Almost 10 years old and still one of the best videos on this subject that I found on KZread - thanks.

Been searching and watching then searching and this video is no BS right to the point w/ product and tool info. Wish I found this an hour ago. Now I can share with my boys to see what type of work we'll be doing this spring. Excellent video. Thanks so much.

I’m painting my house for the first time. I never heard of peel bond so your video was very helpful.

Very clear presentation with just the right amount of detail. Glad to see you recommend actual product names so's I know what to buy.

Lots of great tips! Like feathering w 7"sanding pad. Thank you!

Great video. Do It Yourself (DIY) is fraught with fear and insecurity when you take on a task that you have never done before. Videos such as this one helps to quiet the fear and uncertainty in a DIY project.

Well done. This was exactly the information I was looking for. Clearly communicated. I have been having a difficult time finding a product like Peel Bond.

Fantastic prep work. You guys did a really good job painting too.

Best house paint video. Thank you!

thanks for the video mate, looking to do a DIY job on my own place, and this is a great quick breakdown. cheers

Great video. Time for the good apples to stand up & make the bad apples look for what they are. Thank God for KZread and those who work with integrity. Make more videos with great tips guys.

Great finish work!

Excellent tips thanks, subbed!

Your content is superb. Especially checking with the manufacturer

Super helpful thank you!

Nice job!Thanks

Great Video!!

thanks for the tip about the lead!

Excellent explanation. Thank you

Nice work!

Great Video!! thanks

Thanks for the advice.

Thank you for sharing great information.

Great Job.

Excellent, clear and concise video. Thanks for making this Video 👍 Question : I want to remove the ingrained paint (take it back to original wood) from my wood beams that surround the exterior of my car port & porch. You mentioned the primer goes on milky but dries clear. Remembering I want to show original beams..Can I use the Prime RX to seal my beam and keep bugs from entering grain? FYI - Weather - I’m 👍in hot Sunny Florida! Ty

Thank You!

some good points,,, thanks

You are very good .

I always seal or prime before caulking to seal the surface. Caulk will shrink and not bond well to an unprimed or painted surface.

I have chipped exterior wood stairs that I would like to repaint. Any tips on prep and finish coat?

Thank you!

hey if the wood siding has tanin bleeding in some spots, would you recommend oil based primer instead of peel bond?

thanks for the video - does it not seem like overkill to use peel bond on entire house? Perhaps the siding was peeling more than my house where a quote I received said it would only be used on window frames that are badly peeling. This stuff is the bomb though according to all the vids and talk on the interwebs.

what kind of sander is best for 3 step facia? it is so tough to get it sanded and smooth on the face and underneath. u got any tips?

Just wondering, what areas you would Caulk for a project like this?

You read my mind. Yesterday I was asked to prep wood slates with a 4 inch orbital sander. Took forever and it was impossible to make the pint chip notch vanish or be sure that all the loose paint was removed.

what grit sandpaper do you use?

We need more workers like you in America. Most cut corners

@Cystus

6 жыл бұрын

Quality takes time, and time is money. Words most normal wage earning people don't wanna hear.

@bailey2624

5 жыл бұрын

thats cause people dont wish to pay the premium it cost to do work like this.

@bailey2624

5 жыл бұрын

i lose alot of work because I wont work for $1 sq foot for anything especially on the north east coast

@willfishing5605

3 жыл бұрын

Most? I bet you're a pain in the ass to work for

Is there a dust shroud you recommend? And does it work? I have the GV5000 and have a tongue and Groove wood house w/lead. I already have the HEPA vacuum from a previous part of the house(I used a paint shaver before but this part of the house is not that bad)...also trying out both Peel Bond and Peel Stop to see which works better. Also I was testing some MH ready patch for the peeled areas of paint, but if the peel bond fills then I will back of that..just testing one area for now...

For small corner cracks in old filler what method is best before painting?

Preparation takes time and doing what you did is perfect. Remember painting should take time too. Brush and roll is the way to do it for residential. You get more paint on the surface then spraying therefore will last longer.

My mom's house is peeling pretty badly. I have the option to use a powerwasher, but after doing my deck, and creating some divots and grooves, I'm thinking about buying an angle grinder with one of those nylon abrasive pads. Did you guys put down tarps? Thanks for the peel-bond tip.

When you are sanding and scraping non-lead based paint, is it bad if the paint chips get on the ground or should you put down some kind of cloth to catch them?

Have you ever painted a like color over brown? Wondering if the brown shows through even after the sanding and prep.

Do you do the same with x90 siding.Do you have to get all the oil based paint of before priming and can you use exterior paint with primer

Very good video

Hello! Just curious what Grit of sandpaper you have on your Disc Sander? thanks!

