I always wondered what I would do if the end of my rod broke off trying to clean or pull a ball...now I know! Thanks for this!

Hi Mike! Thanks for showing us that the unexpected can (and does) happen to everybody at one time or another when it comes to muzzleloaders!

Thanks Mike you have given me so much information .You helped me pick out my first blank powder revolver ,an 1858 new model army . Can't wait to hunt with it. God bless and keep your powder dry.

That is a lovely looking rifle. And thanks for the knowledge.

EMPHASIS: Fully seat the obstruction against the powder after charging.

Mike I swear I learned something from you every video thank you for sharing that Joe the security guard from Oklahoma

Good helpful vid, you can now braze a copper penny over the hole and still use your cup.

@la_old_salt2241

3 жыл бұрын

That's an idea!

@nigelkavanagh2048

3 жыл бұрын

@@la_old_salt2241 👍had to do myself after shooting my dad's copper bucket as a lad. Saved my beacon!

@la_old_salt2241

3 жыл бұрын

@@nigelkavanagh2048 👍😉

@bwhog

3 жыл бұрын

That'd be one from about 1982 and earlier, before they started going to that crummy cupro-nickel sandwich and finally just copper plated zinc.

@nigelkavanagh2048

3 жыл бұрын

@@bwhog yea it's even before that they where non Magnetic.

Yes, the hole can be patched. Good video Mike!

Hey BIG MIKE! I thought you would have installed a "touch hole liner" in your barrel. Much easier to unscrew the liner & add powder than "pick it through" that small touch hole, as I'm sure you would agree!! This has to be your "shortest video" on record! And maybe MY "shortest comment" on my record too!!! "Gesundheit"!

I've had to do this with percussion guns. It's amazing how much energy that small amount of powder produces. Nice to this kind of video.

About 26 years ago I was cleaning my Pedersoli Brown Bess after a relaxing afternoon at the range. This was before I learned to stop using bore brushes in a smoothbore! I had attached a bore brush to the metal rammer and after reaching the breach was beginning to draw the rammer back towards the muzzle. That's when the 3 piece, friction fit rammer decided to come apart. The rammer came out but the brush, its adaptor, and the lower piece of the rammer had come completely off. I ended up getting it out by taking a 45-inch piece of fencing wire, bending a hook in one end that looked a lot like a shepherd's crook, pushed the hook through the bristles( not easily done) then retrieving the offending pieces. No harm, no foul, except now I had a nonfunctioning ramrod. I eventually found a machinist that produced a solid, once piece ramrod for me, complete with the threaded end. The button end actually looks more period correct than the one that came from the manufacturer. He said he made it in the same way that nail heads were made. I only use the new rammer to clean in the field. At home, I fashioned a wiping stick from a 5/8 inch oak dowel I bought. I carved an indention about a quarter inch up from the bottom of the "jag" end. I submerged it in a PVC pipe filled w/ boiled linseed oil & coal oil for a few weeks to waterproof it and prevent breakage. Now I only use moist pillow ticking to swab the bore. I still use that same wiping stick, and Bess and I are still together 26 years on, w/ many happy memories afield to look back on. Best regards, JA

@ericdee6802

3 жыл бұрын

Interesting, where do you purchase Coal Oil from?. Personally I like using Pine Tar mixed 50/50 with Turpentine, wipe it on the wood generously, let it soak overnight, then with a propane torch and a clean rag, heat the up so the pours soak in the pine tar, and wipe it clean, something my Father used to do with fence posts.

@SteveAubrey1762

3 жыл бұрын

Sry Eric, I'm used to calling it coal oil. It's kerosene. My grandfather was a WW1 vet, he walked a mail route for the USPS and owned a small farm. That's how he supported himself , my grandmother, my mum , my 5 uncle's& aunts and a neighbor who's wife died through the Great Depression & home front rationing of WW2. He told me the farmers used to fill a milk pail w/ sand then pour in a 50/50 mix of boiled linseed oil & coal oil( kerosene), then insert the wooden handles of their hand tools. Wood will still draw fluid up, that's why old dead trees rot. Kiln dried wood breaks b/c there is no sap to keep the cells of the wood supple. The linseed/ coal oil acts in that function preventing the tools from breaking as easily and essentially waterproofing them from the inside out. It preserves the wood cells. I wood is wood. I treat all my wood like this. Wood stocks get a few months soaking in a tub I made for that purpose. Wooden ramrods/ wiping sticks, tool handles, ect. Best regards JA

