Brewtools B80Pro | Hot Side Brewery Tour
Тәжірибелік нұсқаулар және стиль
Grapefruit Gose Recipe:
rb.gy/gaxtmt
HLT:
Ss Brewtech 37L / 10gal Kettle ( Original Version out of production)
rb.gy/rcmf4p
Spike Brewing 10gal Steam Condenser Lid
rb.gy/getjad
Changed out spikes condenser for one i already had
Craft Hardware Steam Condenser
rb.gy/o0kbar
Ss Brewtech 2.25” Sight Glass
rb.gy/909o6f
The base of the condenser is attached to the kettles handle with an early version of Craft Hardwares kettle Lid Hinge.
Craft Hardware Kettle Lid Hinge
rb.gy/gfvpkf
Generic 3” - 1.5” Sanitary Bowl Reducer
rb.gy/v8hzwi
Brew Hardware Spincycle Weldless Kettle Whirlpool Return
rb.gy/zmn80t
Brewtools TC34mm Weldless Fitting
rb.gy/cgn8ln
Brewtools Dip tube, short Without O-rings
rb.gy/l45dnj
Brewtools 34mm TC Ball Valve, Straight
rb.gy/qfp8hy
Caso Pro 3500 Mobile Induction Hob
rb.gy/v1b915
The hose from the HLT to the B80 has 2 barbed fittings and was cut to size.
Brewtools Silicone Tube 16X25mm, Clear Food Grade
rb.gy/2utcm6
Brewtools TC34mm to 19mm hose barb (X 2)
rb.gy/ufibkp
This leads into the right sparge / pump port of the Brewtools System.
Brewtools B80pro Brewing System
rb.gy/toqaej
Brewtools B80pro Starter pack, 4-valve setup
rb.gy/ebdhgj
Brewtools B80pro 34mm Right Pump / Sparging Port Set-Up:
Brewtools 34mm Dip tube, Adjustable
rb.gy/s1z16t
Brewtools TC 90 Degree Elbow
rb.gy/4pkesq
Brewtools 3-Way TC Ball Valve
rb.gy/sctsa9
Brewtools 34mm TC Tee, L=60mm
rb.gy/aeeax7
Brewtools TC34mm Pull-type PRV
rb.gy/0nqcyk
Brewtools Silicone Tube 16X25mm, Clear Food Grade
rb.gy/2utcm6
Brewtools TC34mm to 19mm hose barb
rb.gy/ufibkp
Brewtools Inline Temp-sensor with adapter
rb.gy/mxkksm
Brewtools 34mm TC to 1/2” F-BSP/R w/Gasket groove
rb.gy/bs90db
Brewtools Gaskets for Pump Fittings
rb.gy/nuj7wv
Lower Left Pump Output Port:
Brewtools 34mm Classic Sight Glass
rb.gy/v1dlxu
Brewtools 3-Way TC Ball Valve (X2)
rb.gy/sctsa9
Brewtools 34mm Modern Sight Glass (X2)
rb.gy/sfbudr
Brewtools TC 90 Degree Elbow (X2)
rb.gy/4pkesq
Brewtools TC34mm to 19mm hose barb (X2)
rb.gy/ufibkp
Brewtools Silicone Tube 16X25mm, Clear Food Grade
rb.gy/2utcm6
Upper Left 34mm System Port:
Brewtools 3-Way TC Ball Valve (X2)
rb.gy/sctsa9
Brewtools Inline Temp-sensor with adapter
rb.gy/mxkksm
Brewtools TC34mm to 19mm hose barb (X2)
rb.gy/ufibkp
Brewtools Silicone Tube 16X25mm, Clear Food Grade
rb.gy/2utcm6
Chiller Set-up:
Brewtools 34mm TC Counter Flow Cooler Pro
rb.gy/snj62m
Brewtools TC 90 Degree Elbow (X2)
rb.gy/4pkesq
Brewtools TC34mm to 19mm hose barb (X3)
rb.gy/ufibkp
Brewtools 34mm TC Garden Hose Adapter
rb.gy/eysmum
Transferring to Fermenter / Filling System with water
Brewtools TC 90 Degree Elbow
rb.gy/4pkesq
Brewtools 34mm TC Garden Hose Adapter
rb.gy/eysmum
Brewtools Silicone Tube 16X25mm, Clear Food Grade
rb.gy/2utcm6
Brewtools TC34mm to 19mm hose barb (X2)
rb.gy/ufibkp
I relocated the Brewtools Systems control box using the available cable extensions and Control Box Bracket.
Brewtools Cable Extension Kit, 2.5m
rb.gy/e15ks2
Brewtools Bracket for Control Box
rb.gy/lxkdj9
The Malt Basket has been upgraded with the Brewtools Laser Cut Filter. The basket has also had the alternate, extra large, malt pipe latches added.
