Not only does he sell 'Bimmers', but fixes them too. Great content!

when you performed the rear 325i caliper upgrade, did you have to do any special work to make the emergency brake work or does it work properly with the upgrade?

@DenverCoutu

9 ай бұрын

When you do E46 325i brake the E-brakes need no modification.

Can i do the e46 330 front breaks and m3 master cylinder only and just upgrade the rear to drilled and slotted e36 rotors or will i run into issues with the brake pedal??

@DenverCoutu

Жыл бұрын

to be honest i am not sure. I think that will change the brake bias from what i understand

Hello Denver, I just swapped 330i brakes onto the front of my e36 323is. I did indeed run into an issue. That issue being that after bleeding the fronts my pedal became even spongier than before when I ran standard e36 rotors and calipers. I've read a couple forums and some say you need a pressure bleeder, some say I need an m3 brake master cylinder. I noticed that you installed an m3 master cylinder but ran into issues with that. I was wondering if you were able to figure it out and which one you went with and from which store and also if you had any other tips I could use as my brake pedal goes so far down that I can no longer heel toe as well. Thank you!!

@DenverCoutu

Жыл бұрын

Hi Rahim, Thanks for watching my video. I have yet to install the M3 brake master cylinder. I found out there was a oem brake line(M10/M12 brake line Part# 34326755496) i needed to order because of the different fitting sizing but my brake pedal feel did not that different tbh. I plan to install the M3 master cyl this summer. I just bought the cheapest one i found from ebay. Did you only do the front or the rears as well? I did both. maybe that could be a difference. Maybe try bleeding again to make sure no air bubbles. I just did a normal bleed with my gf in the drivers seat pumping.

@rahimrustamov8241

Жыл бұрын

@@DenverCoutu Hello Denver, thank you for the response. I did indeed only do fronts but I am now going to be ordering e46 325i rear calipers and rotors. Are the brake lines that you ordered the ones that go to the master? Also when we bled the system we did the same thing where I was in drivers seat pumping and holding brakes down while a friend would bleed the system but the pedal would feel amazing with the car off but soon as we turned the car on it would be very spongy and mushy. I went for a drive and it brakes good but the engagement point is simply too far.

@DenverCoutu

Жыл бұрын

Yea that must be the master cylinder issue. it was just one brake line you need to go from the master cyl to the abs block

@pg190

Жыл бұрын

You need a bigger brake booster, preferably the e36 m3 one.

The rear discs on the E46 325i, I don't need to change the rear brake shoes on the E36 for those on the E46 325i, do the discs on the E46 325 fit on the E36 shoes? Thanks. 🤜⚔️🤛🏁🎱🇧🇷🇧🇷🇧🇷🎸👻

@DenverCoutu

6 ай бұрын

yes. this was it was easy bolt up. if you get e46 330i rear disks then the e36 shoes don't work

You replaced the brake master cylinder with the M3 E361995, does the E36 brake fluid reservoir fit in the M3 master cylinder or do I have to change it too? Thanks. 🤜⚔️🤛🏁🎱🇧🇷🇧🇷🎸👻

@DenverCoutu

6 ай бұрын

so i did end up installing the M3 master cylinder because the line size was different. the reservoir was the same tho

Your video and brake upgrade are very explanatory, what is the code for the front pad set for the E46 330i calipers? Thanks. 🤜⚔️🤛🏁🎱🇧🇷🇧🇷🇧🇷🎸👻

@DenverCoutu

6 ай бұрын

thank you. not sure what the code is for the pads.

what kind of wheels are those? they're sick!

@DenverCoutu

9 ай бұрын

Style 66

So the front brakes and rotors are from an e46 330i and the rear are from an e46 325i?

@DenverCoutu

Жыл бұрын

Yes! they bolt right on!

@frogking64

Жыл бұрын

@@DenverCoutu Thanks so much!

@csm101000

9 ай бұрын

Oh cool, so the calipers and discs are from e46 325i or just discs? Also are e46 330 and 325 discs the same size?

Did the solid transmission mounts a lot of NVH?

@DenverCoutu

10 ай бұрын

NVH?

@glenncattanach3073

10 ай бұрын

Noise Vibration Harshness

@DenverCoutu

10 ай бұрын

oh okay. so i did get a huge amount of NVH at first. I thought it was too much so i ordered REVshift transmission mounts. When installing i found that I actually had a snapped engine mount! so i ended up replacing the trans mounts at the same time to i did not have a true vibration test. Here is the video : kzread.info/dash/bejne/Y4unw8pvgs2edaw.html

@glenncattanach3073

10 ай бұрын

What color Rev Shift mounts did you get?

Was the brake master for e46 or e36 m3?

@DenverCoutu

7 ай бұрын

E36