@ericdee6802

3 жыл бұрын

@@SteveAubrey1762 Hello Jack, thank you for the reply. Okay, Kerosene👍, My Grandfather was a WW1 Veteran as well, and my Father was a WW2 Naval veteran, My Dad had enlisted in 1933 and was a radio radar operator with the ZP-12 Squadron (lighter than Air) in the Atlantic, then He spend some time on the USS Arkansas(years unknown), then was deployed on the USS Redfin (Gato class sub) 1942/43 then finished off with the USS Wasp (essex class Aircraft carrier)1943/45 South Pacific theater. Don't know much about Grandfather, all I know is he was in France during WW1. Take care of yourself, thanks again for your time and response.🇺🇸✌️

@SteveAubrey1762

3 жыл бұрын

Hi Eric, that is so neat about your Grandfather & father. Do you have any pics , like a old photo book? My grandfather was an engine mechanic on airplanes in the Army Air Service, as it was called back then. I used to have lots of pictures he had taken , but after a few moved I can't find them. It's neat learning about ones family history. Very best regards, JA

@ericdee6802

3 жыл бұрын

@@SteveAubrey1762 Hello Jack, Unfortunately the only photos I have are a small handmade leather photo album My Father made while aboard the U.S.S. Arkansas and a bust portrait of my Father from 1938 ish, I had my Father's portrait tattooed on my upper left arm, like your senario with photos, many of my Fathers photos were lost in shuffles over the years, sad story. I love engines and Aircraft, those WW2 aircraft engines were state of the art back then, that would have been an interesting trade during that era. Well Jack, thank you for sharing your stories with me, it's always nice to speak with someone who can recant stories of themselves or Family members who have served during WW1 or WW2. Good health to you and your Family Jack.🇺🇸✌️

I had a steel ramrod tip come off a hardwood dowel inside my brand new Ron Luckenbill Bean style Tennesse mountain rifle because the glue failed. I paniced! When I calmed down, I ran hot water off the tip of the rod, managed to get the rod back in the tip, went outside and had a cold one and pulled the tip and the cleaning patch out of the barrel. I not only glued that tip but drilled a 1/16 hole and inserted a paneling nail and peened the ends. Lesson learned the hard way! Thanks for the video.

Great tip to know

Thank you Mike for another great topic this one on the Colt Walker: I appreciate your channel very much.😊

Its probably the easiest way to remove a jag or round ball. Been doing that for several years myself. Thanks for the demo...

Glad to know I'm not the only one that does it this way. I always fire into the dirt and never takes more than a couple of grains to do the job. Always find the jag in the first 3-5 inches of dirt.

Bout two weeks ago I got my cleaning rod stuck in my double barrel 12ga pistol but its an in-line that uses 209 primers so I just used the primer to fire the rod out. Worked great.

It's the little things that create a big mess lol. Great job on fixing it Mike.

I was a reenactor for around 15 years...we also did live fires at a range.. the trick we used to get a stuck ball (mini ball) out was a automotive grease gun.. a zerk fitting screws perfectly in the percussion hole on the Italian re-pos. A horrible mess to clean up but better than going to a Smith

Thanks Mike for another useful tip. I will put this one in my back pocket for sure and hopefully never need to use it

I was a long time civil war reenactor and was a weapons' and range officer for my PD so I ended up working on a ton of muskets. The problem you had was most common problem I saw. It is much easier to get powder into a percussion musket Sometime these guy had been live firing and there would be a skirt from a mini ball in the chamber. I was once hit in the leg at the 1988 Gettysburg event by a skirt but it had hit the ground first. Back before we were stopped from using ramrod I saw a ram rod stick in a limb at a small reenactment in Millersburg Ohio in about 78.

Good tip to show Mike . Shoot black powder enough and it will eventually happen to ya . Never broke a jag off , but i'll admit to a few dry ball loads . You usually realize it when your range rods about half way down the barrel , haha . Thanks for all the great vids .

Yep I’ve had to do that. About 40 years ago. I had a brass jag with the thread stem on it. I cleared it the same way. Then recycled those jags. Now I only make jags brass with a long steel set screw to thread into the rods.

This is a very helpful lesson. Thank you.

