Don't Clean throttle body before watching this/Cleaning cable controlled or Electrical Throttle body
Автокөліктер мен көлік құралдары
Throttle Body and Air-Intake Cleaner: amzn.to/2UcEXAF
In todays video i will show how to clean throttle body weather if its cable controlled or electrical
so Don't Clean throttle body before watching this, there are some things you should know before cleaning that way you don't damage your car and cost you more for repairing
Steps for gunk Cleaning cable controlled or Electrical Throttle body
---So for cleaning cable Controlled Throttle body, after i removed throttle body hose and spray CRC throttle cleaner with plate closed and then open the plate and spray the cleaner again, then wipe it with paper towel
after 5 minutes put the throttle hose back
--So for cleaning Electrical Throttle body, after removing throttle body hose, spray CRC throttle cleaner with plate closed and then put the key on (ON) position, ask someone to hold the gas paddle and spray the cleaner again, then wipe it with paper towel
release the gas paddle
after 5 minutes put the throttle hose back
🔔 Hit the bell next to Subscribe so you don't miss a video!
👨🏻💻 Watch my newest video: www.tubebuddy.com/quicknav/latest/UC2lUGn7VN0u3U_M4RSmjQHw
Follow my Instagrams so we can be best friends
-------------------------------------------
/ ali_mechh
/ alimechh
Like my facebook page:
-------------------------------------------
/ alimechusa
**If the video was helpful, remember to give it a "thumbs up" and subscribe and turn the notification bell on, so you dont miss any new videos
Gears I Use:
Canon EOS M50 Mirrorless: amzn.to/35BdSsU
DJI Ronin-SC - Camera Stabilizer: amzn.to/3wINHwm
Andoer 3-Wheels Wireless Remote Control Motorized Camera: amzn.to/3vDuf2D
Gopro Max 360: amzn.to/345NNTf
For contact
email address: ali.hoshyar89@gmail.com
Facebook account : ali.hoshyar....
Like Facebook page: / alimech-1296961967080160
Follow me
Instagram: ali_mechh
personal Instagram: alimechh
Пікірлер: 545
This method is good when throttle body is slightly dirty. But if it’s too dirty better to open it and then clean from inner side too. Secondly never spray directly on throttle body when it’s attached all the dirt goes into intake. Better to apply spray on clean cloth and the clean it. That’s how i clean electric throttle of my cars.
@frozenking9394
3 ай бұрын
Thks I Wuz wonder that
@scottykilmer3920
2 ай бұрын
Exactly if you know the engine is crapp it doesnt matter, but if you care about the health of your engine dont do it this way.
@RealLifeFinance
4 күн бұрын
I thought dame if bad dirty spray rag vs spraying gunk into system
To the point, no fishy glamour, no waste of time, simple and excellent information 🎉👍
@AliMECH
3 ай бұрын
I appreciate that!
You dont waste a minute of anyones time. Every video should be like this.
@AliMECH
2 жыл бұрын
Thanks, i like to give more information is a short time, become when ppl having a problem, they should see the solution immediately
@jenarorosado460
2 жыл бұрын
But also remember, experience makes the difference
@babarbka0005
2 жыл бұрын
😂
@mackmorris138
2 жыл бұрын
This is wrong way too do it
@tonyreyes9969
2 жыл бұрын
@@mackmorris138 how to do it correctly then, please explain, thanks.
If you came to the comments for the reviews , this a 100 stars review , no time wasted and both ways shown thanks
Thanks for sharing your video on cleaning throttle bodies. As a throttle body manufacturer, we appreciate your thorough steps for both cable-controlled and electronic throttle bodies. It's important to properly clean your throttle body to avoid damage to your car and expensive repairs. We'll be sure to recommend your video to our customers for proper maintenance.👍
@AliMECH
Жыл бұрын
Thanks, glad it was helpful and easy for understanding
@tee3294
Жыл бұрын
A friend cleaned my throttle bottle with thinners, my car has been revving and consuming so much fuel itself since then. I’m struggling to get a spare throttle bottle for Chevrolet
@InexplicableBill
8 ай бұрын
@@tee3294 Your friend may have sprayed way too much into the throttle body that it seeped into the electronic control panel on the side of it, causing damage. Very little cleaner is needed.
