I know this is a super long video...However, I figured these tips and tricks are skills that last a lifetime. Hopefully It helps someone, and if it is helpful, let me know. Thanks for the support and don't forget to share with your friends. Also, this was almost completely shot on my GoPro 8 . bit.ly/RRHero8

@spyder2016

4 жыл бұрын

RR Buildings love these kinds of vids.

@andrewdarbyshire9108

4 жыл бұрын

Always helpful as usual. I so want to build one of these on my property but having the funds always alludes me.

@petergrey1449

4 жыл бұрын

I highly recommend you checking out tirfors instead of chains/boomers.

@mezuumes4378

3 жыл бұрын

❤️❤️💯

@WhatsTheScoop123

Жыл бұрын

Can you sell me the Materials

It’s actually a very well written and comprehensive book kzread.infoUgkxhgbP-6hUnXu_QRaoHgLztgsI0YF3HqR0 . I wanted to pair this with an updated book on local codes to start planning a post-retirement dream shop. I think I have just about everything I need between the two. The extra plans available for purchase towards the end are priced almost as much as full home plans, not little sheds however.

I'm used to larger, corded routers kzread.infoUgkxfQ5_mgwq6PcudJvAH25t-I4D-3cTPz4z so this was a different experience for me. Basically, this is an incredibly sweet machine, fits well in the hand, etc. It has slightly less power than I'm used to, but that's understandable. Maneuvering freehand takes some practice. These days, it's especially nice to be able to avoid power cords. This is above the level of a hobbyist but below a pro level.

Man I appreciate you taking the time out to run us through this process. I have a homestead and build my own stuff...this is youtube gold. Thanks

Not too long a video at all as the teacher rocked the lesson and made it a breeze. One of your best i'd say.

@RRBuildings

4 жыл бұрын

Well thank you

When using the pythagorean theorem, the method I use allows me to avoid calculators and fractions of an inch. The triangle to find that 90 degree square is essentially 3x4x5. To get higher levels of accuracy with a large building, just multiply equally to all three and use those dimensions. Example would be to multiply the 3x4x5 numbers by 5 to give you 15x20x25. That way, you can use a 25’ tape measure and still get nice accurate measurements with large squares. No calculator needed and just as reliable.

Greg sliding down just made my day. hahaha!!!

Thx for the time, and skills your share. Hope you all had a nice Christmas and a sharp 20-20 to you all!

I always aim for the best, most accurate measurement It usually makes everything easier towards to end. Great job guys!

Kyle I have watched a multitude of pole Building Video's on You Tube. Your Buildings are Far & Above anything else that is available anywhere in the USA. You build the Rolls Royce of Pole buildings. I just wish I was younger so I could have one of your Builds but at 82 I'm too far gone. You are Truly the Master Builder Carl

@RRBuildings

4 жыл бұрын

Thanks Carl god bless

I am a metal roofer and a very good one at the least,but I am so grateful for your videos they are teaching me at 47 years old what true work ethic means! Great videos, please anytime you have the spare time,we all need these!

Rather watch an hour long video showing how things are done than listening to an hour of lecture in a classroom. Thank goodness for KZread! Edit: And thanks to you guys that take the time to video all this good stuff!

Thank you for all the videos that you film and put up. It takes a lot of time from your work. Very informative. Thanks you again.

I watch this video before bed every night to enjoy some goood framing. Thanks guys, makes me want to put my boots on!

Thanks fellas! I've learned alot from your vids. Just want to say thank you and I appreciate it! Keep up the fantastic work. Have a happy new year!

Man, straight out, you are awesome! Never have I seen a man in this world not related to me so helpful with detail! You are few and far in between... you are someone I would give the keys to my house, car, shed, four digit pin to my debit card... you name it- is how trustworthy you come across just by your resilient attention to detail and quality there of. I know your personality from experience and I can most definitely say you are a man of superior integrity and I know you won’t and can’t give a customer something that isn’t as perfect as you can possibly give them. You were born that way... I’m sure of it. Great job!.. and tell your men I appreciate them as well because I can only imagine how ecstatic your clients are to your finished product.

@RRBuildings

4 жыл бұрын

Thanks man that was a very appreciative comment and I truly do my best

@snowgo5922

4 жыл бұрын

RR Buildings... it shows, no doubt... it shows. 😄

I love your attention to detail and you do a great job explaining what you're doing, and why you're doing it- very informative. Your camera work and editing is excellent also. Keep the awesome videos coming.

