Appreciate the safety reminder. So many channels don’t show that they wear PPE while they work, making it easy for newbies to omit.

@gz625

8 ай бұрын

I would say that it's a natural selection - but things are MUCH worse. Those dummies who are not smart enough to read manuals and use safety gear making higher pressure on economy. They are sick more often and require expensive treatment. So they hey not only dumb and harmful for themselves but the whole society.

@dfloyd888

8 ай бұрын

I think I may stick with FDM prints which have far less toxins, and are a lot more idiot resistant than resin.

@TM-ro7lh

7 ай бұрын

Neeeeeeeeeeerds 🤣

@JustErix

7 ай бұрын

​@@TM-ro7lhshut up

@Bl0ckfett

7 ай бұрын

Yes, and the best part is that you don't have to wear a gas mask at all with a 3 day beard. Because the sealing line is completely useless. Eve full beard is a bit better.... it's btw... no bashing or so.

The second method using the Alclad metal lacquer paints can be improved by using the chrome paint again instead of the gold, you add a little yellow and a small amount of red food colouring gel to it, it produces a highly reflective gold paint. A prop maker on YT documented this method when he was painting medals and showed how it holds up on his wearable C3PO costume. His name is Gordon Tarpley, he has useful tips on technique too.

@bluelotuslandscapes

8 ай бұрын

Don't even need to mix the colour into the Alclad. Just use Alclad Chrome as normal, and then spray with clear Acrylic yellow or orange paint over the top to get a shiny gold. Use a range of different clear colours to get a whole host of metallic and candy finishes. Yellow or orange on their own aren't quite right for a true gold, but Tamiya Clear Yellow mixed with just one or two drops of Tamiya Clear Orange can be spot on.

@hen3drik

8 ай бұрын

Tamiya clears are so nice. I actually spray them as candy on my nickeled parts.

@MaximilianonMars

7 ай бұрын

🤔 good tips! Thank you

@andreacook7431

2 ай бұрын

You could always mix a little bit of Alcad copper with the gold. I've had good luck mixing silver and chrome to make a good "base" for space kits. (It's also great to use gunmetal and white aluminum to do a zenithal for Cybermen)

7:11 electro polishing Electropolishing is an electrochemical process used to polish, passivate, and deburr metal parts. During this process, the metal part is submerged in an electrolyte solution and connected as the anode (positive electrode), while a cathode (negative electrode) is also submerged in the same solution. When an electric current is applied, metal ions are removed from the surface of the part, smoothing and polishing it. The process can refine surfaces at the microscopic level, remove burrs, and improve the corrosion resistance of the metal. Commonly electropolished metals include stainless steel, aluminum, and nickel alloys.

@stevendorries

8 ай бұрын

So you put electroplating in reverse?

This is pretty incredible for RF filters/antennas! In radio frequency design the full conductor can be replaced by a thin copper sufrace due to the skin effect. This means you can 3D print most (very expensive and often custom) RF components now!

wow, the sound after electroplating was so surprising!

Thank you for leaving the outtakes in when talking about the chrome paint, as a fellow german I can relate "boah"

@hen3drik

8 ай бұрын

You‘re welcome 😅

@1337fraggzb00N

Ай бұрын

Rein in die Futterluke!

Honestly,. the minimal effort resin one is the most screen-accurate, as the commbadges have a more satin finish than plated. Not to mention, that's pretty much exactly how they were done for the show, too.

@hen3drik

5 ай бұрын

You‘re are absolutely right. I think I made more of a „dream-what-if-prop“. 😅

Another important reminder for working with resin prints, the actual resin dust is pretty horrifically bad for you too. I suggest a mask and ideally a vacuum cleaner turned on with the nozzle near to the print to just suck up the dust as it's made. (Ideally it'd have a hepa filter too)

@hen3drik

8 ай бұрын

Good point. Wearing a mask with particles + dust + A2 protection does the job for me.

@pistachoo.

5 ай бұрын

Do you mean the dust from sanding? Good to know!

Thank you so much for showing us you using gloves, and respirators. The amount of channels that either don't or don't themselves take safety measures is WAY to high.

There are many layers to the techniques in your second method for getting a mirror finish. When done right it'll reflect like a mirror. A big contributor is the black paint that's used. It has to be very thin otherwise you'll end up with a bumpy surface. Proper sanding and polishing before is also important, and you can use automotive polishing compound to get that mirror finish after sanding. It's not that important if you're electroplating, but for many of us being able to have metal like finishes with paint alone is definitely achievable through paint with some practice.

