Hi Great vid. I have a normal key start generator and a smart controller MPPT150/100-TR. Could I link my generator to the controller using the V2 Autogen to automatically start my generator when my lithium batteries drop to the manufacturers low level recommendation?

@DCAutogen

4 жыл бұрын

Hi Pumpkin Eater. You surely can! Most importantly is also knowing when to stop the generator and the Victron can send the signal to the V2 for that.

We have used the kzread.infoUgkxOTeIs0vv4_9B5hsmnLsk9r930uDQLu_Y for probably 30 hours with our camper and it’s been great! The noise level is really only noticeable when running the AC and other appliances like the microwave, hair dryer, or coffee pot. It’s not huge like other ones and it has wheels so even at 90lbs, I can move it!

these are so awesome!

I think this is great product. I would love to see this product being assembled on the more common "inverter generators" of 1000 watts or 2000 watts size (that would be a selling point for me and I'm sure for a lot of people as well). As there are 3000 watts generator with remote switch already in the market but no remote controled smaller size generators. I searched everywhere for small generator with remote control but I didn't find any in the market except yours (some DIY videos in YT I have seen are too technical for my liking, also not as good of a solution, and I don't have time to go deep into electronics to solve this issue and do trial and error unfortunately, Im looking for an easy solution). I hope you make video demonstration of your product on 1000 or 2000 watts inverter generators. I have your channel on my notification list and your website on favorite but I'm hesitant to buy without demonstration video of this product on an inverter generator size 2000 watts or smaller. Such video will give us confidence on its exact configuration and operation step by step on inverter generators of the mensioned sizes. So no guess work needed or uncertainty.

@DCAutogen

4 жыл бұрын

Hello @Mansur. Our controllers can be fitted to any generator type or size. Although it must be equipped with an electric starter motor. If you are referring to small 1000watt inverter types with a pull rope start, then this(or any other product) will not be able to auto start the generator. It is not limited to Generators. The V2 AutoGen has also been fitted to petrol engine air compressors, petrol and diesel engine water pumps and other standalone engines. As long as it has a starter motor, the V2 AutoGen can auto start and stop the engine. With or without choke on petrol engines, fuel injected, LPG conversions or decompression levers on diesel engines. So rest assured, we have a solution! The V2 is also customisable according to the application. Can receive a trigger to auto start from an ATS on mains power loss, pressure switches, water level sensors, battery banks, solar charge controllers etc. The sky is the limit!

@JM-yx1lm

4 жыл бұрын

That's because small generators do not come with electric start.

@DCAutogen

4 жыл бұрын

@@JM-yx1lm You do realise that what you are asking for is a small generator with No electric starter to have a remote start option? The reasons why small inverter type Generators are Small, is because the manufacturer needed to create a product that is lighter, smaller and more compact. They designed it without a starter motor and lead acid starter battery for those reasons.

Very cool and I have cellular phone, android. But there is no grid in many places with internet so how can this connect unless it has a cell service subscribed in to the controller. Like those little security cameras, you must have cable or a mobile hot-spot which must be connected/activated for use. We know things dont just 'connect' to the internet without a sim card and subscription.

hI ALEXANDER NICE VIDEO. Question what generator do you have there. it seems to be a small one with electric start, I would like to know what it is.

Thanks for sharing. I have a MGC100 that i am trying to setup on my Champion 100110 but cannot figure out all the wiring yet. I have the crank (starter), b-, and b+ but cannot make sense of the other 3 wires needed. I currently made my own setup remotely in the garage to start the outdoor generator by duplicating the current onboard switch on the generator but want to use the MGC100 instead. Any thoughts? I think the EM Stop would be the one of the other three to stop the engine which leaves me with 2 remaining wires. The generator has a 6-pole combination switch that controls it all.

@earthenergyhex

10 ай бұрын

I have the MGC100 as well and couldnt get it to work. I switched to this and it works now. I think the MGC100 needs some relays added to it but the seller can't dumb the instructions down to my level. LOL

Very fabulastic

@DCAutogen

5 жыл бұрын

Thank you Raheem!

@ganeshk7971

4 жыл бұрын

Where is this product available

@DCAutogen

4 жыл бұрын

Hello. You may find our products at www.dcautogen.com

Hi mate.......I am chasing a unit to use as a 240 mains change over, with maybe output to turn on a contactor with 12v coil

@DCAutogen

4 жыл бұрын

Hello @ Carli Cameron. Send me an email sales@dcautogen.com Give me a brief understanding of what you require.

