My similar model Poulan had a starting/running problem; would barely run. I tried cleaning/adjusting the carb using the $10 tool from Amazon, replaced the spark plug, squirted Seafoam DeepCreep into the air intake but it still would barely run, albeit better than before. Then removed the 2 screws that hold on the plastic cover over the muffler, then removed the 2 screws that hold on the muffler discharge plate, then cleaned the carbon out of the 4 tiny discharge holes in the plate that were partially plugged with carbon. It then started right up and now runs like a champ! If the tiny holes get plugged with carbon the blower either wont start or wont run well.

@Paisteboy

6 жыл бұрын

Thanks for sharing.

Helpful video... my leaf blower was doing the same as yours... cleaned the carburetor and replaced the air filter, but took it one step further... I replaced the 2 fuel lines and cleaned the gas filter. People sometimes don’t realize these blowers have a filter inside the gas tank. Once I did all that the blower run like new again.

@Paisteboy

Жыл бұрын

👍

Thanks for the help. I will be working on my carb soon.

@Paisteboy

8 жыл бұрын

Cool. good luck.

@couchrider6228

4 жыл бұрын

Joe Korpiewski headed to the shop to spray break cleaner in the carb. Better work

Excellent video, very helpful thanks

Hey Pasteboy, were you able to buy a tool to adjust the poulan carburetor? Did you find out if it was the diagram or just adjusting the carb to go full throttle?

Here's a helpful "MacGyver" trick I learned from another video, that you can use when you don't have the special adjustment tool. Take the plastic applicator tube off of something like a tube of silicon or glue, heat up the end and place it over the adjustment screw. It should form to the screw and hopefully give you enough torque to turn it.

@Paisteboy

Жыл бұрын

Thanks.

Use a dremel and cut slots in them to use a flat screw driver, high idle screw needs adjusted out

@stanburdick9708

4 жыл бұрын

exactly my thoughts.........no tool I have will fit in that needle adjust area, so Dremel is the only answer w/o buying a special tool

Another great video. Any end of the season garden videos planed. Keep up the good work.

@Paisteboy

9 жыл бұрын

Probably no end of season garden video. Most of the stuff is starting to die off. Getting ready to clean it up soon. Thanks for watching.

Hello awesome video I have the same one that I just got from garage sale.it does not work at all.i am going to follow you instructions to the letter.i need to change out the fuel lines also they discenerrating thanks

@Paisteboy

7 жыл бұрын

Good luck and thanks for watching.

@thomaswhetzell7485

7 жыл бұрын

Right on peace out have a good weekend

Clear. Thanks.

@Paisteboy

8 ай бұрын

You're welcome!

Thanks for the video, got my carb cleaned really easily. Is it normal that when I took the large hose off the carb no gas dripped out?

@Paisteboy

2 жыл бұрын

Not sure

That's just what mine did. Adjust the needles first. High speed is to lean. Also had to replace the fuel tubing. Major job on that one.

@Paisteboy

Жыл бұрын

👍

Thanks for posting! Had my fuel lines hooked up wrong and the primer / purge bulb wasn't pulling any fuel through the lines - whoops!

@Paisteboy

Жыл бұрын

Glad it helped.

Hey Paisteboy, Very helpful, HOWEVER.... I have cleaned and re-cleaned and cleaned again my leaf blower. I changed my spark plug. I still can't start the thing. It's a Murray - one year old. Is there hope? What am I missing? I am determined to fix this machine! Thanks!

@Paisteboy

8 жыл бұрын

A one-year-old blower shouldn't have any problems, but these days they do. You may need to buy a carb kit and rebuild the carb. I have another video rebuilding a leaf blower carb. kzread.info/dash/bejne/l6ObuJl9p7O6ntY.html check it out.

@nancyweatherhead4528

8 жыл бұрын

Thanks! I will try it tomorrow. I did get my weed eater to work!

Hi Paisteboy I was wondering if you ever found the problem with that craftsman leaf blower and how it only ran good on half choke I am having the same problem with the same blower.thanks

@Paisteboy

9 жыл бұрын

No. I didn't need the blower and never got the tool so I haven't looked at it since I made this video. This could also be a sign that it is starving for fuel. Check for cracks in the fuel lines at the gas tank.

@Bdoodee

6 жыл бұрын

I had the same issue. There are tiny orifices and venturis that a cursory topical spray of carb fluid won’t clear. I dissembled the carb completely and soaked it in line sol overnight. Rinsed everything in water and seafoam lubed for assembly. Put it back together and it runs like a top. Why pine sol you ask? An old mechanic taught me carb cleaner is too harsh for soaking. The bodies of the carburetors are a casting and dipped in a coating to seal the porosity. Extended exposure of the coating to carb cleaner drips this thin film off. When the coating is gone tiny amounts of air work into the mixture. This makes things lean, in some cases too lean. That’s why the need for extra choke/richness. Try the pine sol... I now swear by it for all my carbs that have sat too long. Hope this helps!