My dealership charges $89 for this service so watched this video and did it for a few pennies that the clear costs.
@AliMECH
2 жыл бұрын
Awesome, glad that my video saved you money
@wolfsden3812
Жыл бұрын
Mine wanted 159.00
@843idfa
Жыл бұрын
Yes it's worth that much if they're going to remove it and clean it properly, not just spray stuff into it.
@jamaalblack9076
Жыл бұрын
Plus there’s more involved than just spraying in the throttle body it’s a 3 part kit that includes something like sea forming
@daviddowns7552
Жыл бұрын
thank you for the good details on this. can you please tell me if ( super tech spray from walmart is ok for this? it says throttle body clean + it was the only type they had? ) thank you very much. )
Best throttle body cleaning video on YT. Only one I found describing how to safely and properly clean the electronic TB and neat tip with torque wrench.
I have a 2010 WV beetle with a 2.5 automatic. I noticed recently more hesitation while shifting. I followed your technique of using in my case a piece of wood to keep the throttle plate open. Its interesting how clean it looked from the outside, but after the seafoam spray it was like black ⚫️ tar coming from it. I felt resistance against the motor (buzzing noice) once I bumped the throttle plate. I was able to lightly brush the plate. After about 10 minutes of cleaning, i started the car up. Quicker starting, quieter idling, and consistently better shifting. Thats just from driving down my street. Thank you sir for your help. Eveything i needed was already home for some time so basically it was free maintenance.
You can in fact, open most electrical throttle body by hand, may want to check with your individual manufactuer but Hondas, Toyotas, Subarus all allow you to open the butterfly valve by hand, just don't over extend it and do a throttle body / idle relearn afterwards.
Thank you. Every LS400 Owner needs this lol
Excellent! Great camera work and step-by-step instructions. Thank you!
@AliMECH
Жыл бұрын
Thanks for watching
@gregroth4696
Жыл бұрын
@@AliMECH Take the throttle body off to clean! C’mon man.
@thomasbrogan9102
Жыл бұрын
Exactly
Had my throttle body off when I replaced the coolant bypass hose on my 2005 Tacoma and cleaned it I moved the throttle plate by hand very slowly and cleaned it no damage what so ever and that was 2 years ago still running great
@royquesada5295
Жыл бұрын
Most damage comes from cleaning throttle body while still connected electrically.
@1995dresser
Жыл бұрын
@@royquesada5295 Yep
@frozenking9394
3 ай бұрын
Thks 😮
@Zeek800
2 ай бұрын
You are right. Open the electronically activated throttle plate very slowly and gently. Don’t force anything. Spray the microfibre cloth not inside the throttle body and use one finger to carefully wipe.
Made sense, to the point,into target. Thank bro
@AliMECH
2 жыл бұрын
You are welcome, dont like to waste time 🙏🏻🙏🏻
@achmada9338
2 жыл бұрын
@@AliMECH true, keep up bro.
Good points! Today I cleaned my electrical throttle body with Gumout cleaner, my ignition is a push start and I don't have the option to leave it open the way you did with the long rod. Yes I did get the engine light, but after cleaning and spraying into the throttle body little at the time while revving the engine afterwards the Kia Niro accelerated like a champ, I almost could not feel it and small hills became easier to climb and I could feel the air going through very well with a roar. I also did have a 16OZ B12 Chemtrol cleaner for the fuel. Now I will be clearing the engine light soon.
@sumanravichandran9107
Жыл бұрын
What codes did you get on the check engine light? I have 2018 Camry and my throttle body is not opening on key accessory position. is there any other way or should I move it by hand?
