I love watching these videos 📹

@MechNinja

Жыл бұрын

Thankyou so much 😊😊😊 Don't forget to subscribe 😊😊😊

Maybe you want to look into some nozzle designs that could increase the thrust?

@MechNinja

4 ай бұрын

Please check my new videos....i have improved my design a lot. And thankyou for watching and don't forget to subscribe 😊😊😊

What about testing with the same rpm. To see efficiency of the blade. Not motor. 😂😂😂

@MechNinja

21 күн бұрын

It is impossible to do calculation in reverse.

This video would be better without the background music. Or, turn the background music down to 10% of what you have it at. Otherwise, it's really great content.

@MechNinja

Жыл бұрын

Thankyou so much sir for your response....from next time you won't hear it....😊😊

@JohnLauerGplus

Жыл бұрын

@@MechNinja And, I'm excited to see part 2!

@JohnLauerGplus

Жыл бұрын

I want to make a robot that drives around my backyard patio and pool area and blows the leaves off like a Roomba each morning. So I need a powerful fan on the robot. Your tests are helping me think through the design.

@MechNinja

Жыл бұрын

You must definately wait for my next video it has very high mass flow rate...... It will be uploaded within a week....😊😊

if only there was a duct where both motors could fit inside of, so a drone could use the benefits of both motors, the torque and the high speed rotation in one duct :D

@MechNinja

Жыл бұрын

Your question will be answered in my next video where I will use two propellers in one Duct. So thanks for watching the video and pls don't forget to subscribe so that you don't miss anything....😊😊

@TheTrumanZoo

Жыл бұрын

@@MechNinja im subscribed :D maybe later i can share a few designs that would love your 3d printed ducts :D

@MechNinja

Жыл бұрын

@@TheTrumanZoo yes definitely share me....and you can also suggest me some work too

@TheTrumanZoo

Жыл бұрын

@@MechNinja great channel man :)

Do you have one for 1400kV motor

@MechNinja

Ай бұрын

You can use 1400 kV motor it this design too

@hamzasellek894

Ай бұрын

@@MechNinja thank you 😌

700+ watts? How long will that motor last? Is there alot of heat in it after a 3 second pull?

@MechNinja

11 ай бұрын

I have not checked the motor lasting time....but yes after 30 sec of running it became hot.....

@MechNinja

11 ай бұрын

Thankyou for watching the video and don't forget to subscribe 😊😊😊😊

did you try the toroidal propeller?😅

@MechNinja

Жыл бұрын

Thankyou for your suggestion.... actually I am working on it....will upload the video soon.... don't forget to subscribe 😊😊😊

@herseem

8 ай бұрын

The point about a toroidal propellor is that it is effective as an alternative to fans that are in the wild, with an open tip. A duct already serves the purpose that the toroidal propellor was designed to fulfil, so a toroidal propellor in a duct is likely to be less effective than blades with a straight cut at the end

Fan propeller price and link???

@MechNinja

4 ай бұрын

It's in the description Or you can visit www.themechninja.com

from where i can download the 3d printable file for free

@MechNinja

5 ай бұрын

You can download the file from www.themechninja.com But it's not free 😅

Man you don't even let the thrust to stabilize for a second, you should give this things at least 3 or 5 seconds on full power to take measurement, your intention is good but your method need to improve or your data will not be reliable.

@MechNinja

10 ай бұрын

Thankyou so much for your suggestion.... actually in my new videos I am also verifying the operating temperature....and finding new ways to accurately measure data.... Do check my new videos too.... Thankyou so much for watching and don't forget to subscribe to subscribe 😊😊😊😊😊

What about the effect of gravity considering your test rig

@MechNinja

Жыл бұрын

I have calculated the ideal thrust while lifting the EDF to horizontal position...hence the effect of the gravity is considered here...if you have any doubt then you can ask me here.... And thankyou for watching and don't forget to subscribe 😊😊😊😊

isn't this the same video as last time?

@MechNinja

Жыл бұрын

Yes.. actually a little information was missing from it... So i have to reupload it coz I don't anyone to miss anything. Thankyou so much for watching it....

Price

@MechNinja

Жыл бұрын

You can check the website provided in the description

@naturalyhillsview9763

Жыл бұрын

@@MechNinja stl file ka price ya print edf ka h

@MechNinja

Жыл бұрын

Vo file ka price h....apko agr Print chahiye to apna address mail krdo me quote send kr dunga apko

I buy edf

@MechNinja

Жыл бұрын

Thankyou so much....you can check the link provided in the description

@naturalyhillsview9763

Жыл бұрын

@@MechNinja description m stl file h bro. Print edf price

first comment

@MechNinja

Жыл бұрын

Thankyou so much for watching it....😊😊

@Allrounder77860

Жыл бұрын

Goog