Hey Nick, if you have a wish list going on you can add Alexa thru the mobile phone...LOLOLOLOL

@DCAutogen

3 жыл бұрын

Hi NG... Never used Alexa before but can control the AutoGen via Google Assistant :)

Wonder if there is anyway to program this device to automatically start the generator if let’s say I was on my boat and we were running devices off the house/boat batteries and wanted the generator to only start when the voltage dropped to a certain level? Would be a cool feature, although I guess most folks would just be using the generator w devices plugged directly into the generator and would have it running the entire time.....

@DCAutogen

3 жыл бұрын

Hi CrazyMoFo. The V2 AutoGen controller already does that. It starts the generator when your battery bank falls below the user selected low battery voltage threshold within the app. You can view more details at www.dcautogen.com

@TreadTalk247

3 жыл бұрын

Nick Alexander thanks for the information , I visited your website and love it! I’ll be getting one this off season! Thanks again

Good day, I am in South Africa and this product is the best I have seen, but, is it available in South Africa? Also where is this APP available, as I checked on PlayStore and nothing?

@DCAutogen

4 жыл бұрын

Hello Mervin. We do ship worldwide. Sent many to South Africa so far. You may view and purchase our products at www.dcautogen.com Links to our AutoGen app are also available on our site. Keep in mind that the app can only be used with our products. There is a setup process when you install the controllers or generators as you need to scan the unique QR Code attached to device.

@mervingovender4908

4 жыл бұрын

@@DCAutogen Thanks for the info, I did also find the App in playstore.

Can tou add 120 volt senseing , ro cause the genset to start on service loss then tripa transfer switch after stable power from genset

@DCAutogen

5 жыл бұрын

Yes, we can do that for you. Done it many times for customers.

@Wc4rav

5 жыл бұрын

Cost?

@DCAutogen

5 жыл бұрын

No extra cost Malcolm. Same price as on our website www.dcautogen.com

How would this work in the middle of winter? My idea is to bolt a generator in the box of my pickup and run a cord to front so I can plug it in. Is it possible to come up with something that can program to run for 5 hrs then shut off?

@DCAutogen

Жыл бұрын

Hi. It can be done, just need to protect the controller from the elements. It's not waterproof! Timer is easy, we already have that available as a feature.

hi nick, i have a Honda EU30is Generator with a manual choke. which version do i need ?

@DCAutogen

5 жыл бұрын

Hello Sotiri. You will need the V2 AutoGen 12v with Choke Servo. Is there anything else I can assist you with?

this is awesome but how do you get past the back feeding of the gridline if hooking to a house that is on the grid?

@DCAutogen

3 жыл бұрын

Hello Thomas. Whenever running a backup generator if grid is down, you must use an Automatic Transfer Switch. This disconnects your distribution panel from main grid and generator feeds your distribution panel.

@Mr231499

3 жыл бұрын

Generator interlock kit is cheaper than a transfer switch

@855electrician5

2 жыл бұрын

Interlock kit.

does it have a maintenance feature where it can start the generator every month for maybe 10, 20, or 30 minutes?

@DCAutogen

5 жыл бұрын

Hello Johnny. Yes it does. You can select the days, time and the period to run for all within the app.

We have a pull start generator with an off switch, we use it to run a well on a lease property we have cattle on. It’s 30 miles one way from headquarters. We go down in the mornings Monday, Wednesday, Friday to feed and check cattle and to turn the generator on to fill up our overhead tank which feeds the water trough. After 8 hours we drive back down to turn the generator off. It’s not economical as you can imagine. Is there a way to put a timer off switch or a timer valve on the fuel line so that after 8-10 hours the generator will shut off?

@DCAutogen

2 жыл бұрын

Hello Travis, yes that is easily done with a 12v programmable digital timer. Set it for X amount of time to trigger. Some models have an onboard relay which will shutdown your generator. Fairly inexpensive. If your generator had an electric starter, then with an AutoGen controller, everything would have been automated to start and stop when needed.

I want to buy one of these, but I would like to hook up a portable inverter generator to my off-grid solar system on my bus to supplement energy in the summer for an a/c unit on low setting if possible. Do you know where I can find information for setting up a backup generator to solar batteries? There seems to be no information on this.

