling rate for each channel so you can run a 1000hz servo for crazy fast steering and still a 330hz ESC :)

Just purchased and built 1/12 pan car have the hobbywing 1c esc and reedy17.5 s plus motor. It will run for bout 6 secs kinda slow then stops checked car over good sensor wire solder joints etc esc when plugged in program box tired 4 and won’t connect to esc. Well got new esc and same problem so I changed motors and runs few seconds then dies. Runs til I get 40% on trigger and anything over shuts it down. After it dies if I let off trigger then back on runs another 6 secs. Thinking it’s in settings on noble transmitter any suggestions. Thanks

@WTFRCCars

3 жыл бұрын

What do you have the servo poll rate set at on the nb4?

@wildcardjoker

3 жыл бұрын

@@WTFRCCars figure out it was sensor wire thanks

@wildcardjoker

3 жыл бұрын

U ever get a chance to do abs on Nobel

@WTFRCCars

3 жыл бұрын

Yeh did it a few vids back kzread.info/dash/bejne/hIFpz9WMicScddI.html

@wildcardjoker

3 жыл бұрын

@@WTFRCCars thanks

Are you from Yorkshire?

@WTFRCCars

2 жыл бұрын

I most certainly am not lol I live on the Derbyshire/Nottinghamshire border :) it's not that far off though tbh lol