@michaelmichalski4588

5 ай бұрын

Toothpaste

Great video! While you used a black base- layer for both colors in the medium phase, If you used a red base-coat for the gold one, it would read as much more "golden"

@hen3drik

7 ай бұрын

Thanks for the hint. I read this at least twice now. A lot of pros out there (I’m a paint noob) 😅

Kudos for highlighting the use of PPE 👍 So many makers set bad examples.

@hen3drik

5 ай бұрын

I do, every single time. It’s so important. And you can make it quite amusing. 😃

Try metallic lacquer some time! You spray a coat of gloss black and a coat of silver/gold, buff it with cotton, and finish it with a layer of clear. It takes a couple hours from start to finish and you can buy it in rattle cans or airbrush-ready.

You’re a life saver when it comes to tutorials, from helmets to weapons, to small props. I’m currently making a Batman costume for Halloween and electroplating, couldn’t have done it without you!

Thank you for all you do for hobbyists. I’m building a garage studio and you are the most informative source I’ve found!

Final electroplate result looks absolutely amazing. Even the airbrush resin one looks great. Can't wait to start soon, perhaps I'll get myself an electroplating kit for Christmas!

@hen3drik

8 ай бұрын

I got my first for Xmas, too 😅

@jothain

8 ай бұрын

I didn't know there are ready kits. Are there many suppliers in Europe?

@zakr1187

8 ай бұрын

Kit from where?

@bluelotuslandscapes

8 ай бұрын

@@jothain Europe is actually really good for electroplating. Look for the Tifoo brand. They seem to be a LOT cheaper than in the US or Australia and they work well. I think @hen3drick uses a lot of Tifoo stuff. In Aus we basically have Caswell which is STUPIDLY expensive, or a bunch of cheap no-name knock-offs which may or may not be any good.

Have you considered trying Electroforming? Basically the same as Electroplating except you plate onto a silicone mold that has conductive paint applied and are left with a copper shell that you can electroplate onto. It's yet another step and requires a bit more copper but I think its kind of neat to be left with an entirely metal part in the end.

Looks great. You should try high gloss spray paint then graphite powder and the finish with clear yellow paint. That's what I used for my Mandalorian. Super mirror reflective without the electroplating.

Such an impressive process. I love the look and the sound of electroplating!

For the low effort method, you could add a step of using self-leveling primer. Not sure it will be enough to fill very rough layer-lines, but it should give a better result with not much more effort.

One of the best finishing videos out there thanks!

Awesome video. As always. If I ever get out of apartment living I will try this method out. For now. I can just enjoy this these master classes. Thank you!

Ironically, the first resin print was probably the most accurate as the screen used badges were dull to avoid reflections.

@hen3drik

8 ай бұрын

so true. also the colors were quite matching the original prop. The electroplated is more of a "hero prop" as it's what I personally had crafted for the show.

You can make an magnetron sputterer from a jar and a vacum pump. You can plate almost everything with that

For painting with either aerosol or airbrush, your base coat matters a lot. Rather than black, a brown or dark red may help (I've even seen some that use a pink basecoat). Alternately, try a test piece, and add brown or a dark red to darken the colour a bit and make it warmer.

they even sound metalic!!!!

These videos are great. Thank you for the great content you're providing!

very impressed with how good these came out, especially the fdm ones! I've seen one or two people use a similar process to intentionally rust parts to give them a weathered metal look but there seems to be very little info on it out there. I'd love a demo showing the best ways of doing this!

It's fun to think that those badges are small enough to fit the entire pcb of an earpod clone including the tiny microphone chip. So all that would have to be done would be linking touching the badge with the pcb's touch component to trigger a voice assistant.

The airbrush ones looked really good

That electroplating is verry cool! :D

ELECTRO POLISHING - and one thing, though. Resin prints can be polished to a mirror finish as-is. They'll look like a piece of acrylic then. Would be interesting to see the second method on such parts.

wow, the last one looks amazing

8:20 the electroplated looks so good I feel like I just learned a secret hack to make anything look perfectly chrome or gold

@hen3drik

5 ай бұрын

You actually did 😅

Those are impressive results!

Your com badges are beautiful . Two lesser known things about them: on the show, they're painted with a rattle an and they're not gold, they're painted brass Nevertheless, excellent work!