@DCAutogen

5 жыл бұрын

Hello Zack. It is possible to install on an inverter generator. You may also find mppt solar charge controllers that accept input from an AC generator to charge your battery bank. You can visit our website for more information on our products at www.dcautogen.com

Do you have a video for your V6 using an ATS switch? For example,, the ATS has a 12 volt DC built in it and yet the Generator has the 12 volt Battary and we just purchased the Solar charge. We just can't find it.

@DCAutogen

2 жыл бұрын

Sorry, don't understand what the questions are. You want to know if the V6 AutoGen can be triggered from an ATS? Yes, that's easily done.

Could it be used with a well pressure switch so it could start the generator when the pressure falls to 50psi and then kill it when the pressure reaches 80psi?

@DCAutogen

4 жыл бұрын

Hello. It can be done. Can I get a link to your pressure switch?

Hi will this work on a troy bilt xp7000 series generator and a growatt sfp 3000 24v system

@DCAutogen

Жыл бұрын

Hi. Looks pretty straightforward. If it has manual choke, you will also need our choke linear actuator. Check out the V6 AutoGen smart controller on our website www.dcautogen.com

Hi, I have a generator with a manual choke, purchased new 2 days ago. Still can't get passed my head how a manual choke can b operated digitally (aren't manual chokes off a cable), I want to also know could this unit be fitted to a compressor as well to remotely start it? Both are 12v both key start with a manual choke compressor is deisel and generator is petrol. Also can one of these handle the two unit or do I need one for ever unit? Do you have a place in Melbourne that can install?

@DCAutogen

3 жыл бұрын

Hello Morin. Servos or solenoids are needed to operate the manual choke. We provide a digital servo and bracket with our AutoGen controllers for this purpose. Visit our store dcautogen.com Yes, has been installed in the past on engine driven compressors. You need a controller on each engine unfortunately. We are not located in Melbourne, Australia anymore. But I can find someone for you to assist with installing if the need arises.

Brilliant, Where can I buy the kit?

@DCAutogen

4 жыл бұрын

Hello. You can purchase all of our products directly from our online store at www.dcautogen.com

Hi, I have a wen 3750 dual fuel generator and want to connect it to Schneider electric AGS, the generator is just a key. Would this help me connect the generator to the AGS?

@DCAutogen

2 жыл бұрын

Hi Tony. Yes, sure can! Check out the products on our online store.

Is there a controller like this to convert a portable electric start to a 2 wire standby startup? My solar controller accepts generator input and has a 2 wire signal to start the generator. But my portable doesn't have 2 wire compatibility.

@DCAutogen

Ай бұрын

Yes, check out our newest AutoGen X smart controller.

$300? that some sweet markup for a couple chips and relays.

@DCAutogen

4 жыл бұрын

The time and effort we spend with our clients pre and post sale for individual customization, by far surpasses the $300 price of our controller. Thanks ;)

@Z-Ack

4 жыл бұрын

Dude 300$ aint about shit when you look at about anything for a generator.. if you get a commercial stand alone is like 1-2 grand and has a bunch of features most people wont ever need to use or could use. If you go the auto start at the electric panel than by the time u get the transfer switch, breakers, sub feed to generator panel if not already but the transfer switch alone is pushing 300$.. I mean you probably own an iphone or samsung and spent close to a grand on it and its just a godamn phone..

@indruwin5311

3 жыл бұрын

You going to spend 1 monyh making mobile app for your phone xD I rather spend 300$

Can this be setup on a Kubota 2cyl diesel with 12 volt alternator. Alternator needs 12 volt, glow plug, starter, fuel shut off. Can a proximity sensor be used for crank rotation so controller knows if engine is running or not?

@DCAutogen

Жыл бұрын

The alternator produces 12v. This can provide the signal to controller to know that the engine is running.

Hi There. Just want to ask if where can i buy this auto start module...

@DCAutogen

6 жыл бұрын

Zandro Varquez please visit our website www.dcautogen.com for more info and prices.

will your kit be suitable for Böhmer-AG 3800KE - 3000w 8hp Petrol Generator - Electric Key Start

@DCAutogen

3 жыл бұрын

Hello. Yes, it is compatible, but you will also need our Choke servo to operate the servo during startup. Here is the link for your reference. dcautogen.com/product/v2-autogen-12v-controller/

How do I wire a relay to it to auto start the gen when the power drops the relay out. I see aux1,2,3 on it are those used for that?