Great video. I learned something new today, thank you!

Mike sure does have a lot of nice looking guns.

Glad you cleared your barrel, sorry you lost your cool cup. Have a great day, and thanks for the videos keep them up.

Done that to deball a caplock. Sometimes you get excited and, well, forget a rather important step... In my case, the chamber appears to have eroded a bit and while I had a bullet puller that DID firmly grab the ball, I couldn't pull the ball and patch past that wide section and bring it out into the barrel. Unscrewed the nipple and put in about three or four grains of powder, all I could manage to shove in. It ended up being just enough to push the ball up about two inches which gave me more than enough space to let me get a good 20 grains behind it before re-seating and that was enough to blow the ball into the (very loose) river sand a few yards in front of me.

Have you ever tried one of those Universal CO2 Dischargers? I was sold on them when I used a friend's to clear a jag out of one of my rifles.

Thats a pretty good tip thanks mate

Thank you so much man that came in handy today you earned yourself a like and a subscriber!!

mike,,i had a homemade jag break off when i pushed a ball down on the main charge..and,,i fired it out ! no problems !, i will never use glue again to hold a jag on,,threads only !

Excellent. I've done the same one when I dry ball a rifle. I used my rammer to make sure the ball had exited. Beautiful rifle, BTW!

It is a little easier with a percussion rifle but not much. Try using an old wool sock to try and catch the jag next time. I don't know if I just got lucky but it worked for me. Enjoyed your presentation.

Had a dry ball happen with a .50 caliber t/c hawken where I almost seated it in the breech so I removed the nipple and put about 15 grains of powder in the breech and put the nipple back on and seated the ball on that 15 grains of powder and shot it out with no problem. It's easier with a percussion gun

Love that old gun

Been there... done that. Never drank from a creek before though!

good job brother 👍

good video Mike!

Good advice for what I hope will be a rare occurrence.

Good to Know Thanks Mike 😲😀

When I`ve done the same, I have shot the jag in to a pile of sand, easyer to retrive.

I had this happen to me with a .50 caliber T/C Hawken. Put some powder down through the flash hole where the cone/nipple screws in and reinstalled the cone/nipple and fired it into soft dirt. The jag end went three inches into the dirt. I cleaned it off and finished cleaning my rifle.

Thanks for sharing

Great tip👍👍👍👍

Thanks for the tip Mike. Bummer about the cup.

Was always curious to see what kind of power a light charge could manage, now I know.

You are the very best

Beautiful rifle....my 1st build was a Dickert style.

Thanks Mike. Keep a few tin cans around fir this next time. The best moor tante thing is to keep the obstruction, whether it is jag or ball seated on the powder charge. I guess you could still blow the barrel if it wasn't, even with a light charge.

I had the same issue a couple months ago. The range rod is fine after getting the threaded part out of the rod. Got the barrel cleared buy shooting it out but my gun is a caplock so it was a bit easier buy removing the clean out screw.

Thank you Mike. Good advice as always. By the way a cup like that can lead to drinking problems☺.

thanks for the info

Sorry bout your cup, good vid thanks

I’ve used compressed air w an accelerator nozzle through the nipple hole,percussion gun

Nice! Maybe using blank cartridges can help gets squibs out of barrels?

I did same thing for a 58cal Zouave replica. Of course much easier with removing nipple to put powder in. Wish I could get one cheap again, seems like they're much more expensive than modern guns now.

Excellent. Shoot lots and stay safe.

What about using a air pressure device? I have used one before. Next, I used a ball removal jag. A lot of work but it does work at times. If all else fails, I helped a buddy remove the breech plug and simply push it out.

I had this happen on my fowler. I ended up pulling the breech plug. I wish i knew this trick at the time.

I think I would've sacrificed the rifle sock over that lovely cup.

@duelist1954

3 жыл бұрын

I have more cups. I found a half dozen of them in a junk store for a very cheap price.

most important think to learn from this is push the obstruction down to powder after getting the powder in there.

Can I do this with an IGT airgun with a cloth stuck inside the barrel close to the exit? I mean shooting air without pellet. I'm afraid that the air pressure, if the cloth don't get out, may be too strong and damage the gun.

Rather than sacrifice a perfectly good copper cup, would you consider placing a block of wood 2-3 inches in front of the muzzle?

Why does this come up in my recommendeds... And why do I enjoy this kind of stuff?