Brewtools Laser Cut Filter
rb.gy/c4p1sb
Brewtools Malt pipe latches, XL
rb.gy/xbwgsy
Brewtools Mash Temp Sensor 500mm
rb.gy/7wmhcs
Boiling:
Brewtools Steam Hat B80pro with Silicone Plug and Seal
rb.gy/rd9vrx
Brewtools Steam Condenser
rb.gy/czc7qx
Attached to the 34mm fitting on top of the condenser is a metal coffee machine hose i found at a local hardware store. i added a 34mm threaded TC fitting to the elbow of the hose to make it easy to remove when i need to remove the steam hat. The other end of the hose goes into the water splitter below the brewing table.
PEX Flexible Metal Hose
rb.gy/a4gi1f
Brewtools 34mm TC to 1/2” F-BSP/R w/Gasket groove
rb.gy/bs90db
Brewtools Gaskets for Pump Fittings
rb.gy/nuj7wv
you will need a joining 1/2” thread as the 34mm TC fitting is female and so is the thread on the elbowed portion of the water hose. These are easy to find in most plumbing departments
You will notice the plumbing on my condenser extends down lower than the standard kit. i just so happened to have a 2” to 1.5” reducer and an extra 1.5” straight pipe i wasn’t using so i decided to add it onto the end of my condenser piping.
This set up requires a total of:
33 X 34mm Tri-Clamps
8 X 1.5” Tri-Clamps
6 X 2” Tri-Clamps
1 X 3” Tri-Clamp
2 X 4” Tri-Clamps
Dont forget gaskets for each.
i think that’s everything….
Пікірлер: 20
Currently considering changing up the hoses on my b80 chiller bypass and to & from chiller to stainless. I think you've helped me decide.looks good.
Really state of art set up!
Awesome set up Mate
Nice job, and thanks for that detailed look at your set up. Taken plenty of cues for my own one from your other videos and it has always worked a charm. Did notice the lack of shots on how you have your centerpipe setup during mash. still secret stuff? :)
@MasteringHomebrew
2 жыл бұрын
Thanks!! And yes but sooooon
Very nice setup you have there! One thing bugged me though, I'd definitely go for some food-grade water hoses to avoid any plasticizers in my wort. That's surely worth it in such a high-end system.
@MasteringHomebrew
Жыл бұрын
The yellow hoses are food grade and made specifically for water for cooking / consumption and hold some EU certifications (cant remember which to be honest) certifying their materials are safe and do not leech. I took great care in choosing them and imported them myself from a company in italy. I should have touched on this. The others are just for water out and are cheap hardware store hoses.
@W00PIE
Жыл бұрын
@@MasteringHomebrew Oh, ok, my mistake. They look like standard garden hoses in my area. Nevermind.
Hello Lyndon, thank you for your great videos. Noticed that you go to the fermentor directly from the pump output instead of straight out of the chiller bypassing the kettle. Doesn't this make the cooling take longer ?
@MasteringHomebrew
2 жыл бұрын
It does make cooling longer but for me as long as I can get below 60°C in a reasonable time frame thats all that matters to me. I like to do a very slow whirlpool for about an hour after the boil has finished. Especially if I’m not in a hurry I’ll let the wort sit and settle then get a nice whirlpool going so a good bit of trub is caught in the trubinator. It can help with clarity in the final product if that’s what you’re going for. Clear in, Clear out.
You absolutely have got to check out the brew cube by ss brew tech and all its accessories. I feel like it would be perfect for your workspace
@MasteringHomebrew
2 жыл бұрын
I have seen it! Looks awesome. Brewtools is releasing their own version soon i heard!
bro, how much did this set-up cost, like 10k?!
That is a cool setup! I have 2 questions, if I may. What is the Pressure relieve valve for on the pump-in side, is this for “priming” the sparge hose? And second, what are the dimensions of the 90 and 45 degree elbows? I can’t seem to find that info anywhere (at least not after quitting Facebook and with it leaving the Brewtools Owners Group). Thanks and cheers!
@MasteringHomebrew
2 жыл бұрын
Thank you! The PRV is for priming the sparge hose in. Not always needed but certainly nice to have when you do. Im not 100% sure on all of the dimensions to be honest. 34mm TC size. Also im not using any 45s. 🤔
@JelmoNL
2 жыл бұрын
Alright thanks again I like this setup so much that I’ve copied it for my B40 :-) When chilling do you chill the whole batch and than transfer directly from kettle to fermenter once the temperature is okay, or is there any valve combination I didn’t think of that allows wort to go from the kettle to the chiller and on return go into the fermenter?
@MasteringHomebrew
2 жыл бұрын
@@JelmoNL i chill the entire thing down first since the cfc isn’t efficient enough to go straight to the unitank. Ive been thinking of adding another cfc for a single pass but i havent pulled the trigger yet. I like to do an extended whirlpool at the end sometimes. Depends on the beer.
Was the transfer of sparge water from the brewtools to the hlt acheived by gravity?
@MasteringHomebrew
2 жыл бұрын
Yes the full volume of both is enough to “push” the water into the hlt
An expensive erector set.