@Mike-qo4kp

6 ай бұрын

He is using a disk made for metal grinding. Comparable sand paper grit roughly 40-60 grit. If you sand wood siding with higher you will remove the wood grain.

The house we are buying has quite a bit of peeling paint. Do I need to sand down to the original wood? Or do I just need to get the peeling parts off before priming?

I'm sticking to Walmart brand paint it's cheap and I can charge the homeowner 1000s more than your average Joe been painting 50years and I'm still going strong thank you Philippines

Very good vid. It would have been helpful to see a before and after pic taken from a little farther away from the house for perspective. Thanks.

Is that the makita gv5000? I have one...it has a black pad with it...ru saying just get some 7 inch sandpaper to remove flaking wood from my tongue and groove..do u know of a clean-strip pad for the makita that works?

Do you have to use peel seal on whole house or just areas you have sande

can you use a sprayer with the Sherwin Williams paint?

Have you used a paint eater at all? I see a fair amount of guys in my area using them. Just curious on your feedback.

Thank you

Hi what makita drill are you using?

Which pile roller did you use?

Hi, what do you use as wood filler when painting outside wood?

Good info

Can this be done in winter months? Maybe if its above freezing?

What brand of Scraper & Sander did you use? Also what grit of Sand Disc was used?

Does this primer work on log siding as well?

Can I send you some photos to see if my the wood paneling on my victorian is sustainable to be repainted.

What’s up with the short pressure washer handle and what type of tip you using? I am new to the painting business, having a little trouble estimating exterior paint jobs. Any tips with coming up with an accurate estimate would be greatly appreciated from one painter to another?!?!? 😀👍🏻

Did you lightly sand again before top coat? I want high longlasting colour shine. Oil based gloss or enamel ?

Do you have to prime the entire wall or only chipped areas?

What pressure washer tip where you sing ??

problem in my area is rusting nails. after 2 years or so, the nail head rust starts bleeding through. some use a zinc spray and some touch up before with oil based paint. none seem that effective. your solution???

5" disc sander with a 7" resin sanding disc was the perfect tool to prep my old siding. For the 7" resin discs, the hercules brand at HF where better and cheaper than the diablo brand.

💥 Great video thank you. 0:35 what model is that sander.?? 🤟🏼

wish I knew of an example of the 7" disks that you use. All I find have a 7/8 arbor hole and that is not easily used with the 1/2" arbor this sander is populated with.

Did you go over the area with a tac cloth before primer , or could you have skipped the primer all togather?

a very good video, thanks be to God and thank you. I have questions regarding the last few minutes of your commenting: 'we only had a couple layers of paint previously applied so the surface leveled out really well, results will vary depending on the thickness and buildup of previously applied paint': I dont understand this part: can you help? thank you in advance and God blesses you and people around you abundantly with Himself!

How you remove old texicoat from the exterior wood siding?

thanx for the excellent tips......preferably for the great primer product by sherwin williams!!

Top video

Really nice job. However, I've used Duration by Sherwin Williams and I find it fades badly in the sun and simply can't handle salt air. I've since switched to using either Old Village or Behr Ultra and have had vastly superior results here in New England on the coast where paint takes a beating year round. I can only imagine it would last that much longer in less harsh conditions. I don't typically like to rag on a product but after many fails by duration I rate it as junk paint at best.

@malcolmbaldwin5735

2 жыл бұрын

I've been so stoked on Behr Ultra the last 3 years . The duration is nice and thick but a waste of money

What grit sandpaper for THX cedar siding

what sander were you using?

I’m not sure if this was asked already but what’s the PSI of the pressure washer?

Does Peel Bond work on Ceder?

Would love to see a video on a siding where there is tongue-and-groove and varnished wood, not painted or stain

This is now 9 years old. I never heard of the primer that fills in/smooths the surface. I certainly wish I knew this before painting my house, and fence.

Can I use the disc sander in this video for paint removal on lightly textured engineered wood siding? What grit would I use?

@jerrybauer6736

6 жыл бұрын

maybe maybe a wagner paint eater...but even that may be too aggressive. I try not to sand those products and just scrape and peel bond

Can you add an antimicrobial/fungicide treatment when using Peel Bonding Primer? I am going to paint over my fascia (prep with sanding and TSP washing), but wanted to make sure no mildew comes back, as is currently showing in some areas. Otherwise, I was thinking of applying some sort of pre-treatment before primer, but most of the water-repellent preservatives I've seen out there want bare wood, and I don't want to completely take off all of this paint.

@jerrybauer6736

6 жыл бұрын

if you are doing trim that needs peel bond you can also use Rejuvenate from sherwin williams. It is peel bond and paintr in one. Trim is time consuming, so there is significant savings doing 2 coats of rejuvenate vs 1 peel bond and 2 of paint. Mildew will always come back eventually, especially if you live by trees. Spores come off them and seed new mold growth. Make sure to kill existing mildew prior to painting. TSP by itself won't kill mildew. All paints have built in mildew killers these days.