@PendragonDaGreat

5 ай бұрын

I was thinking that the result was too "bright" and that the originals were slightly more brassy.

This is simply amazing!

Another great video! I look forward to every one!

This is a good candidate for solvent smoothing.

gold plated PLA, my mind is blown :: thanks for this awesome video!

Fantastic results. I've had some fun experimenting with copper sulphate but no serious project yet. I have discovered that dropping rusty nuts and bolts in solution and leaving for a few hour gets underneath the corrosion and basically removes if. The very slight copper layer is then easily removed using a wire brush. A little of topic I know. Thanks for the great video.

My jaw is on the floor dude. 😲 Very nice

Your face and body protection is better than 99% of KZreadrs!

This is purely amazing 😍

That was just cool. I've never gotten into electroplating for stuff like this. Only with nickle for electronic stuff. This is so amazing!

@hen3drik

8 ай бұрын

It opens up possibilities 😅

when painting with metalic paints both spray and air brushing, put a black gloss base layer, let it dry for at least 24h and than the metalic paints, youll get amazing results.

Das ist so cool!! 😮😮😮 Sehr beeindruckend!!

_bites into it._ Gold!

Beautiful print and plate

That's amazing!

Endlich jemand der weiß das Resin Krebserregend ist und deswegen Maske/Handschuhe nutzt 🎉

The middle and best are amazing, for cosplay the middle one is very acceptable. Thank you for a very interesting video

Very cool!

I love your the electroplating process, especially as former jeweler who learned to do this in school for plating metals and did it a lot on the market. After seing your result with 3D printed props, I am now scared of scammers comming in with a new twist on the fake gold jewelry trick.

Super Überblick zu den Methoden. Echt tolle Ergebnisse!! Danke für die Sicherheitshinweise.

@hen3drik

4 ай бұрын

Sehr gerne!

I just found your channel, it's WONDERFUL stuff!! and nice subliminal text on electropolishing! 🙂

Amazing!

Great video. While I love the electroplated result, the airbrush seems to work really well too.

Vielen Dank für Ihre Video! Sie haben den besten Inhalt.

Hi, thanks for the new e-plating video. With what did you have the better experience on e-plating 3D prints? Copper or grafite base and why? I think about to base coating my 3D-prints via airbrush and wanna buy something quite soon :) Hallo und danke für das neue E-Beschichtungs-Video. Mit was hattest du bisher die besten Erfahrungen beim Beschichten von 3D-Drucken? Kupfer oder Grafit-Grundierung und warum? Ich denke über die Grundierung meiner 3D-Drucke per Airbrush nach und möchte zeitnah etwas anschaffen :)

Haha dein Versprecher sehr sympathisch ich kann nicht einmal 2 Prozent so cool Englisch sprechen aber verstehen klappt super bei dir sehr klare Aussprache 👍👌danke dafür und für die guten Infos

I love this channel

c'est trés jolie j"aime beaucoup! Viva Star Trek

and then someone comes along and produces awesome results using nail polish^^

Super video👍

Awesome video

I use method 2 with a Red or ocre base to get a richer gold color

yeah allclad paints! My father and I use them in our model paint jobs.

Absolutely amazing results with the electroplating, your videos have inspired me to try electroplating my resin prints, Ive started the pokeball😊 would be brilliant if you could do a more in depth tutorial on the electroplating itself, there seems to be loads of contrary advice on the interweb😮

Super geworden!

My go-to gold paints are gaiacolor 132 pearl gold, and 122 Starbright gold

Awesome video! You are the master of electrating 3d printed parts. ;-) BTW ... usually best smooth results should be achieved using wet sand paper (ger: Nass-Schleifpapier). Wet sand paper is used before car is getting painted. You should change from dry to wet sand paper. The result will be so much better.

@PeteCorp

8 ай бұрын

Use self leveling high gloss paint

Wow!