@Luigi13
Жыл бұрын
@@sumanravichandran9107 The only way to open the throttle is by using a clean piece of wood or a hard plastic material to avoid scratching it . It is like a spring it will open and then spray the chemical a little at a time inbetween each spray when I rev the engine I close it by not touching it it goes back the way it is when you first start. And then rev it a little bit and spray gently again and again each time revving the engine at 2K RPM not to eceed 3K rpm. This was my experience towards the end I sprayed an 1/8 of a can and let it sit with the engine off, for about 45 minutes and took it for a drive. Drove for about 10-12 miles and it run beautifully? I have about 31.5K miles on my Kia Niro.
I like videos like this because I learned more here then at my work shop
@AliMECH
Жыл бұрын
Thanks for letting me know, glad it was helpful
Good video. Make sure to clean the Idle Air Control (IAC) valve while you’re in there. Same steps as shown but you’ll need brushes to scrub the housing, valve pintle, and spring.
I always remove the throttle when cleaning them. Maybe this is short cut but i want it cleaned well on thw other side too and not riak of having the dirt and grime going to the intake manifold.
@843idfa
Жыл бұрын
Exactly, those cheap youtube videos try to lure people into clicking liking and subscribing with cheap advice, and don't care what happens to people's cars. I had a ton of grime come out when I removed and cleaned mine.
@GametimeSlime
8 ай бұрын
Than you get check engine lights if you don’t relearn it
Kaka Ali your chanel is one of the most useful Kurdish Channels on the Web, thank you for all these informative videos you share with us.
@AliMECH
Жыл бұрын
Glad to hear that, and appreciate your support brother
A well taught video thanks I'm a female and I am going to try it now!
@AliMECH
4 ай бұрын
Thanks for watching
Bravo! Quick and to the point!
Excellent work very well! Car is running smoooooth! 2012 Forester with electric throttle.
@AliMECH
Жыл бұрын
Great to hear!
Also when you are done your car might be a little hard to start and when it does you might see smoke from your exhaust. It goes away pretty quickly depending on how much cleaner that you had used. I can only speak on the ones with the cable. If you have one that is really filthy it is better to remove it to give it a good cleaning. Old toothbrushes really make short work out of cleaning one and you can use a toothbrush even with the throttle body on the engine. Great source of information I must definitely hit the like and subscribe. Look forward to watching another one of your videos.
@brazyuniverse4221
Жыл бұрын
If using a toothbrush and some carbon falls in, is that okay?
A little add up: -if you won't let it to dry, car may be hard to start for the first time because of fumes of cleaner left in the intake -if you have modern throttle position sensor it may need some time for ECU to readjust after cleaning. So it will be good if you replace ECU fuse before start cleaning and put it back after you reassemble all the parts.
@Nytellem
2 жыл бұрын
Never heard anyone mention this other than removing the neg to battery. Does that work as well?
@vakhtangjokhadze2427
2 жыл бұрын
@@Nytellem Might help but then you won't be able to use gas pedal for opening the throttle body right?
@jamesj.litteriojr.433
Жыл бұрын
@@Nytellem Yes it does. I remove ECM1 and ECM2 fuses after I'm done for about 1 minute and then put them back in. I do this every time I modify my intake system...Now I got it just where I want it. So even when you are doing an intake system, throttle body spacer, exhaust, etc. It is always a good idea to reset the computer system this way. Plus it's easier than removing the battery terminal. Hope this helps.
@premiumc2282
Жыл бұрын
@@jamesj.litteriojr.433 where is this located in a Honda Accord 2011? Is it easy to disconnect and reconnect
@jamesj.litteriojr.433
Жыл бұрын
@@premiumc2282 I would look in the owners manual for fuses or fuse box at the back of the book. Once you locate it, then you can see how the layout is setup on your car and pick the ECM or ECU fuse/fuses. My Scion has 2 ECU fuses so I pulled them both after I cleaned the throttle body and waited one minute then put them back in to reset the computer everything was fine. Hope this helps.