Hi Mike! Great video. Was this a flat-bottomed breech? I've done this with a patent style breech, but wasn't sure if you could get enough powder between a patched roundball and a flat bottomed breech to shoot a stuck (dry balled) roundball out.

@duelist1954

3 жыл бұрын

I couldn’t get enough powder behind it to shoot the jag out the first time, but I moved it. That let me get enough powder in for a successful round two.

Great video, Mike! How many times has this happened to you?

@duelist1954

3 жыл бұрын

i can only remember one other time when a jag broke off

I still believe I have found something else to sacrifice other than my good copper drinking cup

Excellent I did it wrong great for right answer

Had to take the nipple off my percussion pistol and feed small amounts of powder through the rear reinstalled it made sure there was no gap between the patch and charge fired that thing out like a projectile never did find it. This is a particularly frustrating thing to have happen it disables your gun when all you wanted to do was maintain it or clean. Word to the wise the rod that comes with Lyman pistols has nothing keeping the end cap on except a bit of glue on one end.

With that cup you won't drink the creek empty ;)

Lol i’m sorry to laugh about your destroyed cup but i had no idea that the little bit of powder you were able to get in was capable of 1. Blowing the cup down range and 2. Blowing a .45 hole in the bottom of it hahahaha

Mike have you ever used pyrodex in flint lock? Maybe a video showing the good and the bad of its use Please, Thank you

@duelist1954

3 жыл бұрын

Sorry, but I have not used it.

a couple of months ago i had a nightmare! i was using damp patches in my 62cal jaeger. one of the shots sounded weak. like an idiot i loaded the rifle. the ball stuck half way down from gummed up wet half burned powder. it froze! i have a 3/8 steel rod with a large screw welded on the end and a T handle on the other. screwed it in the ball, it would not budge! i ended up putting a porta power against the T handle and the edge of the muzzle and jacking it out! i should have swabbed!

Ouch... I clear a dry ball the same way. Sorry Mike

Next video , soldering a patch in cup.

Alceehol is gonna get expensive, using that cup!

😊

Beautiful rifle. I have read stories of soldiers during the civil war being so close to being over run during the heat of battle they actually fired their ram rods because they didn't have time to remove it... Can your cup be repaired?

@KB4QAA

3 жыл бұрын

JH: Sure, he can solder a copper patch on it easily. Basic plumbing.

What if you have a wet barrel from cleaning? Will this still work, or would you have to resort to compressed air?

@duelist1954

3 жыл бұрын

It will still work

Been there, done that !!🤣🤣🤣🤣🤣🤣👍👍👍🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸

You did it yourself? Mitch wasn’t holding a gun to your head!

Yep, that's how ya do it but I'm sure some nervous nelly will be along saying how it's unsafe etc.

I currently have a patch stuck down my barrel. The jag itself came out but the patch stayed. What should I do?

@duelist1954

Жыл бұрын

Buy a patch worm from Track of the Wolf, and pull it out.

@gavindegust9170

Жыл бұрын

@@duelist1954 yes! As I wrote this earlier I answered my own question! Thank you for the reply! Your videos are Awesome!

I had a bad experience with black powder years ago but now i want to get back into it, i am looking for a custom percussion 32 but im having trouble im about to give up and just get a David pedersoli 32cal percussion do u have any advice

@NoahCline

3 жыл бұрын

The Tradition’s Crockett rifle is pretty nice for the money, and a little cheaper than the Pedersoli. I got it through Muzzleloaders.com as they had the best price (and free shipping at the time) compared to Dixie Gun Works and a few other stores. Ironically it was that gun that I had the same thing happen to but with undersized bore brush (pulled out of the base when trying to clean down in the recessed chamber). Didn’t even think to feed powder in through the drum to blow it out, but took the breach plug out to remove it. Mine shot low out of the box but was quickly remedied by filing the front sight down (couldn’t get either sight to budge in their respective dovetails so I just bent the rear edge of the blade to adjust the windage). Due to the smaller bore size, it did foul up pretty quickly so I had to swab it out after every shot or two.

@hbmoore7803

3 жыл бұрын

@@NoahCline i want a custom 32 at some point but to get my foot back in the black powder door im kinda leaning towards the Kentucky pedersoli, iv found some beautiful 32s but all n flintlock far as curly maple stalks

@NoahCline

3 жыл бұрын

I know Dixie Gun Works has some selection of Pedersolis. The Cub and Scout rifles come in both flint and percussion and a .32 option, as well as finished rifles and kits.