@DCAutogen

5 жыл бұрын

Hello John Chase. Do you have one of our V2 controllers?

@johnchase7667

5 жыл бұрын

@@DCAutogen Looking to buy one and I am trying to understand how the controller receives a hardwire start signal. We have a couple of rural WAN towers that we need backup on and I want to make sure this will work for us as opposed to buying a 7kw generac standby.

@DCAutogen

5 жыл бұрын

@@johnchase7667 the V2 is programmable so we can customise it accordingly. We can set it to start when a signal is received.

@DCAutogen

5 жыл бұрын

The V2 monitors a battery bank, if the voltage falls below a set threshold it will start the generator. Example: If you apply a 12v signal to the monitoring pin #10 and #12 via your relay, when the relay cuts the connections and no longer feeds 12v to those pins, the V2 will start your generator. When V2 receives 12v again on #10 and #12, it will kill the engine.

@jrcxley

4 жыл бұрын

@@DCAutogen hi Nick. Love your videos mate. Bought a V2 AutoGen for my Honda EU is 3kw. Could you send me instructions on wiring to that. I got the choke servo too. My email is Jrcxley@gmail.com Cheers. John Crossley. P.S. I'm in The Gold Coast, Queensland.

Does this have a LOW BATTERY VOLTAGE auto generator start feature?

@DCAutogen

9 ай бұрын

Yes, you can adjust the low battery start setting within the app.

Just need to add engine RPM and engine temp and extra temp sensors for the generator shed temp while running and I’ll buy

@DCAutogen

3 жыл бұрын

These options can be added if you wish. We can add an rpm sensor and 1 temp sensor. Need to check if we can add a 2nd temp sensor.

Good day sir you said connect the three important wire 1st is the kill switch second is for starter relay and for the 3rd sir you didn’t mention it? What is the 3rd wire

@DCAutogen

4 жыл бұрын

3rd is connected to generators 12v AC coil which is used to recharge the starter battery and to provide 12v DC max 8amps to external devices.

@alfredcruz7028

4 жыл бұрын

Okay sir, thank you so much more power to your youtube channel

@DCAutogen

4 жыл бұрын

@@alfredcruz7028 you may view our products on our site www.dcautogen.com

What are you using for the choke circuit? Does that gen have some kinda electronic choke or did you rig up some solenoid to switch it on and off with the v2 signaling? Im going to have to design a circuit that will hold off the starting sequence for a few seconds while the "choke" presses on a propane priming button to fill the carb with propane in order to start.. no physical choking necessary, you just have to prime the system for 5 seconds then immediately hit the starter so the propane will continue to flow with vacuum. Which aitomatically shuts if the gen shuts off.. im guessing the 5v circuit on the v2 can be setup like this maybe or will i have to make a little timer circuit that will pop on if power goes out then tell the v2 to start sequence..??

@DCAutogen

Жыл бұрын

Hi. You can use our Choke Servo or Choke Linear Actuator. Both available on our online store. Do you have an AutoGen controller already? Send us an email with your requests so we can guide you. Some programming may need to be done for your controller.

hi i have diesel keystart water pump...which versio do i need?

@DCAutogen

3 жыл бұрын

Hello. You will need the 12v version dcautogen.com/product/v2-autogen-12v-controller/

Will this work with my growatt spf 6000t dvm and a harbor freight 9000watt generator?

@DCAutogen

3 жыл бұрын

Yes

Hey !! How does the controller know when to stop cranking? Thanks 🙏🏽

@DCAutogen

Жыл бұрын

Hi. It can take either of the 2 available user options within AutoGen app: Measured dc voltage of starter battery charging circuit or generator ac output.

@joelcherian1169

Жыл бұрын

@@DCAutogen Thanks !

No idea of this is still an active thread or not. I would like to run a predator 9500 inverter generator tied to a Sol Ark 15k, what's your thoughts on running the 2wire start out of the Sol Ark to run this controller?