Thank you for doing electrical throttle body. I was thinking o would have to remove throttle body.
Now that is a smart way to clean the throttle body. I've seen people doing it other ways and then have to relearn the throttle idle control. This was EXTREMELY informative.
@unnainconnu9098
Жыл бұрын
Depending on the car, it may be easy to relearn it, like turning on the ignition, waiting 60s and turning it off. If it is, that's easier than using something to keep the pedal down and avoiding any contact with the throttle.
@brazyuniverse4221
Жыл бұрын
For a Toyota, the idle relearn procedure is super easy
@codyprice0295
Жыл бұрын
The reason you relearn the body idle air control is because you removed the smut from the throttle body that is causing the plate to have to open more to run. Not because you manipulate the plate.
@toddh6234
6 ай бұрын
@@codyprice0295 There is a position sensor in those electronic versions. Manually moving them throws them out of sync or damages them.
@codyprice0295
6 ай бұрын
@@toddh6234 on what kind of vehicle? That’s a very generic statement
Good work. I like this video. It's quick and to the point. Good advice on the proper spray TB cleaner only. I think I can do this myself. My Autozone has the CRC brand cleaner. I will also clean the MAF Sensor with only CRC MAF Sensor spray cleaner.
@AliMECH
Жыл бұрын
Glad it was helpful!
Go to any Chevy parts dealer they sell stuff called top engine cleaner, it’s the best hands down. A couple drops of this on a microfiber rag and your throttle body and butterfly are golden. Also clean the IAC Valve and MAF Sensor while you are at it using Sensor Cleaner.
@1995dresser
Жыл бұрын
Seen some KZread videos using Sea foam and a toothbrush with Great results the Sea foam won't hurt the coated bushings on the throttle shaft
Muito bom!🥇
Straight up dont be putting your fingers in an ETB. Some have ice breaking cycles amd they WILL sever your fingers.
! WARNING ! Remove the throttle body completely to avoid damaging your intake manifold. Throttle body cleaner melts plastic on contact. At least in my engine, there is a plastic cylinder just behind the throttle body lining the intake manifold. If you spray cleaner into the body like this, it will get behind and onto that plastic and will melt the surface. This will make the surface of the cylinder rough and pock-marked, at the least. Furthermore, You won't be able to clean the inner throttle body behind the plate without removing the body. A lot of carbon builds up on the other side of the plate. If you want to see how quickly the cleaner melts plastic, just find a piece of plastic you don't care about damaging and squirt some on it. I dripped some onto a paper towel sitting on some plastic under my hood and it melted the plastic underneath, fusing the paper towel to the plastic in seconds.
Great video, you went straight to the point. Thanks a lot bro
@AliMECH
4 ай бұрын
Thanks for watching
Thank you for your useful tips!
@AliMECH
2 жыл бұрын
You are welcome, thanks for watching
Thank you so much. Direct to the point. :).
@AliMECH
Жыл бұрын
Thanks for watching
"No need to use too much of the cleaner." LOL love this video!
@AliMECH
Жыл бұрын
lol if you clean something always use more hahah, thanks
Thanks. Well done, bruh.
straight to the point vid. I've 07 crv and noticed when engine is idle and I press the gas pedal there's a second delay before it revs not sure what the issue is, or is it normal. Any ideas?
Wow! Fantastic video. Thank you.
@AliMECH
2 жыл бұрын
Appreciate that
Very informative. Thank you !🙂
@AliMECH
10 ай бұрын
Glad it was helpful!
On an electric powered throttle before any spraying of the cleaner disconnect the multiplug. No need for ignition to be on. Once multiplug taken off you can move the butterfly valve by hand but slowly. No problem.
@Fayis1341
2 жыл бұрын
Removing multi plug or removing -ve battery terminal , which one is better ?