@peterrussell798

3 жыл бұрын

@@hbmoore7803 I’ve had the Pedersoli flinter in .32 for about 15 years. It’s the Pennsylvania model and I really enjoy it. I swab after every shot. .310 patched roundball, .015 patch, 25 grains Goex 3F with 2-3 squirts of 4F in pan. Of course today, the cleaning jag and a dry patch came off of the ram rod, which is why I’m here. Tried rethreading the ramrod onto the jag, but feels like threads are stripped. So on my next day off, I’ll be doing my best to shoot it out. I’ll sacrifice a tin can rather than a nice copper cup.

That's why I don't buy those all-brass jags. I've had one break, fortunately not inside the gun! I had dropped it, and didn't see where it was, and stepped on it. Broke clean in two! No thanks! I insist on steel threaded ones.

it happens

Just how I do it, lol

outfit made out of buckskin or linen?

I hate it when that happens!

Wow, who knew? When in doubt, add gunpowder.

Nice videos, but I wouldn't drink out of a creak ... microbes .

That rifle is definitely cursed. I'll take it off your hands.

Nice outfit

I got a jag stuck the whole way down against the breech plug face, no space for powder, now what ? When I removed the touch hole screw I could see the jag taking up all the space.

@duelist1954

3 жыл бұрын

Trickle in some 4F powder and replace the touch hole and fire the gun. It should move the jag at least a little. Remove the touch hole and check. Put in a decent powder charge, re-seat the jag on the powder, and shoot it out. If the first charge did not move the jag, remove the breech plug, and drive it out.

@jackson4861

3 жыл бұрын

@@duelist1954 breech plug is all one piece with the barrel , and I said jag but mean copper brush with a cleaning patch around it leaving no room for powder. Powder just lays on the outside of the patch

@jackson4861

3 жыл бұрын

@@duelist1954 the brush broke off when I drove it down the barrel with the ramrod, there seems to be something in front of the touchhole protruding from the inside of the barrel, almost like a ball stop in case you hadn’t put powder in. The brush got down in the through the smaller hole and stuck in the powder chamber just inside where the touch hole leads. And then it broke off.

@duelist1954

3 жыл бұрын

@@jackson4861 no breech plug is one piece with the barrel. If it looks like that, it is just well fitted. All breech plugs screw into the barrel.

@duelist1954

3 жыл бұрын

@@jackson4861 you are going to have to remove the breech. It will be tight. If you don’t feel comfortable doing it, find a gunsmith.

Great tutorial. I've seen advertised years ago that there is also a tool that is operated by a Pellet gun CO2 cartridge and was specifically designed for clearing out muzzleloader barrels, are you familiar with those?. By chance did you purchase your period correct Eye glasses through "Jas Townsend and Son" ( KZread 18th Century Cooking) located in Indiana?. Have a great day!🇺🇸✌️

@duelist1954

3 жыл бұрын

Yup. These glasses frames come from Townsend.

you blew it, blew it right outta there ;-) Maby you could do this with compresed air or aerosol like potato gun ?

@duelist1954

3 жыл бұрын

compressed air works fine, if you happen to have some with you in the woods

@KB4QAA

3 жыл бұрын

Linus: I had a stuck brush in my .54 cal Hawken. 100psi wouldn't budge it. The powder trick did it.

@linasmagnum

3 жыл бұрын

@@KB4QAA Good-grief, stuff happens, just pity the copper cup had to die.

@KB4QAA

3 жыл бұрын

@@linasmagnum Not dead. just needs a copper patch and solder. 5 minute plumbing job!

D

Hello Mike I'm a long time follower of your videos and I've learned a lot from you. I have a Facebook friend who owns an original Griswald and Gunnison revolver and is wanting to sell it but has no idea of its value. Can you give me an estimated value to tell him ? I'm trying to keep his name private. I'll contact him through Messenger.

@duelist1954

3 жыл бұрын

Griswold & Gunnison values vary quite a bit, depending on the condition of the gun, and the rarity of the variation. So, the best I can say is that his gun is likely to be worth somewhere between $10,000 and $30,000

I was afraid of backsplash towards you.