Which one of those two hose is the gas pickup ( small or larger) with the filter at the end? Having to replace all fuel lines and they just came apart and the carb I'm going to replace too. Get the tool at Amazon..... Got it done...figured out the gas lines...one thing u have to careful of is when u take out the needle valve and spring, always be sure the spring is straight and vertical when it goes back in. If not the unit will run but will stop.

@dennisvoelker664

4 жыл бұрын

Roy G small line is gas pick up

Because you are running half choke, you may need to replace the fuel filter. The filter may be half plugged.

@Paisteboy

Жыл бұрын

Thanks

Can you show how to replace the pull string on that model craftsman blower thanks

@Paisteboy

Жыл бұрын

Don't have it anymore

Thanks. Forgot which hose went where and you helped me out. Just ordered a new carb via Amazon $21

@Paisteboy

4 ай бұрын

YW

Dude your the man thanks so much

@Paisteboy

5 ай бұрын

Thanks for watching.

I took one apart a few days is all when you get in and cleaned it out real good soak it two or three times cleaned it again still wouldn't run when I change that little stream in the inside of their little bitty round screen it ran with into three pools

@Paisteboy

3 жыл бұрын

Thanks for watching and commenting.

What does it mean if I have to continue to adjust the fuel mixture screws on a carburetor?

@BarneyGumbl3

4 жыл бұрын

Very late, but probably that it's getting less and less fuel, needing constant adjustment. Most likely clean the carb and fuel filter, and maybe replace the fuel lines

What model and make is your blower. It runs ok, and you seem to have done a good job.

@Paisteboy

2 жыл бұрын

Sorry, don't remember

Thank you thank you thank you!!! "The thicker tube goes on the upper" @ 09:00

@terrysmith7454

5 жыл бұрын

WHAT IF YOU REPLACED THE FUEL LINES BOTH ARE THE SAME , DO THE FILTER ONE GO ON THE TOP / RETURN LINE GO ON THE BOTTOM OF THE CARB

@Paisteboy

4 ай бұрын

👍

the metal screen at 2:40 can be removed and cleaned out, stuff gets past that screen too. clean the needle and seat also. if the blower ran fine before this, neaning hi and lo screws were correct then they should be fine afterwards. I would think about getting a carb kit if the adjustments don't work. Clean out the carbon in the muffler,spark arrestor.

@Paisteboy

19 күн бұрын

Thanks for the tips.

i'm having same problem after new carb install i have tool which one should i adjust and which one is high and low

@Paisteboy

3 жыл бұрын

Sorry. Not sure.

I just missed a few minutes you didn't show! HOW TO TAKE THE CARBURATOR OUT? That was the most important part.

@Paisteboy

2 жыл бұрын

👍

I love it... thanks

@Paisteboy

Жыл бұрын

You're welcome.

How many gaskets, and what position did they go in if you did have more than one each side.?

@Paisteboy

2 жыл бұрын

Sorry again. To long ago to remember.

Any sled videos soon? Love the vids keep them going.

@Paisteboy

9 жыл бұрын

Yeah. I have to put new scags on my skis for this season. I'll do it probably in a month f t on now. Thanks for watching.

Is there a tool for adjusting the the low and high mixture screws? I tried but couldn’t adjust it.

@Paisteboy

2 жыл бұрын

I believe there is there is a tool for that.

Is that a yamaha moto-bike at the end of your video behind you?

@Paisteboy

6 жыл бұрын

No. It's a 1980 Suzuki RM 60

Thank You.

@Paisteboy

3 жыл бұрын

You're welcome. Thanks for watching.

7:00 carb cleaner will mess up diaphragm, gaskets, and O-rings. Break cleaner won't damage them I've heard. Warm water is always good. Dry it well.

@Paisteboy

4 жыл бұрын

Good tip. Thanks for watching.

I believe it could be filter screen for the muffler

@Paisteboy

Жыл бұрын

That is a possibility. Thanks for the comment and for watching.

you should never use a drill of any sort to tighten down any bolts. your dealing with aluminum casting motor and many plastic parts. just a little advice

@kickenchicken9645

3 жыл бұрын

u set ur torch

just saying as a tip never spray any gasket/rubber parts of a carb it eats it up and distorts it but on the outherr hand im pretty sure you know :]. just a friendly small engine mechanic trying to help but great job tho. one more thing jut go on ebay for that tool they are pretty cheap

@Paisteboy

9 жыл бұрын

dragon124356 I kind of hinted that it may not be good for the gaskets, but gave them a little shot anyway. Hope I didn't damage them too much. I probably should just get a new carb kit for it anyway. Thanks for your comment and info about the tool.