Good to see you measure every sheet. One would think you could get the first sheet right, then "feel" the ridge, but one would be wrong and have a mess !

The way greg slides down is how i do it as well i been building carports with my old man for years now and it does make it easier to get from purlin to purlin and get to the bottom for another sheet. Glad to see im not the only one using that technique.

As a mechanical engineer I can appreciate the precision!

@jimmyhoffa310

3 жыл бұрын

Thank god they got a mechanical engineers appreciation, no one gives a shi* what you think..

@MikeMason1

3 жыл бұрын

@@jimmyhoffa310 Nice. Have a great day.

man I'm glad to know I'm not the only one with a boss who is obsessed with tiny little details that nobody will ever notice. (awesome video as always)

Kyle, I really hope the folks in and around your community know how blessed they are to have a builder like yourself. I've seen how sloppy builders can be and honestly, I would welcome your OCD my friend!!! 😀 👍Jay👍

@RRBuildings

4 жыл бұрын

Thanks jay

I like how Greg does those controlled slides down the roof. Obviously lots of practice.

@chess135

4 жыл бұрын

dident he say 4 build?

@hallenw

4 жыл бұрын

Fast learner

@mitchminard5859

4 жыл бұрын

He's marking the perlinsor he would walk down

another knot. loop around finger 3 or 4 times pull taught lock in opposite direction. will stay until you release it by giving it some slack by pulling tighter and keeping strings parallel. you can reuse string indefinitely. Awesome video Thank you !

Best video on KZread on how to square a roof!

Really enjoyed the extra step by step in this video. Keep it up!!!

Thanks guys for sharing so many tips, really appreciate, useful in our projects

Love the way you explain what you are doing.

So cool to see someone who REALLY REALLY knows what they are doing. Thanks for sharing your knowledge, strong work!!!

Thing a beauty. 👍 Happy New Year RR Buildings Kyle and Crew. (Greg & Zack)

If you don't mind this suggestion, yes, they're not exactly cheap but, ratchet binders. A little easier and quicker for you to make your adjustments. What you're also not taking into the mix here is, moisture will change your dimensions. That's just the nature of lumber. I know most would say "OCD" much, me, I say, you're just making sure everything is as exact as you can make it. This is why I really enjoy your channel, your "ocd" of precision. Keep the video's coming. Cheers :)

Absolute perfection! Thanks for sharing.

As a machinist I appreciate your precision!

Great video, I’d love to see a video of you explaining all of your lumber specs and spacing in a barn build... girts, purlins, posts, trusses, etc.

Cracking video once again. Happy new year to you and the team.

Thanks for these videos and stay safe.

Thanks for sharing your videos they’re great and good help for me

It’s so good that you dedicate time like this to educate people and consistently do it👍

Turn buckle style braces like you see used in concrete would cut time off of getting things leveled. We actually had some made with smaller threads that screw to any length dimensional lumber and that's what we use when leveling exterior walls on our buildings.

Another great informative video by a professional that takes pride in his work. I've been waiting for my contractor for going on 6 weeks he told me it'd be a week and a half. Go figure

@danmayes4657

Жыл бұрын

It might take forever to get in "The Zone" to make final adjustments. Maybe use both in-line. Get there then fine tune?

I fall asleep to these videos it's like construction ASMR or something ♥️

We use chains with 2 ton come alongs! Makes tiny adjustments easier. Great video

what impressed me most on this video is he avoided hitting his level on anything walking back and forth through chains and other obstacles.... unless that was edited out. 🤣

@zacharystrong

2 жыл бұрын

Prob a 500 dollar level I don’t blame him for being careful

@abhinsley

Жыл бұрын

I was cringing the whole time. I think that says more about me than it does anything else. 😁

@adamyoder8771

Жыл бұрын

No kidding!

Whatever amount of time spent on truing up the structure prior to laying your steel and roof is well worth it for sure - and thats the real lesson here. A half hour of tugging on chains and setting wedges will absolutely save more than that when it comes time to put down the steel since you wont need to make as many funny cuts to make things work out - great video love it!

@RRBuildings

4 жыл бұрын

Totally agree

Great video thanks 😊. I believe the knot you were demonstrating at 11:55 may be called the Marlinspike Hitch.

Nice work man love your channel. It's nice to know there are still guys that give a crap!🤘

I haven’t made it through the whole video yet but I’m wondering why you don’t use adjustable chain binders instead of the bear trap style? I would think they would allow you to adjust anything in very fine controllable increments. Love your content thanks for what you do

Love seeing the process!