@wadebrewer7212

Жыл бұрын

I think I figured it out. Looking at your V6....using the ac inputs and a NC relay, snagging a power source (have to figure out what the 2 wire circuit on Sol Ark requires) for the coil side....run any ac power to the contact sides of the relay then to your controller on the AC input. When the Sol Ark calls for generator, it would close its relay completing the circuit, activating the relay coil, opening the contacts on the relay. Your controller would see that break, then know to start up the generator. When the Sol Ark is satisfied....it opens its relay turning the relay back to NC....your controller now has AC...then knows to stop the gen set. If you see another way....or have a controller actually set up to support a 2 wire start from inverter...let me know, please.

@DCAutogen

Жыл бұрын

Hi Wade. The AC inputs L and N are used as a generator running signal. For 2 wire start function we use pin#12. Whenever this input senses +12vdc it will trigger an autostart and 0v will shutdown.

@wadebrewer7212

Жыл бұрын

@@DCAutogen nice! Thank you.

@jacquelineheaton2545

Жыл бұрын

sol ark has starter delay . you don't need no $$$$ controller . you can get away with 3 NC relay relays( they like $15 for 3 pack on amazon). its what I did for my sol ark with predator inverter. tested and works great

Hi , I purchased one of the V2 Auto Gen and can’t get it connected to the app. How can I get some support for my problem

@DCAutogen

3 жыл бұрын

You can talk with us through our website live chat service.

will the generator automatically shut down when batteries are at full charge?

@DCAutogen

3 ай бұрын

There are a few ways to approach this. If your inverter/charger has a programmable dry contact relay, this can be programmed to send a start and stop signal to AutoGen according to battery bank state of charge. If this is not available, you would need to add our DC current sensor which will calculate when to shutdown the generator by observing the tail current drop during the Absorbtion stage of charging. When current falls below a preset value, AutoGen controller will shutdown the generator. It does not calculate state of charge though.

I want basic connection to make an automatic start and stop device for eu30is generator.

@DCAutogen

3 жыл бұрын

Hello. Check out the V2 AutoGen 12v version on our online store dcautogen.com

Hello Can I use the ats system for electric motor?

@DCAutogen

3 жыл бұрын

Depending on the application, yes it can be used. Sends an email with your requirements at sales@dcautogen.com

@edmilsonnobre9391

3 жыл бұрын

@@DCAutogen alright, so I Will let my contact to! Phone +258840501169 Email address: edmilsonedmilsonnobre@gmail.com

Can this work on a generator that is using manual choke?

@DCAutogen

4 жыл бұрын

Hello Eze. Ofcourse! The V2 AutoGen controller uses a digital servo to open and close the Choke during startup. Here is a link of our V2 AutoGen controller. dcautogen.com/product/v2-autogen-12v-controller/

we are interested in installing a 100 amp hr 12V lithium battery in our travel trailer. Our plan is to use a small inverter generator with command start to maintain the battery and power appliances. The priority power draws are a 12V dc fridge that requires approximately 600W per day and the blower on our propane furnace. Lighting is all LED. The battery should service this load overnight and it would be desirable to have the generator to auto start to maintain the battery while we are away from the trailer. Will the controller integrate with the generator's factory command start and also allow me to manually start the generator when we need to power larger appliances such as our AC? Most campgrounds also only allow generators to operate from 10am-6pm so there would also need to be a way to prevent the generator from auto starting during this timeframe in some instances. Sorry if this post showed up twice.

@DCAutogen

Жыл бұрын

Sure. Best to go through the websites contact form. Send us the details of your generator.

How do you start it from the app if power goes out and there's no wifi signal available?

@DCAutogen

2 жыл бұрын

You can provide power for your wifi router from a UPS or have the AutoGen controller start your generator when grid power is not available.

how the box know that the engine star to run it self for stop the electric star motor???

@DCAutogen

5 жыл бұрын

Hello VENDINGMEXICO. This is sensed via the generators 12v output or charging coils.

Do you have something for Koel 15kva ! With modbus??

@DCAutogen

5 жыл бұрын

Hello Rahul. The V2 AutoGen is compatible with the Koel but its communication is via wifi. Not modbus.

@rahuldogra

5 жыл бұрын

No I am asking how to hook this up with the genset panel! Does it support modbus? Or how will it communicate

@DCAutogen

5 жыл бұрын

The V2 connects to starter motor relay for starting. It also connects to fuel relay or coil to kill the engine. Communication between V2 and mobile app is over the internet. V2 connects via wifi. To find more info on the V2 AutoGen please visit us at www.dcautogen.com

@rahuldogra

5 жыл бұрын

Can this shift the AFM settings to manual? Edit: AMF means automatic mains faliure / switch

@DCAutogen

5 жыл бұрын

@@rahuldogra If you only require a signal to be sent to the AMF to switch on or off, then yes it can be done via our app. Do you need to operate the generator remotely? If you also only need signals sent to the Koels panel for remote start and stop, this cam also be done.

