Before the cover comes off there’s a bolt that goes into the shaft, how did that come off since it spins with the crank shaft when you turn it. And is it reverse thread since on a shaft? Tearing into mine now
@kevinwalker71027 ай бұрын
Thanks for the video! Im doing one now! The starter is grinding. So im going to replace the starter but i think something else up inside there is bad!
@mechanicforlife94689 ай бұрын
Thank u. Great video. Doing the same job.
@eddiegossett8218 Жыл бұрын
great video not a hard job 👍 👏
@georgedunham85152 жыл бұрын
Thank you, I to have the same problem, do you know what the torx is to put it back together?
@clydeshelton65332 жыл бұрын
My starter dropped a magnet and locked it up. Now it free spins. Idk what the damage is. But breaking into it now. 06 prairie 360 4x4.
@josephedwards71802 жыл бұрын
Brute force hot light stays on
@eqd053PB2 жыл бұрын
How did you get the bearing back onto the flywheel when reassembling?
@nathancd3 жыл бұрын
Curious as well if you were successful.
@alexgervais31883 жыл бұрын
Do you have a rebilt video
@circleo59243 жыл бұрын
So are all the broken teeth just scattered out In the engine?
@heatherhobbs5693 жыл бұрын
So when you put the fly wheel back on do you need a tool to press it? Or how did you get fly wheel back on?
@michaelblinco67043 жыл бұрын
Would you happen to have the Phone number for turtle fountain where you got the Puller from
@paoff-road78493 жыл бұрын
Purchased on eBay I’ll check and see if the phone number is still there
@paoff-road78493 жыл бұрын
www.ebay.com/itm/180779750439
@jrhodes64903 жыл бұрын
Do you need to worry we’re the top dead center tab is at, and also if you could post the torque that be awesome
@paoff-road78493 жыл бұрын
No since you’re not removing the timing chain - I’ll get back with the torque specs I can’t recall and don’t have them with me
@heatherhobbs5693 жыл бұрын
94 ft.lb is specs
@JerseyFrank0073 жыл бұрын
Did you find all the broken teeth?
@paoff-road78493 жыл бұрын
Yes got them all out with a magnet
@dazbill99053 жыл бұрын
I am having troubles removing the cover. I removed the 12 bolts and water pump what am I missing?
@paoff-road78493 жыл бұрын
Shouldn’t be that hard to remove did you remove the impeller ?
@darrelladen17793 жыл бұрын
Your video was so helpful. Thank you. Where did you get the part from and do you have a part number? I have a 2005 Kawasaki 700. Same problem as you
@paoff-road78493 жыл бұрын
Part - lj2368sc120bh starter gear , clutch and gasket from caltric on eBay the flywheel puller was also from eBay seller was dt918 - $52 bucks for that just be careful when installing the stator wire grommets if you get them wrong it will leak I also used black silicone for that
@darrelladen17793 жыл бұрын
PA Off-road Thank you!!
@darrelladen17793 жыл бұрын
Did you get the torque specs? I’m putting mine back together tomorrow
@Noscrap9093 жыл бұрын
Thank you , just had the same problem. Your video saved me a lot of grief !
Пікірлер
lol I’m down the street from them guys lol
Before the cover comes off there’s a bolt that goes into the shaft, how did that come off since it spins with the crank shaft when you turn it. And is it reverse thread since on a shaft? Tearing into mine now
Thanks for the video! Im doing one now! The starter is grinding. So im going to replace the starter but i think something else up inside there is bad!
Thank u. Great video. Doing the same job.
great video not a hard job 👍 👏
Thank you, I to have the same problem, do you know what the torx is to put it back together?
My starter dropped a magnet and locked it up. Now it free spins. Idk what the damage is. But breaking into it now. 06 prairie 360 4x4.
Brute force hot light stays on
How did you get the bearing back onto the flywheel when reassembling?
Curious as well if you were successful.
Do you have a rebilt video
So are all the broken teeth just scattered out In the engine?
So when you put the fly wheel back on do you need a tool to press it? Or how did you get fly wheel back on?
Would you happen to have the Phone number for turtle fountain where you got the Puller from
Purchased on eBay I’ll check and see if the phone number is still there
www.ebay.com/itm/180779750439
Do you need to worry we’re the top dead center tab is at, and also if you could post the torque that be awesome
No since you’re not removing the timing chain - I’ll get back with the torque specs I can’t recall and don’t have them with me
94 ft.lb is specs
Did you find all the broken teeth?
Yes got them all out with a magnet
I am having troubles removing the cover. I removed the 12 bolts and water pump what am I missing?
Shouldn’t be that hard to remove did you remove the impeller ?
Your video was so helpful. Thank you. Where did you get the part from and do you have a part number? I have a 2005 Kawasaki 700. Same problem as you
Part - lj2368sc120bh starter gear , clutch and gasket from caltric on eBay the flywheel puller was also from eBay seller was dt918 - $52 bucks for that just be careful when installing the stator wire grommets if you get them wrong it will leak I also used black silicone for that
PA Off-road Thank you!!
Did you get the torque specs? I’m putting mine back together tomorrow
Thank you , just had the same problem. Your video saved me a lot of grief !
12jjnmy212 2jkmmjytrttmmm233emmmrr Mqwnhhhh=#e÷eeedfnnnvbbbfdrrrrrrre ebb ere2e2t33rggg. ....mm M.mggggtt%38
P90pp[ 6th pp999
What did you do to press the magneto back onto the crankshaft?
It slides back on pretty easy no need to press fit