Thanks for explaining the grits that you use when sanding each layer of filler, primer, etc. I had to find out a method that worked for me through lots of trial and error, but it would be nice to get a more in-depth video explaining your process to get glass-smooth prints (including names of each product used at each stage, grits used at each stage, buffing compounds & their grits, etc... whether you sand with 1000+ grit between paint layers, etc, etc). For example, this is my process (which may be overkill... or their may be better ways to do it... which is why I think sharing your way could be helpful too): _My process (quite light sanding pressure, so you dont scratch things too much):_ 1) 220 grit sanding to take off any zits / sharp edges and knock layer lines down a tiny bit 2) Single coat of Primer spray paint 3) A couple coats of Motip Spray Putty to fill the layer lines. 4) 400 grit sandpaper to smooth it out. If you can still see / feel layer lines with your nail, then go back to step 3. 5) Spray with Filler Primer, then sand smoother with 600 grit 6) Spray with Primer, then sand with 800 grit 7) Spray base color coat, sand with 1000-1500 grit between coats (dont sand last color coat) 8) Spray a few coats of clearcoat 9) Switch to buffing/polishing wheel (sponge pads on my drill)... using buffing compounds 1000, then 2500, then 3800 This will get you a smooth mirror-like surface... like the surface of a show sports car... but you can stop at lower grits of sanding and ignore the buffing compound with buffing wheels/pads if you dont want that level of insane smoothness / shine. Most times, you can stop at 400 grit and not need to go higher because you wont need that smooth a surface.... but any higher grits than 400 will generally need to be wet-sanded to avoid clogging of sandpaper.

On fdm, I would print the center peace as a flat part on a smooth glass bed and bent it with the help of some heat to the main peace.

8:06 i wasn't aware, thank you

Top ! Danke

@hen3drik

8 ай бұрын

Gerne 😊

With airbrushing, I would try different basecoats to get more of a silver/gold color - use white/yellow underneath instead of black, or spray everything silver and put gold on top of the silver

The electroplated materials look fantastic. How difficult is it to avoid and/or remove the fine surface scratches on those samples?

3:22 for gold metallic paint it tends to look better over a red base coat instead of black. Although my experience and where I lernean it from is for miniature painting so might not apply the same to large models

Respekt! Das sieht Mega aus, mir wär's aber zu heikel. Außerdem, mein Dorf Wertstoffhof würde mich hassen wenn ich mit sowas daherkommen würde. 😂 Danke für die super Videos!

@hen3drik

7 ай бұрын

Gerne! 😃

That's beautiful. Now how do you fit the communications electronics inside?

Boah, great video!

If you print something with a flat top (like this) and you enable ironing. You can get near-mirror results from metallic spray cans.

@hen3drik

4 ай бұрын

Unfortunately this doesn’t have a flat top.

That's great and all....but what machine and setup do you have? Thanks

Logical.

Cooler Kanal👍

FDM + Acetone fumes seems like it could fit between low and medium effort

Tolles Video! Des Endergebnis sieht echt spitze aus! 😁👍👏👏👏 Hätte es toll gefunden wenn du noch ein paar links zu den verwendeten Chemikalien in der Beschreibung gehabt hättest. Will mich auch mal am galvanisieren versuchen.

wunderbar

OMG VOYAGER FAN!!!!!!!!

Airbrush seems good enough for a prop. Electroplating seems a bit of an overkill

I think the phrasing you're looking for is " I'm not that experienced, so someone with more experience could achieve a better finish"

Good Video, thank u!👌 Why don't you use wet sandpaper? The surfaces become much smoother Have you ever tried Molotow's Liquid Chrome? In my opinion, the best "chrome paint", but requires a lot of prework.

Badgey!

I get why people think the electroplated one looks best, but the airbrushed one looks a lot more screen accurate. Even in close-up shots of the combadge, you don't see reflections, they are all matte anyway. Yes, I understand this is a video on finishing 3D prints... but come on! Star Trek!

I accidentally shorted two copper wires next to a plastic bit of plumbing and to my surprise it became nicely copper coated on the exposed side of the plastic, is there a more refined way of doing this plasma coating on plastic?

There was an old trick on KZread where you would zinc plate then copper plate a quarter and use a torch to melt the metals to form brass. It looked awesome and will be basically corrosion resistant without being expensive like gold. But since idk if that would be too much heat for 3d printed parts, I would love to see it tested!!

@hen3drik

7 ай бұрын

Oh, it’s working like a charm. Will show some time. 😊

@kenshiromilesvt.7037

7 ай бұрын

@@hen3drik awesome!!!!!!

it depends what part of the costume I would like to make the armor and premeditatedly allocate the main salaries from fdm waste

mega gute videos. hat duschonmal darüber nachgedacht die videos auf deutsch zu machen

@hen3drik

2 ай бұрын

Danke