@sydsnott5042
2 жыл бұрын
@@Fayis1341 the multiplug
@kimpliny
Жыл бұрын
@Aidan Bhuiyan I don't understand why my car 2015 Nissan Sentra S won't have the butterfly move/open when the car was in the accessory mode and the gas pedal was pressed down. Thank you in advance for any advice.
Excellent throttle body cleaning video!
@AliMECH
4 ай бұрын
Glad you liked it!
Good demo and info thank you… from England 🏴
@AliMECH
Жыл бұрын
Thanks for watching
@melraine919
Жыл бұрын
@@AliMECH You’re welcome 👍🏼 🏴
You're so informative and to the point. Subscribed.
@AliMECH
2 жыл бұрын
Thanks and welcome
Genius!!!!
Well done wonderful
Thank you your advice is good
Great video brotha! Thanks so much!!!
@AliMECH
11 ай бұрын
No problem 👍
Very nice thank you for the valuable information, greetings to you
@AliMECH
2 жыл бұрын
Glad it was helpful!
Love This Guy!!!!! Always learn something new!!!!!
@AliMECH
Жыл бұрын
Thanks James 🙏
@gratefuldale117
Жыл бұрын
The key on/ pedal push method was new to me! I removed mine fully on 2006 Tundra 4.7 and really carefully did open gently, as well as a few on engine cleanups. Seems no harm done, just a clean TB!
Thanks,properly made video!
@AliMECH
11 ай бұрын
Glad you liked it!
Thank you. Can we do the same way with honda odyssey 2008?
Thank you for sharing this
@AliMECH
2 жыл бұрын
You welcome 🙏🏻
Good video! I did it to my car and the engine light turned on and then after driving the car for a few minutes, it turned off by itself.
@AliMECH
2 жыл бұрын
Thanks, it's OK, maybe you didn't let it dry completely, that's why engine light came on, after driving, it got dry 🙏
Honda Accord euro 2009 2.0 R20A3 just cleaned out whilst ignition on position 2 and weight on gas peddle so butterfly is fully open/closed. After clean, disconnect battery for 15 mins, reconnect with all lights and radio off, go to ignition positon 2 for 2 seconds, then start car, run at 3000rpm for 5 mins or until fan kicks in, and throttle position relearn is all done, set ready to go. Idle rock steady and running sweet 👌😙. This teaches ECU the adjusted position of throttle after it has been cleaned
Yeah dont clean electric throttle bodies like this. What he showed can damage them plus can hurt you doing that that way. Just take the throttle body all the way off and run a throttle position reset when you hook it up. Most cars its easy and also improves responsiveness from the sensor reset.
2008 Nissan Altima 2.5 do I have to reprogram the throttle after cleaning it or remove the Hose?
thank you for video
👏🏼👏🏼 going to my car now.
Great video thank you so much 🇺🇸
@AliMECH
Жыл бұрын
Glad you enjoyed it
Brilliant video 👏
@AliMECH
Жыл бұрын
Thanks for watching
Thanks for great video. How do you reprogram electronic throttle body?
@kato2182
2 жыл бұрын
just let it idle for a few minutes or driving on the freeway from 40 mph raise and drop speed or cycle the key in the ignition a few times each car is different for me i just had to idle it for a few minutes
Great job bro 👏
@AliMECH
2 жыл бұрын
Thanks for watching
Fantastic! Thank you!
@AliMECH
5 ай бұрын
You're very welcome!
Hi Ali, I moved the throttle body by hand, I had not seen your video. How do i test it now?
Thanks sir
Excellent video thank you 🙏
@AliMECH
11 ай бұрын
You are very welcome
I used carb cleaner instead. Works.
If you have an electrical throttle body... can you just unplug the sensor to open the butterfly manually rather than having to press the gas pedal ?
Smart trick with torque wrench - this is true re: electronic controlled throttle bodies - they are electronically calibrated and very sensitive. Never force open with hand.
Nice video. Keep it going.