@dragon124356

9 жыл бұрын

oh ok i see now but no problem

lost one of the screws that are with the primer bubble, what size, how to order?

@Paisteboy

3 жыл бұрын

I doubt the manufacturer sells one screw so I would suggest taking the a matching screw to a place like Fastenall that sells just screws and fasteners. They may be able to match it up for you.

I have the same blower (I also have a few videos up on it) I've owned mine since 2001 and let me tell you... It's been a lot of maintenance lately.. I've always ran good quality oils as well.. I will most likely keep my old Craftsman blower, even though it's been a headache at times.. But, I finally sucked it up, and spent the money, on a really nice high quality handheld blower.. Figure, I'll use it when I'm in need, and need one that's dependable.. I have way too much money into my Craftsman blower, to do anything with it but keep it.. (You'll see if you watch my videos) I purchased a Stihl Bg 86... I haven't even unboxed it yet.. Great video !

@Paisteboy

9 жыл бұрын

Vdubin64 Thanks. I have the blower attachment for my cub cadet string trimmer that I use. Sounds like your new blower is nice. I like Stihl. I have the FS90R string trimmer. It's a beast. I'll have to check out some of your videos.

Magnific 👍

@Paisteboy

2 жыл бұрын

Thanks. Glad you liked it.

What make of blower did it come from.?

@Paisteboy

2 жыл бұрын

Sorry, I don't remember. It was my brother's blower and he hasn't had it for years.

I need instructions on how to replace spring when reattaching baseplate cover to Craftsman 25cc gas leaf blower Model 358.794942

@Paisteboy

Жыл бұрын

Good luck

I personally think the carb is cleaner than the pan your trying to clean it in.good video though.

@Paisteboy

Жыл бұрын

👍

could u use brake cleaner instead of carb cleaner?

@Paisteboy

7 жыл бұрын

You could but I wouldn't recommend it. It can leave residue on the parts and is hard on rubber.

@dkupy100

7 жыл бұрын

Disagree... carb cleaner is much more agressive. I would not have sprayed the metering or pump diaphrams. And does BRAKE CLEANER leave a residue on rotors and drums? I don't think so. A carb rebuild kit under $10 could be had from eBay.

My grandpa had that blower before

I took the ink pen before I got him at Amazon and took the end out of the ink pen and heat it up a little bit and pushed it on those things and made me a little special tool

@Paisteboy

3 жыл бұрын

Nice hack!

Use a 14 gauge crushable wire connecto to adjust the high and low speed screws on the carb!

@Paisteboy

2 жыл бұрын

Sounds good.

@thomasplaisted3579

2 жыл бұрын

@@Paisteboy okay! Where are you from? I am in Ohio.

This is just me but I would have replaced the metering diaphragm and the primer bulb. Just check that the too flaps on the pump diaphragm are flat not bent up or down. I learned that from dony boy73 and home garage both are awsome small engine mechanics

@Paisteboy

2 жыл бұрын

Yeah. Probably a good idea.

hey where do you get your parts from thanks

@Paisteboy

7 жыл бұрын

Not sure. My brother ordered them online.

@thomaswhetzell7485

7 жыл бұрын

Hey can you find out for me please thanks a lot peace out happy easter

What carb is the number of this? My red throttle handle broke!!’ I am looking a replacement carb like this!!!!!

@Paisteboy

3 жыл бұрын

Sorry. Not sure.

Any chance you have the model number for that carb?

@Paisteboy

4 жыл бұрын

No. Sorry.

@ForceOnTwoWheels

4 жыл бұрын

Craftman Blower 25cc Carburator www.searspartsdirect.com/product/431tc01p4b-0071-358/id-530071775 How to replace carburator www.searspartsdirect.com/diy/repair-guide/how-to-replace-a-leaf-blower-carburetor How to rebuild carburator www.searspartsdirect.com/diy/repair-guide/how-to-rebuild-a-leaf-blower-carburetor

I work on blowers for my boss for his business I have a couple that will only run it half choked too I'm almost 100% sure it's related to the diaphragm gasket

@Paisteboy

2 жыл бұрын

That sounds like a possibility. I'm not a mechanic so I can't say with confidence what the true cause is. I usually start with a cleaning and go from there.

Where buy this little hose

@Paisteboy

3 жыл бұрын

Lawn mower dealer will have it.

Great video! You can use a small electrical connector on the end of a screwdriver to adjust the carb!

@Paisteboy

9 жыл бұрын

HarryCo4 How do you mean?

@FlyByTire

9 жыл бұрын

paisteboy Here is a photo: drive.google.com/file/d/0B2QfCEBctnYpQU1tdjFXbHlwSW8/edit?usp=sharing

@Paisteboy

9 жыл бұрын

Ok. Thanks.

@FlyByTire

9 жыл бұрын

paisteboy Just turn the low screw out a bit when its on full throttle and it should run good!

