Thanks for the video! Im doing one now! The starter is grinding. So im going to replace the starter but i think something else up inside there is bad!
@georgedunham85152 жыл бұрын
Thank you, I to have the same problem, do you know what the torx is to put it back together?
@eqd053PB2 жыл бұрын
How did you get the bearing back onto the flywheel when reassembling?
@heatherhobbs5693 жыл бұрын
So when you put the fly wheel back on do you need a tool to press it? Or how did you get fly wheel back on?
@eddiegossett8218 Жыл бұрын
great video not a hard job 👍 👏
@loranstaley11193 ай бұрын
Before the cover comes off there’s a bolt that goes into the shaft, how did that come off since it spins with the crank shaft when you turn it. And is it reverse thread since on a shaft? Tearing into mine now
@clydeshelton65332 жыл бұрын
My starter dropped a magnet and locked it up. Now it free spins. Idk what the damage is. But breaking into it now. 06 prairie 360 4x4.
@circleo59243 жыл бұрын
So are all the broken teeth just scattered out In the engine?
@darrelladen17793 жыл бұрын
Your video was so helpful. Thank you. Where did you get the part from and do you have a part number? I have a 2005 Kawasaki 700. Same problem as you
@paoff-road7849
3 жыл бұрын
Part - lj2368sc120bh starter gear , clutch and gasket from caltric on eBay the flywheel puller was also from eBay seller was dt918 - $52 bucks for that just be careful when installing the stator wire grommets if you get them wrong it will leak I also used black silicone for that
@darrelladen1779
3 жыл бұрын
PA Off-road Thank you!!
@darrelladen1779
3 жыл бұрын
Did you get the torque specs? I’m putting mine back together tomorrow
@alexgervais31883 жыл бұрын
Do you have a rebilt video
@nathancd3 жыл бұрын
Curious as well if you were successful.
@mjl70233 жыл бұрын
What did you do to press the magneto back onto the crankshaft?
@paoff-road7849
3 жыл бұрын
It slides back on pretty easy no need to press fit
@dazbill99053 жыл бұрын
I am having troubles removing the cover. I removed the 12 bolts and water pump what am I missing?
@paoff-road7849
3 жыл бұрын
Shouldn’t be that hard to remove did you remove the impeller ?
@jrhodes64903 жыл бұрын
Do you need to worry we’re the top dead center tab is at, and also if you could post the torque that be awesome
@paoff-road7849
3 жыл бұрын
No since you’re not removing the timing chain - I’ll get back with the torque specs I can’t recall and don’t have them with me
@heatherhobbs569
3 жыл бұрын
94 ft.lb is specs
@wolfmanchilds4202 ай бұрын
lol I’m down the street from them guys lol
@JerseyFrank0073 жыл бұрын
Did you find all the broken teeth?
@paoff-road7849
3 жыл бұрын
Yes got them all out with a magnet
@josephedwards71802 жыл бұрын
Brute force hot light stays on
@michaelblinco67043 жыл бұрын
Would you happen to have the Phone number for turtle fountain where you got the Puller from
@paoff-road7849
3 жыл бұрын
Purchased on eBay I’ll check and see if the phone number is still there
Пікірлер: 32
Thank you , just had the same problem. Your video saved me a lot of grief !
@kidzkiddo4962
2 жыл бұрын
12jjnmy212 2jkmmjytrttmmm233emmmrr Mqwnhhhh=#e÷eeedfnnnvbbbfdrrrrrrre ebb ere2e2t33rggg. ....mm M.mggggtt%38
@kidzkiddo4962
2 жыл бұрын
P90pp[ 6th pp999
Thank u. Great video. Doing the same job.
Thanks for the video! Im doing one now! The starter is grinding. So im going to replace the starter but i think something else up inside there is bad!
Thank you, I to have the same problem, do you know what the torx is to put it back together?
How did you get the bearing back onto the flywheel when reassembling?
So when you put the fly wheel back on do you need a tool to press it? Or how did you get fly wheel back on?
great video not a hard job 👍 👏
Before the cover comes off there’s a bolt that goes into the shaft, how did that come off since it spins with the crank shaft when you turn it. And is it reverse thread since on a shaft? Tearing into mine now
My starter dropped a magnet and locked it up. Now it free spins. Idk what the damage is. But breaking into it now. 06 prairie 360 4x4.
So are all the broken teeth just scattered out In the engine?
Your video was so helpful. Thank you. Where did you get the part from and do you have a part number? I have a 2005 Kawasaki 700. Same problem as you
@paoff-road7849
3 жыл бұрын
Part - lj2368sc120bh starter gear , clutch and gasket from caltric on eBay the flywheel puller was also from eBay seller was dt918 - $52 bucks for that just be careful when installing the stator wire grommets if you get them wrong it will leak I also used black silicone for that
@darrelladen1779
3 жыл бұрын
PA Off-road Thank you!!
@darrelladen1779
3 жыл бұрын
Did you get the torque specs? I’m putting mine back together tomorrow
Do you have a rebilt video
Curious as well if you were successful.
What did you do to press the magneto back onto the crankshaft?
@paoff-road7849
3 жыл бұрын
It slides back on pretty easy no need to press fit
I am having troubles removing the cover. I removed the 12 bolts and water pump what am I missing?
@paoff-road7849
3 жыл бұрын
Shouldn’t be that hard to remove did you remove the impeller ?
Do you need to worry we’re the top dead center tab is at, and also if you could post the torque that be awesome
@paoff-road7849
3 жыл бұрын
No since you’re not removing the timing chain - I’ll get back with the torque specs I can’t recall and don’t have them with me
@heatherhobbs569
3 жыл бұрын
94 ft.lb is specs
lol I’m down the street from them guys lol
Did you find all the broken teeth?
@paoff-road7849
3 жыл бұрын
Yes got them all out with a magnet
Brute force hot light stays on
Would you happen to have the Phone number for turtle fountain where you got the Puller from
@paoff-road7849
3 жыл бұрын
Purchased on eBay I’ll check and see if the phone number is still there
@paoff-road7849
3 жыл бұрын
www.ebay.com/itm/180779750439