Just fixed my wife's dryer thanks to your videos! July 4 2023 🎆 Thanks!

Thank you! I followed your thermal fuse replacement video and it’s working again!

고마워요 덕분에 직접 수리를 했어요 Thank you, I did the repair myself. 바람세기와 온도조절버튼이 달려있는 케이스를 여는게 정말 힘드네요. It's really hard to open the case with the wind speed and temperature control buttons. 하지만 당신의 영상 덕분에 수리를 해서 이젠 뜨거운바람이 나와요 But thanks to your video, I repaired it and now it blows hot air. 구독과 좋아요 했어요 Subscribed and liked 정말 고마워요 Thank you very much 😉

Do you know if it's possible to turn the handle around so the button are facing in your direction if you blow your own hair?

@ThriftyToolShed

3 ай бұрын

It can't be turned. Even though the outer handle could twist it's the inner main frame of the handle that the switch is mounted to that is permanently in place.

Hi, I did a board and heating coil replacement but now the motor blows the wrong way. Any advice?

@ThriftyToolShed

9 ай бұрын

Is this by chance an aftermarket Chinese version of the board and motor? If so it is probably a 3 wire motor and is a 3 phase BLDC motor. The direction can be reversed by swapping any 2 of the 3 wires going to the motor. Double check that the connector did not get plugged in backwards. If not, you may have to press in the locking tab on the wire end to remove the crimped ends from the JST connector to swap the wires around. Hope it helps!

Hi, my HD01 isn’t turning on at all, it shows no signs of life. What could be the problem? Any way I can do some troubleshooting and check what’s wrong? Thank you

@ThriftyToolShed

7 ай бұрын

I do have a repair video that may help and I also share a simple diagram for troubleshooting. Best of luck! kzread.info/dash/bejne/iqpnlLWroNSdpZM.htmlsi=xgnQsEkizmqwsb7M

Hi brother.. If I want to lower the wattage of the heating element, what should I do? Because the electrical installation in my house is only 450VA (220vac) Even then, the voltage often fluctuates As a result, my hair dryer will turn on and off when the heater is turned on. Please help me

@ThriftyToolShed

8 ай бұрын

It is no easy fix for that. It would be modifications to the board needed for that. The factory only gives 3 levels or settings. I have not had to do any of that, but it would be more work than its worth honestly.

@Yand27_ID

8 ай бұрын

@@ThriftyToolShed I think so.. But, Will using a voltage stabilizer function normally? Because the voltage in my house can drop to 180volt When the hair dryer is turned on, the voltage can drop directly to 150 volts

@ThriftyToolShed

8 ай бұрын

@@Yand27_ID Hard to say, but you mentioned you only have 450va supply and this is a 1800watt device. I would doubt you would get much of anything from it at that low of power supply.

@Yand27_ID

8 ай бұрын

@@ThriftyToolShed Do you have instagram? I want to ask more I want to send you pictures of a fake dyson hair dryer machine

@ThriftyToolShed

8 ай бұрын

I don't. I do have a Facebook group so people can post or ask questions as a community. "On The Bench" is the group.

I see 37 ohms on the moto pins, is the motor solid? and the device is heating, but the engine does not work and there are no button controls

@ThriftyToolShed

10 ай бұрын

I believe the motor should be around 7 ohms if I remember correctly.

@MsAxelfoly

10 ай бұрын

@@ThriftyToolShed I see exactly 37 ohms, there is a value like 900 in the diode stage at the (lks620) drain end of the buck converter integrated

@ThriftyToolShed

10 ай бұрын

@@MsAxelfoly I am just going by memory. The motor was around 7 ohms. Not sure about the driver circuit itself. I did not have an issue with that on my repair.

@MsAxelfoly

10 ай бұрын

@@ThriftyToolShed The processor was faulty, there was a short circuit in the capacitor on the lower PCB, it was fixed by removing the processor.thx

@ThriftyToolShed

10 ай бұрын

Man, I was hoping you were saying the cap was shorted causing the microcontroller to be faulted. Dang, hate that the micro itself was the problem. That has to be very rare for sure! Good fault finding!