@AliMECH
2 жыл бұрын
Thanks for watching, I will 🙏🏻
Great vid, not drawn out, great advice. If you get a chance to try BG throttle body cleaner, LMK how you like it, I definitely prefer it.
@AliMECH
Жыл бұрын
Thanks! Will do!
Thank you for the video
@AliMECH
Ай бұрын
No problem
Well since MAF is BEFORE throttle, do you think that crc carb cleaner spraying directly to the throttle while engine running would help ungunk the valves?
hello do i need idle relearn in this toyota camry which has electric throttle body?
Excellent!!!
@AliMECH
2 жыл бұрын
Many thanks!
My mechanic said that Toyota electric throttle bodies can be manually opened very slowly without damaging the unit. Personally only have 148k miles on my Toyota but it's holding up
Very good
Amazing video!!! Good advice
@AliMECH
2 жыл бұрын
Thanks
@AliMECH
2 жыл бұрын
Thanks
Hi am having a corsa utitlity bakkie it take time to pickup and need pressure on accelerator pedal
Good video!
@AliMECH
2 жыл бұрын
Thanks for watching
Great video thank you
@AliMECH
5 ай бұрын
Glad it was helpful!
I was looking for this after ive looked at my throttle body and saw it is difficult to get it out from his position.. I'll not spray inside it tho. I'll just use a cloth soaked in liquid to wipped it off. Thanks, mate
@premiumc2282
Жыл бұрын
How did that go for you any improvements ?
Nice video. Thank you. What should be done if carb and choke cleaner were used instead of throttle body and intake cleaner?
@AliMECH
4 күн бұрын
No, carb cleaner and choke cleaner most of the times damage it
Thank you so much
@AliMECH
2 жыл бұрын
You're most welcome
very helpfull thankyou
@AliMECH
2 жыл бұрын
Thanks
On my 2011 Ford fusion hybrid, the air filter is a lifetime filter under the fender.
LOVE IT❤
Thanks bro!!!
@AliMECH
2 жыл бұрын
Any time
Good video. Did this a few times on my cable controlled Explorer & Mirage throttle bodies but did not use towel to clean residue. Never knew they made an electrical throttle body. Don't like that idea in case of an uncontrollable surge.
@AliMECH
2 жыл бұрын
Thanks for watching, most of modern cars these day comes with electronic throttle bodies
@theroyalone7588
Жыл бұрын
How do you know if it’s cabled controlled or electrical?
Superb video 👍
@AliMECH
2 жыл бұрын
Many many thanks
Is CRC throttle body cleaner any different than regular Gumout or all the other carb cleaners?
Great video
@AliMECH
Жыл бұрын
Glad you enjoyed it
in elctronic throttle body without accelertor cable , if L-N key screw which is hidden in glue type material is messed up with. how can we adjust it to orignal position? do we need to use multimeter to check voltage of sensors at idle and full open throttle? do you know any reference values or can ask any professional who knows the values or procedures? its toyota corolla 2010 model..
Nice video.
@AliMECH
Жыл бұрын
Thanks
thank you for good infomation video.🏁👈
@AliMECH
Жыл бұрын
Always welcome
Hello 👋 how’s it going I’ll appreciated if you could answer me about this question 🙋♂️ when I press the gas pedal my throttle does not open. Is a Hyundai Sonata 2016 2.4 thank you 🙏
Well made video...
@AliMECH
2 жыл бұрын
Thanks for watching
Thanks Bossy Because U Jus Learned Me SumTing New😍😍😍😍
@AliMECH
Жыл бұрын
Glad to hear it
@delroyjohnson36
Жыл бұрын
@@AliMECH Respect ✊
I would not inject in a throttle body like this with a VAG throttle bodies because because they break internally (circuit board) , but just wipe it with a cloth and clean the valve, it's best to completely disassemble the throttle for better results
Thank you sir 🇮🇳
@AliMECH
Жыл бұрын
no problem
Thank you
@AliMECH
Жыл бұрын
🙏