So do you have to seal and prime? I would like to do this to make a good quality job? But thing is how do i bring that up to a customer? It’s like asking them do you want to pay me cheap for a half fast job or pay me full for best quality work...

What color by Sherwin Williams did you use ?? We are painting our house this summer and I love that color !

@M_Ladd

5 жыл бұрын

Pink!

my question in the video the siding has lots of unevenness in the grains , due to age and unfavorable weather conditions, how much of this can be evened out to obtain a smooth surface without the imperfections in the grain , otherwise to me it looks like the siding was never repaired

Care to share the grit of sandpaper

Thank you for this video. I recently moved to CO from MN and purchased a home with wood siding that was badly weathered and needed painting and repair. The company did a terrible job and is trying to tell me it's as good as it gets. It's unacceptable and not an outcome they shared at onset. I wanted to see if better was possible and you helped me to see it was. If I was still in MN I would be a customer. Thanks!

@1lizloring346

Жыл бұрын

Horror story reference (videos of the work) kzread.info/dron/oaJJwfaXRsWVG0eCLezwCQ.html

can the 'peel bonding primer' be tinted with a dark color? I'm repainting over a red to a dark gray.. ty Joe

@okeefepainting1023

5 жыл бұрын

Yes, it can!

If the paint isn't so damaged is primer necessary?

Thank you, I must paint my house, but first sand chipping paint, I will try your method, thank u

What a great video! We are painting our house ourselves this time to save money as new homeowners. Can you tint the Peel Bond? Or should we go with a paint that is primer + color in one? The reason I ask is our house is currently two colors. Bottom half = dark blue and the soffit, fascia, gables and eves are white. We are going with a light gray (steely gray by Sherwin Williams) for the house. Thanks in advance!

@sdmckeon4519

7 жыл бұрын

Yes, you can tint the peal bond but it cannot be returned if you tint.

Hey Connor, We just bought a house and want to paint the exterior. The whole house window frames and all are dark green. The house has all cedar shingles. What sander would you recommend and further more to paint a cedar home does the paint need to be rolled on our can it be sprayed on? Also what primer would you recommend for a cedar home would it be the same one you used in the video and if so can it be sprayed on? The home is 2000 sq. Feet so we want an efficient way to do the project but want it to look amazing. Thank you! First Time Home Buyer

@M_Ladd

5 жыл бұрын

Try Sherman William's store! This man is not a priest or try some painting contractors!

Was looking for deck restoration/ strip down tips and found one in that SW primer. Other comments mention how people don't want to pay for top notch work... NOT the case HERE ! I can not find anyone who wants to do anything labor intensive, be it the bums who cut my lawn that won't get off the machine to move a dog toy and will shred it or cut around ! OR a painter who claims a pressure wash and scrape is all I need and charge $1200 for a ground level 12 x 28 ' with no rails, just a 28' bench with no back, ONE coat sprayed ! No twisted or rotted boards, no complications just drunks or recovering addicts that want to spray easy condo's and newer construction. I'm a 58 yr old disabled and retired firefighter/ medic who worked construction since age 14 and 80+ hrs a week for 25 yrs and know nothing BUT physical labor and will pay extra for a skilled contractor who cares about his workmanship...GOOD LUCK FINDING ANYONE here in the working class areas of Ct. ! Don't know wtf happened but it's sad Any suggestions for stripping peeling latex other than breaking my already ruined back/ hips with a belt or disk sander ?

many thanks.. gig in Australia?

Nice job guys, very useful. As I need to prepare for painting a house just like this one, I am wondering what would be the result if I use ONLY a pressure washing (without sand mixed, just water) instead? The sanding by hand works great but it's a hard work for large areas to cover. Pressure washing must have be way more efficient method. Just wondering what the surface would be like, after the boards are dried out. Would it be ready for painting straight away or still need to scrap/sand or do something else?

@brewsterly2927

7 жыл бұрын

Pressure washing IS just water, sand blasting is a completely different process, mainly used on steel/metal. So many people are just lazy these days. Want shortcuts for every thing. I am 68 yo, pressure washed, scraped and sanding down flaky weatherboards now, half the big ol' house is done. He showed you what is required, there is no easy way, just do it.

hi, I really enjoyed your video and was wondering if you can can provide me with a little help as I am working up an estimate to paint a 30,000 sf hotel and it will need some smooth work as parts of the building are flaking . I'm in idaho and would truly grateful if you could provide me with some helpful info as far as pricing to paint and prep it thank you so much!

great job guys I would hire you guys but right now I'm search of getting hired