As always dude great. Educational vidt

The amount of pride you obviously take in your work. Makes me want to be better.

Well now lets see, how many mistakes did i find.. I watched it all, and i half to say, ya'll were right on all the way. Most people just don't get it that close.. Thanks for Shearing , Texas

So impressed with this guy's skills. Not sure how old this guy is, but holy crap!!!

Really good job guys excellent description

Thank you again you've helped me tremendously !

Love your videos. Thank you.

When your running your sheets I see you’re matching your Lap rib or “good rib” I think you call it, then pulling out your tape and measuring your under lap rib or leading edge for your over hang number. You could eliminate that last step by marking your stack of sheets with a good marker on the leading edge at your desired over hang measurement. And then for remodel work when you can’t guarantee a perfectly straight eve snap a line at an arbitrary point and mark sheets to correspond to that that line. To each there own. I enjoy the vids 🤙🏼

@RRBuildings

4 жыл бұрын

I have thought about that for sure and honestly not sure why I haven’t yet

@nandothemantho6665

4 жыл бұрын

I agree with this. I put up metal frame buildings and once we square our roof I mark the lead edge with a marker or even a grinder to give the guys something to line up. Just a little easier, and if u do the saw cut the lap of the next sheet covers it up u can only see it on the bottom but the gutter will hide everything. Great video!

Buy a speed binder, it would be perfect instead of snap binder! You will love it, you can adjust it without unchaining!

wasnt long at all when we are learning great tips and how to do it the right way

Gonna used that technique for straightening my facia board on my garage build. Let you know how it goes, lol. Great video

ratchet strap truck tie-downs instead of chains for a finer adjustment when straightening might help - love the work

That was money. Love the old school work ethic and pride you take. Also quality workers who have the patience to learn from a master are rare. Thanks for the video.

you're a perfectionist ... not a bad attribute , however with the primary posts 'plumb' with your level , it may only be in or out within that length of your level , meaning the post could actually be bowed beyond your level's extension ... I always checked the top of the wall and checked plumb with a transit ... building racks to suspend drilling rig pipe in Angola in 1982 taught me that precise matters ... yes, it ain't rocket science but it sure does make a difference getting anything you build as accurate as possible ... spot on , budroe !!!

I have that same level. Love it... thanks for the video. 👌👍

@RRBuildings

4 жыл бұрын

it's a hefty price tag, but can you put a dollar amount on a lifelong tool that will make your more precise...probably saving you way more in the long run

Gotta get ratcheting chain binders for this!

Man good work I really look up to you

I really enjoy your videos and your attention to detail and of course accuracy...you are a craftsman... but i am a little surprised you havent adopted the metric measurement . I am a retired carpenter/contractor, when britain adopted metric 1965 I loved it.. it is so much easier and more accurate that imperial, yes there were a few moaners always are.... i do appreciate that your supplies maybe still be cut in imperial.

Happy new year

Happy New Year.❤️

7:00 "An eight of an inch in sixty four feet" sounds real good to me. Worrying about getting any more accuracy boarders on mental illness I would suggest.

Your videos are excellent. Glad you guys care about safety. Please reach out to your local rep. On some fall protection training. Your guy on the roof has two fall arrest devices used together. This is a big no no. In general dont ever hook two clips together, only clip to ring. Also make sure your SRL is rated for leading edge. Be safe out there.

34:19 - That's work flow at its best, no time wasted, one job straight to the next with no communication :-)

Like it. Thanks!

Great videos, thanks! Using a ratchet load binder might enable you to tension the chains in tiny increments rather than having to go a whole chain link.

You always have the best tips and tricks when it comes to pole barns. Thanks for taking the time to share your skillset.

Damn. I would assume most commercial companies aren’t getting it done like you. Great video

Man buddy great video!!! I love the little bit of prep work for making a project come out right like it's supposed to, it's that small attention to detail that keeps the project smooth and beautiful when you are done!!

@RRBuildings

4 жыл бұрын

thanks Bryan. Usually the difference between good and great is minimal. Most people just don't want to or don't know how to

Great job, I need to build me something like this, for my RV's.

Attention to detail👍🏽

Thank you

done with pride! yes Sir!

OCD, I love it. What a great pair we would be, an OCD builder and an OCD customer. That could be scary.

@chess135

4 жыл бұрын

i would say an expencive build.