Visit us at www.dcautogen.com for more info and prices.

Does this need wifi? How will it work when power is out?

@DCAutogen

3 жыл бұрын

No, it doesn't need WiFi to operate. It needs a 12v power supply. Therefore, by powering via your starter battery, it will operate when you Power goes out.

How do you control the manual choke

@mafosa8519

3 жыл бұрын

you would have to add a electric servo.

Where Can I get one of these! Out of Stock

@DCAutogen

Жыл бұрын

The V2 AutoGen is out of stock and no longer in production. It has been replaced by the V6 AutoGen smart controller available through our online store.

Wonder if its a monthly fee for the app..

@DCAutogen

2 жыл бұрын

No

Is this unit compatible with an HPS12000HE Winco Honda GX630 with Electric Start? Thanks!

@danjjr

4 жыл бұрын

and if so, what would I need? I'm assuming 12V controller and Choke Servo?

@DCAutogen

4 жыл бұрын

Hello danjjr. Yes, I believe there is a manual choke on that model, so you will need the choke servo with a V2 AutoGen 12v controller. Is it equipped with any safety cut off solenoids for the LPG?

@danjjr

4 жыл бұрын

@@DCAutogen Okay, thanks. Yes, the safety cut off is an additional accessory and I'm thinking about buying it: www.wincogen.com/product/low-pressure-fuel-solenoid/

@DCAutogen

4 жыл бұрын

Should have been added as a standard option in my opinion. Either way, the V2 AutoGen can be fitted easily. You may find our products here. www.dcautogen.com

@danjjr

4 жыл бұрын

Does this controller wire to the safety shut off or no?

Aap ki range kitne hai

I have very littlle wifi connection at my cabin. Will this still work?

@DCAutogen

3 ай бұрын

When you say little wifi, do you mean weak signal, slow speed, or data limitation per month?

@MacsVacs

3 ай бұрын

@@DCAutogen It is pretty much non existent.

@DCAutogen

3 ай бұрын

It can still operate without WiFi. All depends on how and when you want the generator to start and stop. Limitations of no WiFi is, no remote start or monitoring via AutoGen app.

@MacsVacs

3 ай бұрын

@@DCAutogen i just want generator to start and stop when the batteries need charged and are fully charged without me having to be there.

@DCAutogen

3 ай бұрын

Can be done.

Were can i buy one i am from south africa

@DCAutogen

Жыл бұрын

www.dcautogen.com

So if the electric is off how do you have internet

@txsilentknight

11 ай бұрын

Extremely simple...run it off a battery backup

This work on diesel generator ??

@DCAutogen

11 ай бұрын

Yes, it does.

@dannysuru

8 ай бұрын

and you dont need to worry about wiring in a choke and actuator!

How far can the generator self reduce?

@DCAutogen

3 жыл бұрын

Sorry, don't understand what you mean.

Can i get this item in Singapore?

@DCAutogen

3 күн бұрын

Www.dcautogen.com

I feel like this won’t work when power goes out. If power turns off then your WiFi will also, cutting off the command between the module and your app... if you can prove me wrong, I’ll buy one.

@DCAutogen

3 жыл бұрын

Hello Jake. The controller still operates in Auto mode even without an Internet connection. It can be programmed to start if monitoring a battery bank, if utility power goes down, if on a timer etc. WiFi is needed only to monitor, remote start and to update any user settings. Is there something else you would like to ask?

@DCAutogen

3 жыл бұрын

Another option is to keep your WiFi router on a UPS, if Power goes out, the router will still be active.

Directly sending a start signal without checking the status of generator can cause damage

@DCAutogen

2 жыл бұрын

That has been accounted for. The AutoGen controller will never engage the starter as it receives a running signal on one of its inputs. It always knows if it's running or not.

How do I know if this is compatible with my key electric start generator?

@DCAutogen

2 жыл бұрын

Hello J. It's compatible with any electric start generator. If your generator has a manual choke system, you will also need our choke servo. Depending on your generator wiring, you might need to use external 12v relays to complete the installation.

