How did you guys like the video? If you guys want to see more about the warrior I will be posting updates to my Instagram throughout the day: 2_vintage_ instagram.com/2_vintage_/

@lauritssrensen4970

4 жыл бұрын

2vintage Ilm form Denmark

@josephornelas8494

4 жыл бұрын

What’s up with the ratchet??

@Greywolfwarrior

4 жыл бұрын

Love the video 👍 great machine glad you picked this one up 🤟🤙

@estrinavic5048

4 жыл бұрын

Love the videos 2vintage keep them coming ive actually learned a few things after watching them thank you guys from down under

@zackcalfee4844

4 жыл бұрын

Hey joe I've had a few of those quads back when I was a kid, yamaha failed on something when it comes to start em, you can pull the side cover off and heat the magnotta and it will start very easy, but 1st you need a starter it's really not turning the engine over hard enough, and those older warriors like that 1 have to play with the choke and barely give it throttle

Warriors are outstanding machines. We had one that we bought new in 1989 and it ran flawless until it was hit by a sandrail in 1997. We JB welded the case replaced the swingarm and off it went again for another 4years until we sold it. Great find Joe I love these bikes.

Step one pressure wash step two drain all gas out of the machine step three try for spark step four clean carb step five try to get it to run the rest is water under the bridge

The one way starter clutch bearing is shot...

@mxbeanz1206

4 жыл бұрын

I hope he reads this. It's so obvious theres a starter issue.. it sounds horrible cranking

@cimotorsports-atv

4 жыл бұрын

@@mxbeanz1206 ive been working on atvs for 20yrs. I can tell just by how its cranking that the starter clutch bearing is slipping. Why it doesnt fully crank over fast enough

@jacknelson9440

4 жыл бұрын

@@cimotorsports-atv mine was wayyyyy worse it would slip for like 4 seconds then grab once then slip again then she gave out eventually it would just slip

I'm 10 mins in no wd-40 in sight

@shadowdancer2131

4 жыл бұрын

Yaeh!😂

Cleaning the carb would always be the first thing i would do

@evatheboxer7417

4 жыл бұрын

johnsn10 should always

@killaz123456789100

4 жыл бұрын

Yup always first

@unussgamersszz9644

3 жыл бұрын

Carb cleaning can wait until bike or quad is clean cuz if any of that dirt gets in the carb you scrood

@MDHenry4

3 жыл бұрын

He bypassed the carb by going directly to the spark plug opening. I have never done this nor seen anyone else do this. I always pour fuel through the intake valves to bypass the carb. These days with ethanol the carbs and gas tank are always a mess plus when you add time and years of neglect. Battery connection also always come loose so that is always high on the list.

Just broke a ramp that’s worth more than the quad... i was sooo waiting for a f..................k😂

@hairymcsnatch1340

4 жыл бұрын

This is the comment I was looking for 😂 he didn't even say anything not even a reaction 😂

You didn’t check for fuel and didn’t clean carb

Def the most reliable engine ever assembled.

uh didn’t he say there was no gas in it and then tries to fire it 5 minutes later?

He likes his worriers lol

@purplehayze420

3 жыл бұрын

Warriors

@temporalnacho2606

3 жыл бұрын

@@purplehayze420 Not only was your grammar correction unrequested annoying, it's also about a year late.

@purplehayze420

3 жыл бұрын

@@temporalnacho2606 and did I ask for your feedback see every these days get Nothing but butt hurt over little stuff pathetic

@temporalnacho2606

3 жыл бұрын

@@purplehayze420 that made no sense. Lmao

Wow I'm excited for this project 1996 warrior 350 that's one of my favorite color plastics for that machine 👍 nice tires on this one too 🤟🤙

I have a 2001 Yamaha warrior and they are a beast ‼️‼️‼️

@Greywolfwarrior

4 жыл бұрын

Yes they are 🤙

@aidentrussell7016

4 жыл бұрын

Same

Loved the videos don’t let people tell you otherwise! Great job always want to be like you!!! 👍🏻

I ♥️ the measuring cup and straw used for adding half a drop of gas into the cylinder!!👍😂😂 spray wd40 everywhere it should start after that!!🤕

You actually think grease fixes loose bushings on your a arms? Wrong

Power wash in the side yard would save you a lot of time. The Velcro was probably from 1 piece, over the tank, saddle bag. Velcro would keep bags from flopping around and still allow you to remove bags easily if needed. Your next project should be a small work bench 3'x2' and waist height. Possibly even on wheels to move it around. This way you aren't working on the ground. You'll really appreciate it when you are working on carbs and small items. Hope you get it running.

