Good video, my only recommendation is replace the bushing & yoke also. As you could see the seal was already replaced, it went bad again because of a bad bushing/yoke/u joint, which cause vibrations.

@korndawggy1801

11 ай бұрын

Looked kinda like the rear differential had some leakage too. I was thinking one of the U-Joints might be bad or may have been at some point.

I just did this on my Astro. The seal was original and tight against the transmission housing. To remove the seal, I used a good brand new chisel and hammer to VERY carefully to go around the seal flange and separate it without damaging the transmission. After that I hit the flange with a screw driver to deform it slightly at one point in the old seal for removal. Worked perfectly and in a couple minutes it came right out. No damage or marks on transmission housing. For installation of the new seal, one of the cups in my ball joint press fits perfectly over the new seal.

Definitely made me feel confident about trying this myself

Thank You Sir, Your video & wisdom is very knowledgeable!

@WrenchingWithKenny

Жыл бұрын

You are most welcome. Keep wrenching 🔧

Thank you so much I’m gonna do this in the weekend so Helpful 🙌🙌🙌🙌🙌

Man, I don’t know if I could have ignored how bad those u-joints looked. But overall great video on how to replace driveshaft seal.

Thanks boss a Gare fix my truck tomorrow 👍👍👍

Good video without being overly wordy. Thank you.

boss man you make it seem so easy i hope this will work fot my 94 impala SS

@WrenchingWithKenny

Ай бұрын

It will. You've got this. Let me know how your repair goes. Keep wrenching 🔧

Thank you for that video.

I have a 2001 GMC 1500. Had the output shaft seal replaced. It is still leaking where the tailshaft and the seal meet. Not leaking from the rubber boot. I noticed that in the video you put grease on the inside of the seal and sealant on the outside. My mechanic did not put any sealant. Would that cause the leak? It is only a tiny drop. What kind of grease did you use? Trying to find your seal prep video. Thanks.

Keep them coming

Great video

Thank you Sr👍🏼

What did you pack the seal with sir?

I have seen the tail shaft it self let fluid leak out yoke some have a air hole for when you push them in it let’s air out

What about the leaking pinion seal ?

How much would you typically charge for this kind of job?

The rust pattern on the yoke can cause them not to fit correctly in other positions

What would be the cost of that seal replacement, you know from fair to high? TIA

Was the trans already empty?

dont know if youll see this or not but i was wondering if there is an underlying issue because my rear diff is leaking a bit too and so is my tailshaft thanks in advance!

@WrenchingWithKenny

Жыл бұрын

If the seals are constantly going bad, the tailshaft seal could be caused by either excess play from a worn tailshaft bushing or rust build up on the shafts yoke. Possibly even a worn yoke. The pinion seal in the rear axle could be from too little preload on the bearings or similarly , a rust or crud build up in the yoke that rides in the seal. I've on a rare occasion seen the yoke actually get a wear groove from the seal. Thanks for watching

what’s the part number?

If the OG seals were not packed with grease then why pack the new one with grease?🤔

I have a 92’ with a 91’ manual getrig HM290 transmission. Is it the same process?

@WrenchingWithKenny

Жыл бұрын

Send a photo to the Facebook page Wrenching with Kenny with a description of the information you're looking for. I will have Kenny look at the page tonight. Thanks - Meg aka Mrs Wrenching

Looks so easy...when you do it.

@WrenchingWithKenny

2 жыл бұрын

Lol . Thanks !! Been doing this for years !! Thanks for watching !!

What is the blue stuff? You packed the seal with. Thank you!

@WrenchingWithKenny

10 ай бұрын

Transmission assembly gel. Thanks for watching 🔧

@luissonoma6255

5 ай бұрын

@@WrenchingWithKennyYou’re welcome.

What grease did you use to pack the new seal?

How much would you expect to pay at a local garage to do this job?

@luissonoma6255

5 ай бұрын

$80-$130 an hour.

I need some help I have a 79 c10 and the tail shaft has play in it I think that’s ruining the seals. Is that play normal

What grease did he use ?

@Fish-dw5uw

9 ай бұрын

Transmission assembly gel

The shaft goes in about 1 inch then we feel resistence. Very strange. Seems to go in like that in 3-4 different locations on the driveshaft

Ahh yes, dont show the tool or how to use it. Thanks genius

@LJPMotorsports

Жыл бұрын

What tool? The seal puller? If he doesn't use one, and doesn't like to use one, why the hell would he show it's use? He's showing you how HE does it. You wanna know how to use the puller, check the top of the KZread page. There's a search bar there. Type in "how to use a tailshaft seal puller". Genius.

@efrainchavezii5257

Жыл бұрын

Right? I sat through this video to see the install tool and how to use it. He showed EVERYTHING but that.

Which seal did you use? And where did you get it?

@carportmods

10 ай бұрын

For future comment readers. Auto parts stores. Year, make and model specific.

@luissonoma6255

5 ай бұрын

I’d go with the brand National or Federal Mogul…