@jde2896

2 жыл бұрын

Does the wifi mean it's connected to an internet? Or independent wifi?

@DCAutogen

2 жыл бұрын

Connects through wifi to the cloud. Then you can access it from any location.

@jde2896

2 жыл бұрын

I'm sorry I'm quite confused. Is there an alternative for that? I am worried if internet is cut from a hurricane then I might not be able to gain access via wifi?

@DCAutogen

2 жыл бұрын

If Internet is down and you are not onsite, you won't have access to the generator via AutoGen app.

not a big fan of utilities that need an app to run... make it stand alone and i'm interested

@DCAutogen

4 жыл бұрын

Hello Jeff. The V2 AutoGen is an automatic generator start controller. If you don't need the use of the app for monitoring, or manually starting from a remote location, then don't use the app. You can just install it and forget it, let it do its thing :)

how do i buy i of v2autogen 4rv

@DCAutogen

2 жыл бұрын

Check out our online store www.dcautogen.com

okay great , but when the power goes out , so does the internet ........ so what happens when the internet drops ?

@educatedredneck3342

15 күн бұрын

Cell booster

@DCAutogen

15 күн бұрын

Run your router from a UPS

@educatedredneck3342

15 күн бұрын

@@DCAutogen if the physical lines for the internet are down you can’t get it even with power. A cell booster is best. Most cell towers have generators. Get a cell booster and drastically improve your cell service. It won’t be as fast as WiFi, but it’ll be possible

Hi Nick I'm trying to contact you but don't know how to get your email address. I'd like to know what parts are used and where to purchase everything. Thank you for your time and I look forward to your response.

@DCAutogen

5 жыл бұрын

Hi Andre. You can find more info at www.dcautogen.com

How much is this device

@DCAutogen

Жыл бұрын

www.dcautogen.com for more info on our products.

Shut up, and take my money!!!

@DCAutogen

5 жыл бұрын

Thank you Darko for your enthusiastic comment! Your order will be prepared soon.

@neminon

5 жыл бұрын

@@DCAutogen you surely made superb product and it is precisely what I'm looking for. Thank you for your quick response.

Does it have a timer on it

@DCAutogen

3 жыл бұрын

Hello Leo. Yes it has a daily timer which you can set to start and stop. Also has run timers after the generator has started. All these can be set via AutoGen app.

@leohmong303

3 жыл бұрын

Thanks for the quick reply. Will it work without wifi? And will it work on my honda eu7000 is? If so please send link I need one

@leohmong303

3 жыл бұрын

@@DCAutogen I just need the timer to work, do I need wifi for that? Or will it work via Bluetooth

@DCAutogen

3 жыл бұрын

To run the daily timers, it will need an Internet connection via WiFi. Yes, it is compatible with the Honda EU7000

@DCAutogen

3 жыл бұрын

No Bluetooth connectivity. You can view our products here www.dcautogen.com for more information.

Great system but it's double the price of my generator can't afford that

@DCAutogen

3 жыл бұрын

Hello Emiel. Can't help with that unfortunately.

Is the app owned by yall?

@DCAutogen

5 жыл бұрын

Yes we supply the app with username and password with the purchase of our V2 or V4 AutoGen generators or controllers.

@6969smurfy

5 жыл бұрын

YOU had me. Until you said internet!!!!!!!!!!!! Why!!!!!!!!!!!!

@DCAutogen

4 жыл бұрын

Hello Dan. The app and controller need an internet connection to operate or monitor the generator from any location. Their is no other way unfortunately. But the AutoGen can still operate in Auto Mode without internet. It will monitor battery bank level or loss of grid power and start the generator. Hope this helps.

If there is not power is not internet

@DCAutogen

Жыл бұрын

Some essential things can always be powered by a backup system. UPS can provide power to small loads. Some modems/routers can be powered by 12v. There is always a solution...

This work without wifi when there’s no power

@DCAutogen

3 жыл бұрын

Yes, it works without WiFi. Although there are ways to keep your WiFi connection even when power is no longer available.

I need to start and stop a generator 900 miles away. A little WiFi probably isn't going to help.

@DCAutogen

9 ай бұрын

If wifi internet or GSM service is available at generator site, then distance doesn't matter.

apna address Din

It’s not “earth”… it’s negative you dope!