Good luck, hopefully it something simple or soon enough you’ll be adjusting valves, doing dumb things like oil pump, stator, intake boot, had a mint 99 that ran amazing but had some weird quirks that 3 experienced owners could never seem to be figured out even after rebuilds. Wiring is funky on them sometimes too check your neutral and parking brake wiring. If you have any questions on where to start if it’s just giving you weird results I may be able to shed some input!

@danniellebrightbill9951

4 жыл бұрын

Ps that’s my favorite warrior color scheme ever, my 99 was all red with gold rims, decent.

I've owned 2 warriors an 89 and 95 loved them,had them for a couple years but sold them(kind of wish I kept one)and upgraded to a 2019 Raptor 700r

You are a very optimistic person lol. $400 a great deal but all I see is trash. Cant wait to see the transformation though honestly. I bought a perfect running 07 KX250F for $629 lol. Such a odd price I know but my haggle game is insane. I plan to do future rebuilds as long as this one goes as planned

I love warriors. And i WATCH ALL YOUR VIDEOS. I just rebuilt my 35o warrior all thanks to you. So thankyouuuuuuu

Here's a tip for the cleaning up oxidized plastic wash them down and let dry spray them with nonstick cooking spray let it sit for about 20 min and then wet sand wipe them down done i came up with the trick and it looks factory and cleaning up after a ride is easy and the finish last for years

Love your videos! Have you thought of doing a honda atc 185s-200s-200x- or 200es build? I would love to see you build one! They're super easy, to work on and dead reliable. Plus they're really cheap

But you didn't let it warm up...Bro!

I put a cone filter on ours Joe, made a huge difference. Kept original airbox but leaving the cone on. Easy yo clean.

that ramp has been bent up since the quadzilla. heat gun will fix it, and the carb failing that get the wd40 on it

Love the videos bro

Well I like it better than the last one. Good luck

Great work keep up the good vids

Swapped out gold wheels for a set of douglas low pro's. Put some hole shot racer tires on all 4 looks pretty sick, just rides a bit low, warrior thing. Great vid@

Yea I like that one old school nice vid bro

stabbing that thumb throttle while you were trying to start it was really triggering my OCD. All I could think was "please please stop doing that for the love of god." I never had to touch the throttle on my warrior, pull the choke, hit the button, let her rip.

I’m just here for the comments 🍿

to bump start a high compressed bike you put it in 4th and push it will turn over

@2vintage

4 жыл бұрын

I did, still hard to push

@bendube9322

4 жыл бұрын

2vintage I have a Honda 300ex the starter was gone and didn’t have the money to buy a starter so I had to bump it for 1 yr and my bike never started in first it would never turn over it had to be 3rd or above that’s all I know about bump starting

@whatintownation6347

4 жыл бұрын

You need a good hill to go down

I will get mine on friday and im so hyped up from your Videos. I will drive 7h (one way) to get it 😂

I love watching your channel and how conservative you and explain as you go thru each project but on this one first step directly to the car wash would have saved hours . love your channel .

By the way, messing with the throttle sometimes makes it not start because when i had my four wheeler when i applied throttle it wouldn't start

Looking like it should clean up well!

Why does it sound like the battery wants to die every time when you start it..?? It happened on your other warrior too mine doesn’t do that???

Spray some carb cleaner or easy start down the air boot if it goes to start you know the jets in the carb are probably blocked. And fuel isnt reaching the combustion chamber. If it dont, do a compression test. Hope ya get it working!

It would save you a lot of time if you cleaned the carb first. Then you know it’s getting fuel. Or see if it hits off starting fluid or carb cleaner. Function is more important than looks. Still in a lot better of shape than the first warrior project

Honest. It ran perfectly when I parked it

@2vintage

4 жыл бұрын

@@fdrc8099 oh yeah I've had people use the selling for a friend before

Starter is not turning motor over fast enough it’s to weak.

My moto 4 would crank forever, just make sure the jets are clear

FYI instead of the shaft shifter you can use a yz250 2 stroke direct shifter

You did put gas in it right?

I like the spidertracs on the tears cool tires you don’t see them much anymore

I love 350 worriers there cool quads good video

Here's a tip to find the year. I'm not 100% sure but if quad VINs are like car VINs the 10th digit will indicate the year.

