Great video. I had an almost identical problem but instead of a shoelace it was a draw string from a hoody. The noise produced by my drier was nowhere near as bad as yours and was intermittent but with help from your video I got it sorted. Gave it a good clean out and recorded the ptno for the bearing while I was there 608 - 2RS HB with ceramic balls also used on skateboard wheels LOL. Many Thanks

@georgesworkshop8600

Жыл бұрын

Hi Stephen, Good job! Thank you for your words

Thank you. You've just saved me a new tumble dryer if I can get this back together again

@georgesworkshop8600

2 жыл бұрын

Hi Julian, I hope you could finish it.

@suffolk-fun

2 жыл бұрын

@@georgesworkshop8600 my bits are now a working tumble dryer again 😁

Thanks mate, so glad i watched this. Had this annoying noise for a few weeks, i was about to give up and scrap it lol.

@georgesworkshop8600

3 жыл бұрын

I’m so glad I could help

my wife found a bit of metal in the clothes and threw it away. When she described what it was I think it was the sensor bar. Do you have any ideas where it fits as I can’t really tell where it’s missing from?

@georgesworkshop8600

27 күн бұрын

Hi, One place could be where the daily filer located. You need to remove the filter like clean it. Or, in the inner plastic frame of the door, on the top. It’s better to remove the front cover while you fix it.

I'm experiencing a similar noise with this model. So was the shoe lace the source of the noise? Did no parts needed replacing?

@georgesworkshop8600

14 күн бұрын

Hi, In my case the shoelace was the issue, I needn’t any parts to replace

@SkippyVinyls

14 күн бұрын

@@georgesworkshop8600 thanks, I opened it up this afternoon and found some wear around the bearing. But also found some chewed wires. A mouse must have got inside. So I've to more parts to order.

iv got a loose screw stuck between the drums, how do I get between the drums to retrieve it ??

@georgesworkshop8600

3 жыл бұрын

Hi David, I cannot advise without seeing it. Could you please send a short video to show the problem? Thanks

Hi, any idea what error F19 is? I have this along with F12 and the dryer will only stay on for about 5 minutes before switching itself off. Looks like the same model. Thanks!

@georgesworkshop8600

Жыл бұрын

Hi, Will try and help with your Hotpoint condenser Tumble Dryer TDWSF83BEPUK problem. Google says: F12 Electronic control fault It might be worth looking for a second-hand machine with the same model number that might have a different fault and then ransacking it for the control board and you would be able to try some other parts or fix that machine with your parts. I would not recommend buying a new control board until you are 100% sure that this is the problem as it is not a cheap item.

on my dryer all of the lights are on apart from anti increase and is not responding. i have cleaned everything but still the lights are flashing and is not responding

@georgesworkshop8600

2 жыл бұрын

Hello, I have another video where I dealt with a similar problem. Could you please watch and follow it. I believe the drum sensor need to be replaced, that is cheap and you can buy from ebay. If this won’t help, then probably the heating element with all sensors should change. If you buy the whole unit completely that is cheaper, than buy separetly the sensors . I hope I could help.

Any ideea about f01 error ?

@georgesworkshop8600

2 жыл бұрын

Hi Google says: F01 - Electronic circuit board fault Issue: Tumble Dryers is not operating - some or all functions are not selectable. Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again. Advice: If the fault remains, please call our customer service centre to book an engineer

My belts just gone on the same model 😂 any advice? Cheers

@georgesworkshop8600

2 жыл бұрын

Hi mate, Watch kzread.info/dash/bejne/e5-nk6ixddu2k8o.html this video. This is about belt replacement.

@malcdeacon7983

2 жыл бұрын

@@georgesworkshop8600 This is not the above Model TDWSF 83B EP UK . Belt Removal totally different.

@theoddjobcentre6686

2 жыл бұрын

@@georgesworkshop8600 my hotpoint h3d91wbuk is making a horrible sound it's unbearable

@user-qe2dg5wn3x

9 ай бұрын

@@malcdeacon7983 did you find a video as I am having the same issue need to replace the belt