@Paisteboy

9 жыл бұрын

Ok. Cool, thanks. I'll do that.

Pastieboy; Like the lady said , '' I've cleaned carburetors with junk in them. They seldom ran. Your carburetor has nothing on the screen , as mine did. Yours look like new. I would like to see you clean one that didn't start, before you, took it apart and cleaned it. I think nothing was wrong with it from the start. Sorry for the skepticism!

@Paisteboy

7 жыл бұрын

I hear what you are saying and I don't have all of the answers. I'm not even a small engine mechanic. I do know that some of these machines have a carburetor problem right from the factory and cleaning and rebuilding only help temporarily. I have a weed eater that my brother just gave me and it's having problems that a shop said wasn't worth fixing and the machine is only a couple of years old.

You're using carburetor spray and it's not good on rubber gloves. It starts dissolving him as soon as it hits them so how dangerous is the carburetors very it says not good for rubber or foam the foam will swell up like a balloon

@Paisteboy

6 жыл бұрын

Parts of your sentence do not make sense. What does this even have to do with foam? There is no foam in a carburetor.

You can order a whole pack of those special tools Amazon for 10 or $11

@Paisteboy

3 жыл бұрын

Thanks for the tip

I also ride a Harley and have a similar looking shop !! LOL...

@Paisteboy

9 жыл бұрын

Vdubin64 Nice.

By the looks of everything it almost looks like a Craftsman

@Paisteboy

3 жыл бұрын

I think it is a craftsman.

Bad gas from a good run like that old gas you stabilizer in your gas

@Paisteboy

Жыл бұрын

I do.

Look away from the camera 😂😂

@Paisteboy

4 ай бұрын

😂

The check valve in the idle circuit of the carb is bad.

@Paisteboy

7 жыл бұрын

Thanks. I'll look into that.

For what it's worth , That blower looks exactly like a Poulan BVM200LE only with black plastic housing instead of yellow. And since Craftsman is notorious for slapping their name on other manufactures stuff , you might want to check to see if the bolts holding the cylinder to the crank housing are loose. It's a very common problem with the BVM220LE's . You can see it on this video : kzread.info/dash/bejne/pm2VwbZxg9K2Z7w.html

This guy cleans his house with carburetor cleaner.

@Paisteboy

4 жыл бұрын

Only on Sunday!

where's the coil

@franklivingston9372

3 жыл бұрын

at the end of spark plug wire

WHEN YOU SAY PUT THE BIGGER LINE ON THE TOP /SMALLER LINE ON THE BOTTOM , WHAT IF YOU SAY PUT THE LINE WITH THE FILTER ON TOP / LINE WITH THE RETAINER AT THE BOTTOM . IF THAT IS RITE HIT ME BACK PLEASE. OR DO I HAVE THAT WRONG .

@dennisvoelker664

4 жыл бұрын

From the experience with mine the filter line goes on lower line on carburetor.

@Paisteboy

Жыл бұрын

See below. Can't remember. it was too long ago. Sorry.

At time mark 12.55 of the video u missed a leaf. Lol

@Paisteboy

2 жыл бұрын

Lol. Thanks for watching.

@HuckBuddies

2 жыл бұрын

Absolutely wish more content creators would reply to comments. U now habe a new subscriber. Thanks

@Paisteboy

2 жыл бұрын

@@HuckBuddies Thank you. I really try my best to reply to all comments.

you didnt show how to remove it . that should be the first part

@Paisteboy

3 жыл бұрын

Check out my other bower carb rebuild video. It might help. we remover the carburetor from the blower on that video. kzread.info/dash/bejne/l6ObuJl9p7O6ntY.html

& there could still be trash in the needle seat, lmao, good job there buddy

@Paisteboy

3 жыл бұрын

Thanks!

never never spray carb cleaner on the rubber parts of a carb ... just like your gloves they're all out of shape now and won't work you'll need a carb rebuild kit

@Paisteboy

6 жыл бұрын

Thanks for the comment.

My name is Plaisted. What is yours?

@Paisteboy

2 жыл бұрын

That's close to Paisteboy.

@thomasplaisted3579

2 жыл бұрын

@@Paisteboy my name is Plaisted. Where are you from? I am in Ohio.

I hope your wearing a mask😮😷

@Paisteboy

7 сағат бұрын

👍

Carb cleaner on rubber parts destroy them

@dustyrhoads5016

5 жыл бұрын

seadooman o do you think maybe that’s why his gloves got all blown out of shape😂😂😂😂

@Paisteboy

Жыл бұрын

I now known that.

wouldn't u know it, there isssss, running it 1/2 choked

@Paisteboy

3 жыл бұрын

Yup.

Hi by the time you took car of to reb you can by new car for 12.00 ear of eBay thank you