You know it’s going be a great day when you have a new video and a cup of coffee for breakfast.

Six years ago my Rheem air handler ecm fan motor stopped working. I determined the ecm fan module went bad - I assume it was from a voltage surge from a storm around that time. I was able to locate and purchase a new GE gentec module on eBay for $250 (the dealer flashed/programmed the replacement module for my specific system application). I did not purchase a new complete GE gentec ecm motor assy as at that time it was $700. The air handler fan motor w/the replacement fan control module is still working fine to this day. Properly diagnosing the module as the issue for fan not working was very difficult as all I had to go on was the wiring diagrams located on the air handler. At that time I didn't even know that an ecm fan assy that uses DC power to operate the fan motor was a thing. Had I had this video back then as an explanation of system operation it'd of saved me several hours of troubleshooting. Back then I couldn't find any info online on how the ecm fan motors worked or their elec/system diagnosis procedures.

@sprockkets

2 ай бұрын

Easy way to diagnose one vs the other. This may be somewhat out of date for newer ecm stuff. Try to turn the motor. If it feels stuck, unplug the module. If it turns freely, it's a bad module. If it still feels rough, replace all.

@josselindesir5409

Ай бұрын

Good job

I know you have the heart of a teacher, but you should CHARGE for all this knowledge. Case in point... you saved my son at least $300 plus in labor. He calls me up... 8 year old Bryant heat pump. Blower with an X13 would run all the time. Using one of your videos... I pulled the thermostat and it still ran. Checked G to C no voltage. Pulled the fan speed wires on the X13... still ran. Bad module. Replaced it with the Rescue Ez13 because it had both pigtails. All is well. i charged him a 12 pack of beer. 😁

@fudabi7850

Ай бұрын

He surely gets paid via KZread?

@70acrefirearms27

Ай бұрын

He does! Have you not seen his books?

I've literally diagnosed three bad ecm motors this past week! All three of the customers said they were running their furnaces on a generator (generac). Another great video, Craig! I appreciate what you do for this community!

@YTsux24-7

2 ай бұрын

Do they have surge protectors on the furnaces? I'd bet they do not.

@OhHenrysMusic

2 ай бұрын

@@YTsux24-7 Probably not.. There was a big power outage where I work and it messed up a lot of people's furnaces.

@YTsux24-7

2 ай бұрын

@OhHenrysMusic The inrush surge of the generator smoked the motor modules I'd bet. Upsell a surge protector any time a circuit board, variable speed, or ECM blower gets fried during power outages. This will protect their investment from future outage damage. P.S. thank you for your service.

@vieuxacadian9455

Ай бұрын

Is their genset certified to produce clean power ? older gen sets cant meet modern electronics HD requirements .

I always follow you, your videos are better than school and work place

@corruptedbrain6

2 ай бұрын

of course school wont teach you everything but i was fortunate enough to have good teachers. I learned the basics

As always I like your videos every day I work as residential PM technician and these videos are great resource to refresh my knowledge. Again as always your one the top technician and teacher…

This was perfect explanation and visual for new techs. Wish all videos was like that.

Great video, well explained, good camera quality and clear voice. Thanks always Craig, you teach and explain great.

Thanks again for all the content,editing,nd post s you create for us guys in the field . You are sooo correct the price of just the module is nuts , better to buy the whole assembly

Great video Craig. I bought your book on Mini-Splits. It’s been a huge help to me. Thanks for the knowledge

@acservicetechchannel

2 ай бұрын

Thank you for getting my book! I'm so glad you like them!

Excellent video, I recommend your videos to any of my friends who are interested in learning controls. It amazes me how how thorough your training is. I have gone to training that cost money that were not as good as your videos.

@acservicetechchannel

Ай бұрын

Thank you for sharing my videos!!

Thanks again Craig 👍Great work your like the MVT (Most Valuable Technician) of the Trade 😎

great information tech 🔥

Fantastic go video. As a Instructor,you always give me great ideas

@acservicetechchannel

2 ай бұрын

Glad to help

Great video. Very helpful

Another banger. 🤘⚡️🤘✨✨✨

Helpful video!

Awesome video 🙏 thank you so much 👍

Excelent. Enjoying your books

@acservicetechchannel

2 ай бұрын

Thank you for picking up our book!

When troubleshooting an ecm motor I like to also use the supco ecm tester as insurance.

Excellent! What would you do if you lost the programming on the red wire?

the best

Very niece sir ji ❤❤❤🇮🇳

Thank you for sharing your knowledge. I have a question, maybe a silly question. Does the board has a relay to turn on the gas valve?

Boa Noite estes modelos de placa são padrões pra todas as centrais ou cada uma tem seu modelo? Parabéns pelos vídeos sou daqui do Brasil acompanho seus videos

Thank you Craig, my question is if thermostat power up the G terminal when there is a call for heat, what speed fan would run and same question if there is a call for cool

I loved the Video and explanation! Question: I have 5 York units and I have Unit #2 switches from Cooling to fan only right after 5 minutes of running. Do you think that has to do with the module Program failure? Thanks

Hi so about the fonction of test in this board how it works or runs ? Thank you for All

I was struggling to understand how te controls work. Then I did a plc training (aka siemens logo programming 😅) and now I understand all electronic boards are basically logos without the coverage, with the difference that they are already programmed

sharing video to facebook.

If it’s an air handler here in the Pacific Northwest then you might see 256 volts at the blower in one neighborhood and 207 volts at a residential home a couple of blocks away… Ya our power grid is screwed up here

It's my job 🔧❄️There is no magic in it

I found this exact board and motor to be problematic. At least for me I’m constantly replacing either or in some cases both because of the blower taps not energizing or the motor not kicking on when being energized by the taps. Anyone else having this issue?

I see r and c connect not g

This ecm motor/module easily breaks as compared to older systems psc system..

Like craig Said. Fails at the Module. not the motor I know This for sure. Because I've Fixed.six ECM motor instead of replacing the module or the motor itself. On the high voltage side of the module There is a component on the board that is called a rush current limiter. This component, after a period of a few years blows a leg off the board. Due to heating of the component. $3 part from Melzer electronics out a Texas and you're up and running again. The latest one that I Fixed. Was Six years old and The rush current limiter blow a leg off the one side of the Component.. replaced with new one And still going 4 years now.

So confused