Nice work. Are you available to come put up a building in ND. Lol. Thanks for the video.

Love seeing your attention to detail buddy. Showing the difference between a Pro and an amateur

One trick that i do sometimes is flush the stack of sheets and cut a little slit on the dog leg at what ever your overhang is. saves you from pulling a tape every sheet. Great work though guys! Keep it up!

@405diy3

4 жыл бұрын

When you install a new sheet, you already know your lap is at 1.5 then adjust your dog leg accordingly. Saves a little time. Maybe less than i think. But hope it helps!

@RRBuildings

4 жыл бұрын

Great idea

Nice work. Like 👍

The 2x4's are quick but i'm wondering if you benefit or considered using chain ratchet binder instead? Love your work, never done it but when i do, i'll be ready thanks ALL to you!

Thank you for all that you do. Great content and I truly appreciate your attention to detail.

I used to stick frame houses with an old carpenter down in Texas back in the 80 s and 90s we always used a story pole to level from bottom plate to top plate when plumbing walls . It didn't matter if it was 8' wall or a 12 ft wall

We use cabled tirfors which work really well. I find them easier then the chains just ratchet to tighten or loosen cables dont twist up as your ratcheting might be something to look into and try

I like your videos and they are very helpful. I have watched almost all your build videos and in your videos you explain why you use nails or screws in each application. Look up project farm he does a video were he compares different kinds of nails and different structure screws it really interesting I think you would like it

Nice.... you can tap the sheets together and put an inch and a half mark with a grinder that way you dont use your tape every time on the Eve . Very nice

It would be nice to see some drawings uploaded sometime that shows chain positions, wedges etc for moving walls in and out. Just easier for those of us who need a visual aid.

Greg pulls out tape measure Kyle: Hey, that's mine! Where'd you get that? Greg: Found it on a dead body... 😂

I love eating donuts in the trailer... so does Greg, with dead bodies who used to have 35’ tape measures. Lol. Keep up the banter! Nice work, great video, again.

@RRBuildings

4 жыл бұрын

Hahaha

@johnmoenster9995

4 жыл бұрын

Greg so should have turned the camera around and shook his head at the donut comment! :)

happy New Year

Mind you code is square within 1/4 in Indiana on a structure this guy is paying more attention than any contractor I’ve seen

Why not use a ratcheting chain binder for finer adjustments?

@RRBuildings

4 жыл бұрын

actually not as quick and a huge pain...I tried. It wants to spin the chain and is somewhat a pain....I wanted it to work better

@mesh1248

4 жыл бұрын

RR Buildings not sure if the new style ratcheting chain binders would help those they have a spot for an impact to hook on and tighten up instead of using the handle

@gerardchristensen2386

4 жыл бұрын

Mike Cabrey .. that’s what I was thinking

Excellent video just as are your other videos. I plan on raising a 42x48 next summer. Do you have any recommendations on chain size, lengths, quantities of lengths and the best place to source the requisite chains that won’t break the bank?

Assuming you set all of the post plumb in the beginning are you not taking them out of plumb as you make the adjustment with the kicker under the bottom chord of the truss simply trading a straight eve line for an out of plumb post?

@RRBuildings

4 жыл бұрын

Good question. We plumb all Columns during install yes... but as you noticed we were still off 1/8 to 1/4 max on our string line... when setting a column, even if the level reads good, you could still be off that 1/8”. Once we plumb our corners, the string line tells us how to make the rest perfect

So when you push and pull the building to get it perfect, and then you lock it down with the metal and screws, doesn't that cause tension on the screws holding the metal? I'm guessing the massive number of screws makes this point moot, but how does that tension affect the building over time? I would think it would cause oil canning in the metal, and when the sun hits it and it wants to expand this could cause even more tension.

@RRBuildings

4 жыл бұрын

Good question, but I can promise it’s not as much tension as you would think. Imagine your body without skin or muscle... bones will go every which way. Same with a building. We are merely installing the skin that creates the diaphragm strength we need to hold it all together

@chopperdropper752

4 жыл бұрын

High wind puts a tremendous amount of stress on a building like this with high wall long sides. If it holds up through the first big storm it's not going to budge.

@alumicomp

2 жыл бұрын

I have built a number of steel buildings and the small amount that was necessary to square this build was of no consequence..! I've had lumber warp several inches within several days before I could get back to the building and I used chains and ratchets to pull them back and the buildings still look great 10 years later..!