Yes another one as soon as i buy one

Banshee running on one cylinder "OH BABYYYYYYYY THIS IS FAST" wont touch the cr lmfao. Little nicky you are a funky dude. That tri zinger is more your style.

Do a 400ex I got one for 690 06 runs drives road it all day you can find some good deals

U otta pressure wash the whole thing and try to get all of the gunk off... I think it would turn out pretty nice

Did he clean the carb? This dude really cleaned it the exterior before the interior first thing to do check spark,gas and clean the carb it cant run if the jets are clogged

The decompression valve is only on 87

Normally u have to have the clutch pulled in on worries to even get them to turn over that's kinda wired??

Disconnect carb, squirt a bit of gas directly into the spark plug hole and get it to burp off. This will give you a lot of information.

Did you fix all those vehicles your self if u did then dang I'm your biggest fan

The one way bearing on the starter clutch is going Joe you definitely need a new one but reading the comments you obviously know that now... and if you get another machine dude check out a Honda 300EX they are probably the ultimate Trail machine or an lt230

I have a complete seat for th hat as well, n eeds a new cover but complete.

Oh yeah the battery pack works amazing 😅😅😅

I had same exact color one mine was an 02

Can anyone tell me what the green and white wire hook up to on a warrior by the reverse lever

Hey you forgot the nice rims it's sypposed to come with like you said in the begining

Reverse lever always get stuck on those and th3 crankcase is usually Beat!

You'll get er running again.

U need a battery jumper u need a lot of power to get it to crank over fast enough for it to start it up

You could roll it off thats what I do with my four wheeler when I don't have a battery

Already knew it was ganna another Yamaha Warrior 350

Sounds like the Woodruff Keys broken the one way bearing/ flywheel is spinning on the crank

I got one do 400 in way better condition it just smokes a lot what can I do?

The reverse lever wasn’t fully engaged in forward

You flooded the cylinder with gas then expect it to start 😂😂

Yay love warriors do a speed test.

@whatintownation6347

4 жыл бұрын

It should do close to 60

@thedevilr4420

3 жыл бұрын

@@whatintownation6347 they do a little over 60 like 63

Where should I go to buy randown and non running bikes and quads for projects

What’s the glossy stuff u put in the plastic?

joe I hope you have to use to drill to start it like the last one that was funny as crap when it started keep the videos coming

@2vintage

4 жыл бұрын

Lol.never again

Awesome vid love watching u on here first comment on your vid I'm 18 years old and i have a KZread channel #notificationsquad

I new it was a 96 but the looks I had the same machine there not bad quads

Im just going to buy a rm 80 1983 for 400€. 40h piston and crankshaft (They have been used for that time)

Good job

No dought a bad starter clutch. Y olly could try once removed to clean it and hope its "build up" causing fault. Ive seen it broke a couple ways

you should do an old beat-up ltr-250 resto

Lol on the way home he said lights worked got home let’s see if the lights work yeah lights work that’s good lol

The last time I met someone from Craigslist at night I bought a "blue" Stratocaster that turned to a purple in the daylight.

Before I watch this yes ,it will.

It has no compression for whatever reason Valve timing or whatever it does not turn over properly

I'm interested in lt500r quadracer had on your video

@pinkdoor6788

4 жыл бұрын

Not to be a little bitch but quadzilla is the name homie. The quadracer is the 250 2 stroke and the quad runner is the 4 stroke.

No petrol in the tank you said so is that why it ain’t starting ?

Why would you use a flat head screwdriver to clean off all the oil on your frame

Just asking what do you guys & girls think about a Honda 2000 XR 80 R 4 Stroke Just would like to know your opinion? Thanks

Sounds like the engine isnt turning over fast enough for compression to get high

Still double check the starter/ starter clutch

I miss my warrior. I've been looking for another one

Hey bro i love the videos would u sell me the outer black peices on the front fenders

It’s nice quad

Air compressor for loose dirt?

Did u get this bad boy running? I am about to buy one for the same price.

I like your videos, my uncle does the same stuff you do, we have the same warrior that was in a shed for like 12 years and we polled it out and got her going, I’m going to send you a pic on Instagram,we have some extra parts to. Keep up the good work

Uhh starter fluid?

@ronrichards2691

4 жыл бұрын

Starring fluid sucks if any thing a lil. Skwert of gas